ASTM D1669 D1669M-2007(2013)e1 Standard Practice for Preparation of Test Panels for Accelerated and Outdoor Weathering of Bituminous Coatings《沥青覆层加速和户外风化用试片制备的标准实施规程》.pdf

1、Designation: D1669/D1669M 07 (Reapproved 2013)1Standard Practice forPreparation of Test Panels for Accelerated and OutdoorWeathering of Bituminous Coatings1This standard is issued under the fixed designation D1669/D1669M; the number immediately following the designation indicates theyear of original

2、 adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEUnits information was editorially corrected in July 2013.1. Scope1.1 This

3、practice covers a procedure for the preparation ofaccelerated and outdoor weathering test panels of bituminouscoatings. It is considered suitable for the preparation of filmthicknesses in the range from 0.25 to 2.54 mm 0.010 to 0.100in.1.2 The values stated in either SI units or inch-pound unitsare

4、to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all o

5、f thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. (WarningMercury has been designated by EPA and many state agencie

6、sas a hazardous material that can cause central nervous system,kidney, and liver damage. Mercury, or its vapor, may behazardous to health and corrosive to materials. Caution shouldbe taken when handling mercury and mercury-containingproducts. See the applicable product Material Safety DataSheet (MSD

7、S) for details and EPAs website, http:/www.epa.gov/mercury/faq.htm, for additional information. Us-ers should be aware that selling mercury or mercury-containingproducts, or both, into your state may be prohibited by statelaw.)2. Referenced Documents2.1 ASTM Standards:2B209 Specification for Aluminu

8、m and Aluminum-AlloySheet and PlateD5 Test Method for Penetration of Bituminous MaterialsE1 Specification for ASTM Liquid-in-Glass Thermometers3. Summary of Practice3.1 Heated bituminous material is poured onto a clean,heated, and masked aluminum panel. Care is taken to removeair bubbles. The bitume

9、n is leveled in a press beforesolidifying, and the coated panel is then cooled, cleaned, andmeasured for uniform thickness.4. Significance and Use4.1 This practice for preparation of test panels greatlyincreases the likelihood of achieving reproducible results insubsequent testing.5. Apparatus5.1 Pa

10、nelA supporting metal panel on which the bitumi-nous coating is applied. It shall meet the following require-ments:5.1.1 Metal, Aluminum or Aluminum Alloy, as described inTable 2 of Specification B209 under Alloy 3003-H14.35.1.2 FinishMill finish and process cleaned.5.1.3 Dimensions:5.1.3.1 Thicknes

11、s0.64 to 1.90 mm 0.025 to 0.075 in.5.1.3.2 Width and Length70 by 150 mm 234 by 578 in.or of a size that will allow a minimum bitumen film area of 50by 130 mm 2 by 518 in.1This practice is under the jurisdiction ofASTM Committee D08 on Roofing andWaterproofing and is the direct responsibility of Subc

12、ommittee D08.02 on SteepRoofing Products and Assemblies.Current edition approved July 1, 2013. Published July 2013. Originally approvedin 1959. Last previous edition approved in 2013 as D1669 07 (2013). DOI:10.1520/D1669_D1669M-07R13E01.2For referenced ASTM standards, visit the ASTM website, www.ast

13、m.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The sole sources of supply of the apparatus (panels) known to the committee atthis time are The Q-Panel Company, 26200 Firs

14、t St., Cleveland OH 44145; AtlasElectric Devices Co., 4114 N. Ravenswood Ave., Chicago, IL 60613; AdvancedCoating Technologies Inc., 273 Industrial Dr. (PO Box 401), Hillsdale MI 49242If you are aware of alternative suppliers, please provide this information to ASTMInternational Headquarters. Your c

15、omments will receive careful consideration at ameeting of the responsible technical committee,1which you may attend.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.4 FlatnessThe maximum deviation from a true flatsurface for either

16、 length or width shall not exceed 0.0005 timesthe dimension. Flatness shall be measured on a true flat surfaceemploying a curling gauge equipped with a dial which reads in0.025 mm 0.001 in. and having a foot loading of approxi-mately 100 g.45.1.5 EdgesThe edges of the panels shall be free of burrs.5

17、.1.6 StoragePanels shall be stored in a dry, well-ventilated place to prevent condensation and possible stainingor corrosion.5.2 PressThe press shall be capable of delivering a4500-kg 10 000-lb thrust and be equipped for using platens152 by 152 mm 6 by 6 in. or larger platens.55.3 PlatensThe platens

18、 shall be 152 by 152 mm 6 by 6in. or larger in size and suitable for use with the press. (Platenscan be purchased with the press.) It is preferable that bothplatens have thermostatically controlled units capable of heat-ing them to temperatures up to 260C 500F.5.4 Metal SpacersThe metal spacers shal

19、l be 13 mm 12in. wide and at least 152 mm 6 in. long and of suitablethickness so that the proper thicknesses of bitumen films can beapplied.6To cover the range from 0.254 to 2.54 mm 0.010 to0.100 in., the following supply of metal spacers is adequate:40.038 mm 0.0015 in.40.051 mm 0.002 in.40.076 mm

20、0.003 in.40.127 mm 0.005 in.40.229 mm 0.009 in.40.254 mm 0.010 in.40.305 mm 0.012 in.40.330 mm 0.013 in.40.081 mm 0.015 in.5.5 Kraft PaperThe kraft paper shall be from 64 to 191m 0.0025 to 0.0075 in. in thickness.5.6 Release PaperSilicone- or TFE-fluorocarbon-coatedrelease paper shall be cut to a si

21、ze large enough to cover theplatens of the press. It must be easily removed at roomtemperature without damaging the bitumen film. (See Note 1.)NOTE 1Dextrin-coated paper is also allowed to be used as a releasepaper. It must not leave a residue that cannot be removed by water.Asmalltank through which

22、 lukewarm water (below 27C 80F) is running shallbe used for removing dextrin-coated paper from finished panels.5.7 Heating Equipment:5.7.1 One gas or electrically heated oven capable of warm-ing the uncoated panels, thermostatically controlled so atemperature range from 93 to 204C 200 to 400F can be

23、maintained. A hot plate or any suitable plate-type heating unitcapable of thermostatically controlling the temperature be-tween 93 to 204C 200 and 400F would be adequate.5.7.2 One gas or electrically heated hot plate or oven forheating the bitumen, controlled so that container temperatureswill not e

24、xceed 316C 600F.5.8 Melting ContainerA 17-kg 6-oz. min. container ofsuitable size in which the bitumen can be melted, similar intype to that specified in Test Method D5.5.9 Thermometers:5.9.1 One ASTM Partial Immersion Thermometer, having arange from 7 to 304C 20 to 580F and conforming to therequire

25、ments for Thermometer 2C as prescribed in Specifica-tion E1, shall be used to determine the temperature of the ovenused to warm the uncoated panel.5.9.2 Two ASTM Partial Immersion Thermometers, havinga range from 7 to 304C 20 to 580F and conforming to therequirements for Thermometer 3C as prescribed

26、 in Specifica-tion E1. One shall be used to determine the temperature of thebitumen sample. The other shall be used to determine thetemperature of the oven or oil bath, if either of these is used.5.9.3 As an alternative, any other thermometric device usedshall be at least: (1) of equal accuracy to t

27、hat of the thermom-eter specified in Specification E1,(2) capable of indicatingtemperature to within 1C 2F, and (3) stable to within 1C2F for the duration of the exposure.5.10 Water BathA small tank through which lukewarmwater is running, shall be used for removing the dextrin-coatedpaper from finis

28、hed panels when the bitumen has a softeningpoint over 93C 200F. For bitumens with lower softeningpoints, the temperature of the water shall be below 27C80F.5.11 Thickness GaugeA suitable hand micrometer,caliper, or dial-type thickness gauge reading in 25 m 0.001in. and having a foot of approximately

29、 645 mm21 in.2inarea shall be used for calipering the panels.5.12 Masking TapePressure-sensitive paper or cloth tape,13 to 25 mm 12 to 1 in. in width.6. Preparation of Metal Panels6.1 HandlingHandle the panel by the edges only and donot allow fingers to contact the face to be coated. Do notunwrap th

30、e panels until the day on which they are to be coated.This is to prevent oxidation and contamination of the face. Donot reuse the test panels.6.2 Precalibration and ClassificationMeasure the thick-ness of all panels at six representative points and classify theminto groups of identical thickness.6.3

31、 MarkingMark or drill the panels before or aftercoating, preferably afterwards. If marked or drilled beforecoating, take care to see that these operations do not alter the4The sole source of supply of the apparatus (Model B-81) known to thecommittee at this time is Federal Products Corp., 1112 Eddy

32、St., Providence, RI02901. If you are aware of alternative suppliers, please provide this information toASTM International Headquarters. Your comments will receive careful consider-ation at a meeting of the responsible technical committee,1which you may attend.5The sole source of supply of the appara

33、tus (Laboratory Model Carver Presshaving a working range from 0 to 9000 kg 0 to 20 000 lb) known to the committeeat this time is Fred S. Carver, Inc., 1 Chatham Rd., Summit, NJ 07901. If you areaware of alternative suppliers, please provide this information to ASTM Interna-tional Headquarters. Your

34、comments will receive careful consideration at a meetingof the responsible technical committee,1which you may attend.6The sole source of supply of the apparatus (suitable spacers known as “shim”or “feeler” stock) known to the committee at this time is U.S. Gasket bituminous coatings; outdoorweatheri

35、ng; test panelsD1669/D1669M 07 (2013)13ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the

36、riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of

37、this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldma

38、ke your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1669/D1669M 07 (2013)14