ASTM D173-2003 Standard Specification for Bitumen-Saturated Cotton Fabrics Used in Roofing and Waterproofing《屋面和防水用沥青浸透棉织物标准规范》.pdf

1、Designation: D 173 03Standard Specification forBitumen-Saturated Cotton Fabrics Used in Roofing andWaterproofing1This standard is issued under the fixed designation D 173; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense. This standard replaces Federal SpecificationSS

3、-C-450.1. Scope1.1 This specification covers woven cotton fabrics saturatedwith either asphalt or coal-tar pitch intended to be used withasphalts conforming to Specifications D 312 or D 449, coal-tarpitches conforming to Specification D 450, or appropriatesolvent bearing bituminous materials in the

4、construction ofroofing and waterproofing systems.1.1.1 Asphalt-saturated cotton fabric shall be used withasphalt base plying cement; typical ones are mopping asphaltsconforming to Specifications D 312 or D 449 or appropriatesolvent bearing asphaltic compounds.1.1.2 Coal-tar-saturated cotton fabric s

5、hall be used withcoal-tar based plying cements; a typical one is coal-tar pitchconforming to Specification D 450 or appropriate solventbearing coal-tar compounds.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.2. Referenced

6、 Documents2.1 ASTM Standards:2D 146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Wa-terproofingD 312 Specification for Asphalt Used in RoofingD 449 Specification for Asphalt Used in Dampproofing andWaterproofingD 450 Specification for Coal-Tar Pitch

7、 Used in Roofing,Dampproofing, and WaterproofingD 1079 Terminology Relating to Roofing, Waterproofing,and Bituminous MaterialsD 3775 Test Methods for Fabric Count of Woven Fabric3. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication, refer to Terminology D 1079.4. Material

8、s and Manufacture4.1 In the process of manufacture, the dry cotton fabric shallbe thoroughly and uniformly saturated with bitumen. This shallbe accomplished by passing the fabric through the saturant orby spraying with saturant, calendering in the presence of heat,and then cooling before winding on

9、a core.4.2 If fabric with a selvage is used, the selvage shall not bemore than 16 mm (58 in.) wide.4.3 The fabric shall be woven entirely from cotton fibers,but customary sizing materials not exceeding 8 % by weight ofthe moisture-free cotton shall be permitted to be used.5. Physical Properties5.1 T

10、he material shall conform to the physical requirementsprescribed in Table 1 and the dimensions and masses pre-scribed in Table 2.5.2 The finished product shall not crack nor be so sticky asto cause tearing or other damage upon being unrolled attemperatures between 10 and 60C (50 and 140F).6. Workman

11、ship, Finish, and Appearance6.1 The meshes of the fabric shall not be completely closedor sealed by the process of saturation. There shall be sufficientporosity maintained to allow successive moppings of theplying cement to seep through.6.2 The surface of the fabric shall not be coated or coveredwit

12、h talc or other substances that would tend to interfere withadhesion between the fabric and the plying cement. The use ofsilica or wood flour is permissible.6.3 The surface shall be uniformly smooth and free ofirregularities, folds, or knots.6.4 The finished material shall be free of visible externa

13、ldefects such as ragged or untrue edges, breaks, rents, or cracks.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.04on Felts and Fabrics.Current edition approved Dec. 1, 2003. Published December 2003

14、. Originallyapproved in 1923. Last previous edition approved in 1997 as D 173 97b.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary pag

15、e onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Sampling and Test Methods7.1 Sample the material and determine compliance withthese specifications in accordance with Test Methods D 146.7.2 Determine the pliabi

16、lity of the saturated fabric at 0C(32F) by bending over a 1.6-mm (116-in.) diameter mandrelthrough an arc of 180 in one direction and then through 360in the opposite direction.7.3 Determine the thread count in accordance with TestMethod D 3775.8. Inspection8.1 InspectionInspection shall be in accord

17、ance with therequirements of this specification.8.2 Inspection AlternativesAlternative inspection require-ments shall be determined by and agreed upon between thepurchaser and the supplier.9. Rejection and Resubmittal9.1 Failure to ConformFailure to conform to any of therequirements as stated in thi

18、s specification constitutes groundsfor rejection.9.2 Rejection RedressThe supplier shall have the right toinspect the rejected materials. The supplier and the purchasershall agree to the quantity of rolls deemed unacceptable. Thesupplier shall then have the right to submit the same number ofnew roll

19、s as replacement.10. Packaging and Package Marking10.1 Unless otherwise agreed upon between the supplierand purchaser, each product package shall be plainly markedwith the suppliers name, the product brand, the ASTMdesignation, and type of bitumen if not evident in the labelname of the product.10.2

20、The rolls shall be securely wrapped or banded in amanner that completely encircles the roll and will preventslipping or unrolling.10.3 No roll shall contain more than two pieces, and nomore than 3 % of the rolls in any lot shall contain two pieces.If a roll contains a manufacturing splice, the splic

21、e shall beclearly marked.10.4 The rolls shall be wound on mandrels or rigid hollowfiber cylinders not less than 50 mm (2 in.) in diameter,extending not more than 100 mm (4 in.) beyond the end of therolls.11. Keywords11.1 bitumen-saturated; roofing and waterproofing; wovencotton fabricASTM Internatio

22、nal takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their

23、 own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be

24、 addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards

25、, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9

26、585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Physical Properties of Saturated Cotton FabricsProperty RequirementBreaking loadAat 21.1C (70F), both warp and filldirections, min, kN/m (lbf/in.)8.76 (50)Pliability at 0C (32F) no crackin

27、gACommittee D08 recognizes the advisability of including a requirement relativeto the percentage elongation before rupture, but in the absence of any reliable testmethod, such requirement cannot be stated at the present time.TABLE 2 Dimensions and Masses of Saturated Cotton Fabricsmin maxWidth of ro

28、ll, mm (in.) 762 (30) 965 (38)Gross mass per roll, kg (lb) 15.9 (35) 36.3 (80)Mass of mandrel and wrappingmaterial, kg (lb). 1.13 (2.5)Mass of detached comminutedsurfacing, g/m2(lb/100 ft2). 49 (1.0)Net mass of saturated fabric, avg,g/m2(oz/yd2)340 (10) .Thread count per 25.4 mm (1 in.)WarpFilling10

29、.2 (26)9.4 (24)12.6 (32)12.6 (32)Moisture, at point of manufacture,max, %A. 6.0Mass of desaturated, moisture-freefabric, avg, g/m2(oz/yd2)119 (312) .Ash (based on mass ofdesaturated fabric), %. 2.0Mass of saturant 1.6 3 (mass ofdesaturated,moisture-freefabric in the samearea).Selvage, mm (in.) 16 (58)AAt time of manufacture, products with higher moisture content at time ofinstallation may cause hot materials to foam, creating interply voids that may resultin blisters.D173032