ASTM D1786-2001(2006)e1 Standard Specification for Toluene Diisocyanate《甲苯二异氰酸盐标准规范》.pdf

1、Designation: D 1786 01 (Reapproved 2006)e1Standard Specification forToluene Diisocyanate1This standard is issued under the fixed designation D 1786; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTEReplaced reference to D 4667 with D 5629 in March 2006.1. Scope*1.1 This specification covers toluene diisocyanate used asan ingredient in the pr

3、oduction of polyurethane cellular mate-rials.NOTE 1The properties included in this specification are those re-quired to characterize toluene diisocyanate. Other requirements maybecome necessary and will be added as the necessary test methods becomeavailable.1.2 The following precautionary caveat per

4、tains only to thetest methods portion, Section 6, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the app

5、licability of regulatory limita-tions prior to use.NOTE 2There is no equivalent ISO standard.2. Referenced Documents2.1 ASTM Standards:2D 883 Terminology Relating to PlasticsD 4660 Test Methods for Polyurethane Raw Materials:Determination of the Isomer Content of Toluenediisocy-anateD 4661 Test Meth

6、ods for Polyurethane Raw Materials:Determination of Total Chlorine in IsocyanatesD 4663 Test Method for Polyurethane Raw Materials: De-termination of Hydrolyzable Chlorine of IsocyanatesD 4877 Test Method for Polyurethane Raw Materials: De-termination of APHA Color in IsocyanatesD 5155 Test Methods

7、for Polyurethane Raw Materials:Determination of the Isocyanate Content of AromaticIsocyanatesD 5629 Test Method for Polyurethane Raw Materials: De-termination of Acidity in Low-Acidity Aromatic Isocyan-ates and Polyurethane Prepolymers2.2 Federal Standard:49 CFR Transportation Part 172.0133. Termino

8、logy3.1 DefinitionsFor definitions of terms used in this speci-fication, see Terminology D 883.4. Classification4.1 This specification covers three classes of toluene diiso-cyanates, based on isomer ratio, and three types based onacidity and hydrolyzable chloride.4.2 Each class may be subdivided int

9、o three types on thebasis of acidity differences as follows:4.2.1 TypeIorAAcidity shall be between 0.0015 and0.0045 determined as percent HCl. Hydrolyzable chloride shallbe less than 0.01 %.4.2.2 Type II or BAcidity shall be between 0.0070 and0.012 as percent HCl. Hydrolyzable chloride shall be less

10、 than0.015 %.4.2.3 Type III or CAcidity shall be greater than 0.012 aspercent HCl. Hydrolyzable chloride limits may be set at theconvenience of the supplier and purchaser.5. Requirements5.1 These materials shall conform to the requirementsprescribed in Table 1.6. Sampling and Test Methods6.1 The mat

11、erials shall be sampled and tested in accordancewith Test Methods D 4660, D 4661, D 4663, D 4877, D 5155,and D 5629.1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.22 on CellularMaterialsPlastics and Elastomers.Curre

12、nt edition approved March 15, 2006. Published May 2006. Originallyapproved in 1960. Last previous edition approved in 2001 as D 1786 - 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume

13、information, refer to the standards Document Summary page onthe ASTM website.3Code of Federal Regulation is available from U.S. Government Printing OfficeSuperintendent of Documents, 732 N. Capitol St., NW, Mail Stop: SDE, Washing-ton, DC 20401.1*A Summary of Changes section appears at the end of th

14、is standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Retest and Rejection7.1 If any failure occurs, the material may be retested toestablish conformity in accordance with agreement betweenthe purchaser and the seller.8. Pack

15、aging and Package Marking8.1 PackagingThe material shall be packaged in standardcommercial containers so constructed as to ensure compliancewith Department of Transportation standards for such contain-ers and shall be suitable for safe transportation at the lowestrate to the point of delivery. OSHA4

16、and EPA5regulations mayalso apply and should be consulted.8.2 MarkingShipping containers/documents shall bemarked with the name of the material, type, and the quantitycontained therein, and necessary hazard labels as defined bythe Department of Transportation for this material, the name ofthe manufa

17、cturer, manufacturers emergency telephone num-ber in case of accident, and the number of the contract or order.OSHA4and EPA5regulations may also apply and should beconsulted.9. Keywords9.1 polyurethane; raw materials; specification; TDI; toluenediisocyanateSUMMARY OF CHANGESCommittee D20 has identif

18、ied the location of selected changes to this standard since the last issue,D 1786 - 01, that may impact the use of this standard. (March 15, 2006)(1) Replaced reference to D 4667 with D 5629 to reflect thefact that D 4667 has been withdrawn and D 5629 is now theapplicable standard.ASTM International

19、 takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their ow

20、n responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be ad

21、dressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, a

22、t the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585

23、 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).4Available from U.S. Department of Labor, OSHA, 200 Constitution Ave. NW,Washington, DC 20210.5Available from United States Environmental Protection Association (EPA),Ariel Rios Bldg., 1200 Pennsylvania Ave., NW, Washington, DC 20460.TABLE 1 Detail Requirements for Toluene DiisocyanateClass100 80 65Isomer ratio, 2, 4 isomer, % 97.5 min 80 6 2656 2Purity, min, % 99.5 99.5 99.5APHA color, max 50 50 50Total chlorine, max, % 0.2 0.2 0.2D 1786 01 (2006)e12