ASTM D1875-2003(2013) Standard Test Method for Density of Adhesives in Fluid Form《液态胶粘剂密度的标准试验方法》.pdf

1、Designation: D1875 03 (Reapproved 2013)Standard Test Method forDensity of Adhesives in Fluid Form1This standard is issued under the fixed designation D1875; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This test method covers the measurement of density(

3、weight per gallon) of adhesives, and components thereof,when in liquid form.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with it

4、s use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D907 Terminology of AdhesivesE1 Specification for ASTM Liquid-in-Glass

5、ThermometersE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3. Terminology3.1 DefinitionsMany terms in this test method are definedin Terminology D907.3.2 Definitions of Terms Specific to This Standard:3.2.1 density, nthe mass (weight in vacuum) of a u

6、nitvolume of the liquid at any given temperature expressed as theweight in pounds avoirdupois, of a U.S. gallon measure of theliquid at 25C, unless otherwise specified.4. Significance and Use4.1 This test method is particularly applicable where thefluid has too high a viscosity or where a component

7、is toovolatile for a specific gravity balance determination.5. Apparatus5.1 Weight-Per-Gallon CupA weight-per-gallon cup3ofplated brass or stainless steel with counterbalance is recom-mended. The capacity of this cup with cover is exactly 83.2 mL(2.81 fl oz) at 25C (77F).NOTE 1The use of cups that a

8、re factory calibrated eliminates the needfor further calibration. These cups are calibrated with distilled water sothat their proper net weight is obtained at 25C. A temperature of 25C istherefore recommended when using these cups. Volume expansion of bothcup and the material to be measured causes e

9、rroneous results, if the matterof temperature is not standardized. However, where less accuracy isrequired, consideration of temperature differentials may be ignored.5.2 ThermometerASTM Saybolt Viscosity Thermometerhaving a range from 19 to 27C (66 to 80.5F) and conformingto the requirements for The

10、rmometer 17C as prescribed inSpecification E1.5.3 Constant-Temperature Bath, capable of maintaining atemperature of 25 6 0.1C (77 6 0.5F).5.4 Laboratory Balance, 200 g (0.44 lb) or greater capacity,accurate to 60.1 g (0.0002 lb).NOTE 2A hanging pan, triple-beam balance, or overhead-beam typeof balan

11、ce with scales graduated to 0.1 g has been found to provide results,the mean of which was consistent with the over all precision and accuracyof this test method.NOTE 3Fingerprints and smudges on the cup changes the weight andis to be avoided. Handle only with tongs and with hands protected byclean,

12、dry, absorbent material.6. Sampling6.1 Take representative samples of the lot to be evaluatedfrom three or more separate containers, chosen at random. Donot take samples from containers that appear to be nonrepre-sentative. Place the samples in airtight containers, filled toprevent excessive air spa

13、ce above the adhesive, and stored atroom temperature to reduce evaporation or drying to a mini-mum. Ensure that the adhesive in the container is thoroughlymixed if there is a tendency for the materials to separate.7. Procedure7.1 Test three portions of each sample.7.2 Clean and dry the cup with nonr

14、esidual solvents.1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.10 on WorkingProperties.Current edition approved Oct. 1, 2013. Published October 2013. Originallyapproved in 1961. Last previous edition approved in 200

15、8 as D1875 03 (2008)1.DOI: 10.1520/D1875-03R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Weight-per-ga

16、llon cups may be obtained from the Paul N. Gardner Co.,Pompano Beach, FL.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17.3 Fill the cup with the adhesive at a temperature below25C. Force down the cap for the cup to the extent of its

17、 travel,leaving the overflow orifice open. Immediately remove anyexcess overflow of adhesive from the cup by a suitable volatilesolvent. Avoid air bubbles occluded within the cup.7.4 Bring the cup and contents to the specified temperature,25C. Use the constant-temperature bath or room if necessary.T

18、his may be expected to cause further slight flow of adhesivefrom the overflow orifice due to expansion of the adhesive withthe rise of temperature.7.5 Remove the excess overflow by carefully wiping with asuitable solvent on an absorbent material. Dry the outside ofthe cup, if necessary, by wiping wi

19、th the absorbent material.Do not remove overflow that occurs subsequent to the firstwiping after attainment of the desired temperature. Weigh thefilled cup immediately to the nearest 0.1 g using the counter-balance for the cup.8. Calculation8.1 If the regular weight-per-gallon cup with capacity of83

20、.2 mL is used, the weight in grams of the contents, dividedby 10, is the weight per gallon in pounds, or calculate thedensity in pounds per gallon as follows:D 5 WKwhere:D = density, lb/gal,W = weight of contents, g, (8.3455)/V = constant for cup atcalibration temperature (Note 4), orK = 0.1003065 f

21、or cup with 83.2-mL capacity at 25C (Kconsidered as = 0.1, unless greater accuracy is desired),andV = volume of cup, mL.NOTE 4The numerator of K, 8.3455, is calculated from the volume-weight relationship as follows:2.540033231.00!/453.59 5 8.3455where:2.5400 = conversion factor for centimetres to in

22、ches231.00 = conversion for cubic inches to gallons, and453.59 = conversion factor for grams to pounds.9. Report9.1 Report the following information:9.1.1 Complete identification of the adhesive tested, includ-ing type, source, manufacturers code number, lot or batchnumber, condition, and date.9.1.2

23、 Number of containers received and number sampled.9.1.3 Number of samples tested, and9.1.4 Average density to the third decimal in pounds pergallon at the specified temperature (for example, D = X.XXXlb/gal at 25C), and the maximum and minimum values.10. Precision and Bias410.1 The number of laborat

24、ories, materials, and determina-tions in this study DOES NOT meet the minimum require-ments for determining precision prescribed in Practice E691:PRACTICE E691 STUDY MINIMUMLaboratories 1 6Materials 3 4Determinations 10 210.1.1 Precision statement for test method: wt per volPrecision, characterized

25、by repeatability, Sr, r, andreproducibility, SR, R has been determined for the materials tobe:Materials Average Sr SR r RA 10.83 0.01 0.01 0.03 0.03B. 10.81 0.02 0.02 0.04 0.04C 10.81 0.01 0.01 0.02 0.0210.1.2 This precision statement is provisional. Within fiveyears, additional data will be obtaine

26、d and processed whichdoes meet the requirements of Practice E691.11. Keywords11.1 density; weight-per-gallonASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised t

27、hat determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapp

28、roved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you

29、feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual r

30、eprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).4Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D14-1014. ContactASTM CustomerService at serviceastm.org.D1875 03 (2013)2