ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:68.69KB ,
资源ID:511206      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-511206.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D2209-2000(2015) Standard Test Method for Tensile Strength of Leather《皮革拉伸强度的标准试验方法》.pdf)为本站会员(sofeeling205)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D2209-2000(2015) Standard Test Method for Tensile Strength of Leather《皮革拉伸强度的标准试验方法》.pdf

1、Designation: D2209 00 (Reapproved 2015)Standard Test Method forTensile Strength of Leather1This standard is issued under the fixed designation D2209; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numb

2、er in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This test method covers the determination of the load

3、required to rupture a leather test specimen having a12-in.(12.7-mm) width. The load to rupture divided by the originalunstretched cross-sectional area gives the tensile strength. Itmay be used for all types of leather that are smooth and firmenough to permit accurate thickness measurements. This tes

4、tmethod does not apply to wet blue.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of

5、 the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D1517 Terminology Relating to LeatherD1610 Practice for Conditioning Leather and Leather Prod-ucts for T

6、estingD1813 Test Method for Measuring Thickness of LeatherTest SpecimensD2211 Test Method for Elongation of Leather3. Terminology3.1 For definitions of leather terms used in this standardrefer to Terminology D1517.4. Summary of Test Method4.1 The width and thickness are measured in the center ofthe

7、narrow area of the leather specimen. The specimen isclamped in the testing machine as described in 9.3. The forcerequired to rupture the leather at a jaw separation of 10 6 2in./min. is measured. The tensile strength is calculated in psi orin kPa by dividing the force by the area of the original cro

8、sssection of its narrow section. The percent elongation at ruptureis also measured.5. Significance and Use5.1 The tensile strength test gives a reliable indication of thequality of the leather. Improperly lubricated and partiallydegraded leathers give low values for tensile strength. Theorientation

9、of the specimen in relation to the backbone and thelocation of the specimen on the hide influence the resultssignificantly. This test method is excellent for development,control, specification acceptance, and service evaluation ofleather. This test method may not apply when the conditions oftest emp

10、loyed differ widely from those specified in the testmethod.6. Apparatus6.1 Testing Machine, Power-Driven The applied loadshall be indicated on a dial, scale, or chart. The load indicatorshall record or indicate the maximum load at the time ofrupture of the specimen. The machine shall be equipped wit

11、h aset of grips for clamping the specimens. The faces of the gripsshould be knurled or otherwise roughened to prevent slippingof the specimen. The gripping surfaces shall be at least 1 by 112in. (25.4 by 38 mm). The grips shall be mounted with thelonger dimension perpendicular to the direction of th

12、e appli-cation of the load. The speed of the power-activated grip shallbe uniform speed of 10 6 2 in./ min (254 6 50 mm/min) whenrunning free. The error of the machine up to a load of 50 lbf(222 N) shall not exceed 2 %; at loads of more than 50 lbf theerror shall not exceed 1 %.6.2 Thickness GageAde

13、ad-mass type of thickness gage asdescribed in Test Method D1813.6.3 Steel Scale, graduated to read in 0.02 in. (0.5 mm).6.4 Steel Die, to cut test specimens designed as shown inFig. 1.6.5 Cutting Block, which shall consist of a flat hardwoodsupport upon which is placed a flat, smooth sheet of firmma

14、terial that will not injure the cutting edge of the die.1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.07 on Physical Properties. Thistest method was developed in cooperation with the American Leather ChemistsAssn. (St

15、andard Method E15 1965).Current edition approved May 1, 2015. Published July 2015. Originally approvedin 1963. Last previous edition approved in 2010 as D2209 00 (2010). DOI:10.1520/D2209-00R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at s

16、erviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17. Test Specimen7.1 The specimen shall be dumbbell in

17、 shape, cut from thetest unit of leather by means of a die as shown in Fig. 1. Thedirection of the long dimension in relation to the backboneshall be noted.8. Conditioning8.1 All specimens shall be conditioned in accordance withPractice D1610. Conditioning other than that prescribed shallbe noted in

18、 the results.9. Procedure9.1 Measure the thickness of the specimen to the nearest0.001 in. (0.025 mm) at one point, the mid-point of the narrowsection.9.2 Measure the width of the narrow section of the spectrumto the nearest 0.02 in. (0.5 mm) at one place on the grain side,at the mid-point. Measure

19、heavy leathers such as belting andsoling, on both flesh and grain sides at the mid-point.9.3 Mount the specimen symmetrically with the distancebetween the jaws 4 618 in. (102 6 3.2 mm).9.4 Determine the elongation of the specimen in accordancewith Test Method D2211.9.5 Record the load in pounds-forc

20、e (or newtons) to rupturethe specimen.9.6 Reject any specimen that slips or breaks within34 to 1in. (19 to 25.4 mm) of the jaws and test a similar specimen.10. Report10.1 Report the following information:10.1.1 Thickness to the nearest 0.001 in. (0.025 mm)reported for each specimen or averaged and r

21、eported as thethickness of the sample.10.1.2 Cross-sectional area of each specimen,NOTE 1Calculate the original cross-sectional area of the specimenfrom one thickness measurement and one width measurement. For heavyleathers average two width measurements.10.1.3 Breaking load to the nearest 1 lbf (4.

22、4 N), reportedfor each specimen or averaged and reported as the breakingload of the sample,10.1.4 Tensile strength to the nearest 10 psi (69 kPa),reported for each specimen or averaged and reported as thetensile strength of the sample, andNOTE 2Calculate the tensile strength by dividing the load in

23、pounds-force (or newtons) required to rupture the specimen by the area in squareinches (or square millimetres) of the original cross section of its narrowsection.10.1.5 Direction of the long axis of the specimen relative tothe backbone.11. Precision and Bias11.1 The following criteria may be used to

24、 judge theacceptability of the results if at least 15 units have been tested:11.1.1 One Operator, Duplicate Specimens, Same SkinResults by the same operator on duplicate adjacent specimensfrom a skin taken from the official sampling location should notbe considered suspect unless the coefficient of

25、variation ex-ceeds:Shoe upperCalfskinA11 %8%A31oz(8528g),0.0468 0.0156 in. (1.189 0.396 mm).11.1.2 Two Laboratories, Duplicate Specimens, SameSkinResults submitted on leathers of the type mentioned in11.1.1 by each of two laboratories on duplicate adjacentspecimens from the same skin taken from the

26、official samplingposition should not be considered suspect unless the average ofthe two results differ by more than 5 %.NOTE 3The reproducibility reported in 11.1.2 is based on dataobtained at two laboratories, each with a different type of testing machineand a different operator. One machine is a l

27、oad-cell type and the other apendulum type. The results show very close correlation between labora-tories.NOTE 4The precision data for between skins are not given because theresults were based on different skins from several production lots. Thevariables in leather for between skins will give a high

28、er variation of theresults, but this factor should not affect the precision of the test method.12. Keywords12.1 leather; strength; tensile strengthin. mm in. mm12 12.7 114 31.878 22 6 1521 25.4 634 171118 28.6NOTE 1The cutting edges shall be beveled on the outside and straighton the inside. The die

29、shall be kept sharp and free of nicks to give clean,even edges on the specimen.FIG. 1 Shape and Dimensions of Die for Cutting Test SpecimensD2209 00 (2015)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard

30、. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed

31、every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible te

32、chnical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoh

33、ocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 00 (2015)3

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1