ASTM D2241-2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)《聚氯乙烯 (PVC) 压力标定管 (SDR系列) 的标准规格》.pdf

1、Designation: D2241 09D2241 15Standard Specification forPoly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDRSeries)1This standard is issued under the fixed designation D2241; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year o

2、f last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers pol

3、y(vinyl chloride) (PVC) pipe made in standard thermoplastic pipe dimension ratios andpressure rated for water (see appendix). Included are criteria for classifying PVC plastic pipe materials and PVC plastic pipe, asystem of nomenclature for PVC plastic pipe, and requirements and test methods for mat

4、erials, workmanship, dimensions,sustained pressure, burst pressure, flattening, and extrusion quality. Methods of marking are also given.1.2 The products covered by this specification are intended for use with the distribution of pressurized liquids only, which arechemically compatible with the pipi

5、ng materials. Due to inherent hazards associated with testing components and systems withcompressed air or other compressed gases, some manufacturers do not allow pneumatic testing of their products. Consult withspecific product/component manufacturers for their specific testing procedures prior to

6、pneumatic testing.NOTE 1Pressurized (compressed) air or other compressed gases contain large amounts of stored energy which present serious safety hazards shoulda system fail for any reason.NOTE 2This standard specifies dimensional, performance and test requirements for plumbing and fluid handling a

7、pplications, but does not addressventing of combustion gases.1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notesand footnotes (excluding those in tables and figures) shall not be considered as requirements of the specificatio

8、n.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.5 The following safety hazards caveat pertains only to the test methods portion

9、, Section 8, of this specification:This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations

10、 prior to use.A specific precautionary statement is given in Note 9Note 7. .NOTE 3CPVC plastic pipe (SDR-PR), which was formerly included in this specification, is now covered by Specification F442/F442M.NOTE 4The sustained and burst pressure test requirements, and the pressure ratings in the append

11、ix, are calculated from stress values obtained fromtests made on pipe 4 in. (100 mm) and smaller. However, tests conducted on pipe as large as 24 in. (600 mm) in diameter have shown these stress valuesto be valid for larger diameter PVC pipe.NOTE 5PVC pipe made to this specification is often belled

12、for use as line pipe. For details of the solvent cement bell, see Specification D2672 andfor details of belled elastomeric joints, see Specifications D3139 and D3212.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1598 Test Method for Time-to-Failure of

13、 Plastic Pipe Under Constant Internal PressureD1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating to Plastics1 This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Syst

14、emsand is the direct responsibility of Subcommittee F17.25 on Vinyl BasedPipe.Current edition approved Dec. 1, 2009March 1, 2015. Published December 2009March 2015. Originally approved in 1964. Last previous edition approved in 20052009as D2241 05.D2241 09. DOI: 10.1520/D2241-09.10.1520/D2241-15.2 F

15、or referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to pr

16、ovide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof th

17、e standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D1784 Specification for Rigid Poly(Vinyl Chlori

18、de) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)CompoundsD2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by AcetoneImmersionD2444 Test Method for Det

19、ermination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (FallingWeight)D2672 Specification for Joints for IPS PVC Pipe Using Solvent CementD2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis forThermoplas

20、tic Pipe ProductsD3139 Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric SealsD3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric SealsF412 Terminology Relating to Plastic Piping SystemsF442/F442M Specification for Chlorinated Poly

21、(Vinyl Chloride) (CPVC) Plastic Pipe (SDRPR)2.2 NSF Standards:3Standard No. 14 for Plastic Piping Components and Related MaterialsStandard No. 61 for Drinking Water Systems ComponentsHealth Effects3. Terminology3.1 DefinitionsDefinitions are in accordance with Terminology F412, and abbreviations are

22、 in accordance with TerminologyD1600, unless otherwise specified. The abbreviation for poly(vinyl chloride) plastic is PVC.3.2 Definitions of Terms Specific to This Standard:3.2.1 hydrostatic design stressthe estimated maximum tensile stress the material is capable of withstanding continuously witha

23、 high degree of certainty that failure of the pipe will not occur. This stress is circumferential when internal hydrostatic waterpressure is applied.3.2.2 pressure rating (PR)the estimated maximum water pressure the pipe is capable of withstanding continuously with a highdegree of certainty that fai

24、lure of the pipe will not occur.3.2.3 relation between standard dimension ratio, hydrostatic design stress, and pressure ratingThe following expression,commonly known as the ISO equation,4 is used in this specification to relate standard dimension ratio, hydrostatic design stress,and pressure rating

25、:2S/P 5R 21or 2S/P 5D0/t! 21 (1)where:S = hydrostatic design stress, psi (or MPa),P = pressure rating, psi (or MPa),D0 = average outside diameter, in. (or mm),t = minimum wall thickness, in. (or mm), andR = standard thermoplastic pipe dimension ratio (D0/t for PVC pipe), also known as SDR.3.2.4 stan

26、dard thermoplastic pipe dimension ratio (SDR)the ratio of pipe diameter to wall thickness. For PVC pipe it iscalculated by dividing the average outside diameter of the pipe in inches or millimetres by the minimum wall thickness in inchesor millimetres. If the wall thickness calculated by this formul

27、a is less than 0.060 in. (1.52 mm), it shall be arbitrarily increased to0.060in. (1.52 mm). The SDR values shall be rounded to the nearest 0.5.3.2.5 standard thermoplastic pipe materials designation codeThe pipe materials designation code shall consist of theabbreviation PVC for the type of plastic,

28、 followed by the ASTM type and grade in Arabic numerals and the design stress in unitsof 100 psi (0.7 MPa) with any decimal figures dropped. When the design stress code contains less than two figures, a cipher shallbe used before the number, thus a complete material code shall consist of three lette

29、rs and four figures for PVC plastic pipematerials.4. Classification4.1 GeneralThis specification covers PVC pipe made and marked with one of six Type/Grade/Design Stress designations (seeX1.2) in eleven standard dimension ratios.4.2 Standard Thermoplastic Pipe Dimension Ratios (SDR)This specificatio

30、n covers PVC pipe in eleven standard dimensionratios, namely, 13.5, 17, 21, 26, 32.5, 41, and 64 (in the body of the document) and 11, 35, 51 and 81 (in Annex A1.) Standarddimension ratios are uniform for all nominal pipe sizes for each material and pressure rating. These are referred to as SDR 11,3

31、 Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http:/www.nsf.org.4 ISO R1611960, Pipes of Plastics Materials for the Transport of Fluids (Outside Diameters and Nominal Pressures) Part 1, Metric Series.D2241 152SDR13.5, SDR17, SDR21, SDR26, SDR32.5,

32、SDR35, SDR41, SDR51, SDR64, and SDR81, respectively. The pressure rating isuniform for all nominal pipe sizes for a given PVC pipe material and SDR (see Table X1.1).4.3 Hydrostatic Design StressesThis specification covers pipe made from PVC plastics defined by four hydrostatic designstresses develop

33、ed on the basis of long-term tests (appendix).5. Materials5.1 GeneralPoly(vinyl chloride) plastics used to make pipe meeting the requirements of this specification are categorized bymeans of two criteria, namely, (1) short-term strength tests, and (2) long-term strength tests.NOTE 6The PVC pipe inte

34、nded for use in the transport of potable water should be evaluated and certified as safe for this purpose by a testing agencyacceptable to the local health authority. The evaluation should be in accordance with requirements for chemical extraction, taste, and odor that are noless restrictive than th

35、ose included in NSF Standard No. 14. The seal or mark of the laboratory making the evaluation should be included on the pipe.See pipe marking requirement for reclaimed water systems.5.2 Basic MaterialsThis specification covers pipe made from PVC plastics having certain physical and chemical properti

36、esas described in Specification D1784.5.3 CompoundThe PVC compounds used for this pipe shall equal or exceed one of the following classes described inSpecification D1784: PVC 12454 or 14333.5.4 Rework MaterialThe manufacturer shall use only his own clean rework pipe material and the pipe produced sh

37、all meetall the requirements of this specification.6. Requirements6.1 Dimensions and Tolerances:6.1.1 Outside DiametersThe outside diameters and tolerances shall be as shown in Table 1 when measured in accordance withTest Method D2122. The tolerances for out-of-roundness shall apply only on pipe pri

38、or to shipment.6.1.2 Wall ThicknessThe wall thicknesses and tolerances shall be as shown in Table 2 when measured in accordance with TestMethod D2122.TABLE 1 IPS PVC PipeOutside Diameters and TolerancesNominal PipeSize, in.Average Outside Diameter,in. (mm)Tolerances, in. (mm)For AverageMaximum Out-o

39、f-Roundness(Maximum Minimum Diameter)SDR64,SDR41,SDR32.5,SDR26,SDR21SDR17,SDR13.518 0.405 (10.29) 0.004 (0.10) 0.030 (0.76) 0.016 (0.41)14 0.540 (13.72) 0.004 (0.10) 0.030 (0.76) 0.016 (0.41)38 0.675 (17.14) 0.004 (0.10) 0.030 (0.76) 0.016 (0.41)12 0.840 (21.34) 0.004 (0.10) 0.030 (0.76) 0.016 (0.41

40、)34 1.050 (26.67) 0.004 (0.10) 0.030 (0.76) 0.020 (0.51)1 1.315 (33.40) 0.005 (0.13) 0.030 (0.76) 0.020 (0.51)114 1.660 (42.16) 0.005 (0.13) 0.030 (0.76) 0.024 (0.61)112 1.900 (48.26) 0.006 (0.15) 0.060 (1.52) 0.024 (0.61)2 2.375 (60.32) 0.006 (0.15) 0.060 (1.52) 0.024 (0.61)212 2.875 (73.02) 0.007

41、(0.18) 0.060 (1.52) 0.030 (0.76)3 3.500 (88.90) 0.008 (0.20) 0.060 (1.52) 0.030 (0.76)312 4.000 (101.60) 0.008 (0.20) 0.100 (2.54) 0.030 (0.76)4 4.500 (114.30) 0.009 (0.23) 0.100 (2.54) 0.030 (0.76)5 5.563 (141.30) 0.010 (0.25) 0.100 (2.54) 0.060 (1.52)6 6.625 (168.28) 0.011 (0.28) 0.100 (2.54) 0.07

42、0 (1.78)8 8.625 (219.08) 0.015 (0.38) 0.150 (3.81) 0.090 (2.29)10 10.750 (273.05) 0.015 (0.38) 0.150 (3.81) 0.100 (2.54)12 12.750 (323.85) 0.015 (0.38) 0.150 (3.81) 0.120 (3.05)14 14.000 (355.60) 0.015 (0.38) 0.200 (5.08) 0.150 (3.81)16 16.000 (406.40) 0.019 (0.48) 0.320 (8.13) 0.160 (4.06)18 18.000

43、 (457.20) 0.019 (0.48) 0.360 (9.14) 0.180 (4.57)20 20.000 (508.00) 0.023 (0.58) 0.400 (10.2) 0.200 (5.08)24 24.000 (609.60) 0.031 (0.79) 0.480 (12.2) 0.240 (6.10)30 30.000 (762.00) 0.041 (1.04) 0.600 (15.2) 0.300 (7.62)36 36.000 (914.40) 0.050 (1.27) 0.720 (18.3) 0.360 (9.14)D2241 1536.2 Sustained P

44、ressureThe pipe shall not fail, balloon, burst, or weep as defined in Test Method D1598 at the test pressuresgiven in Table 3 when tested in accordance with 8.4.6.2.1 Accelerated Regression TestThe accelerated regression test shall be used in place of both the sustained and burstpressure tests, at t

45、he option of the manufacturer. The test shall be conducted in accordance with 8.4.1. The pipe shall demonstratea hydrostatic design basis projection at the 100 000-h intercept that meets the hydrostatic design basis category requirement (seethe table for “Hydrostatic Design Basis Categories” of Test

46、 Method D2837) for the PVC material used in its manufacture.(Example: PVC 1120 pipe must have a minimum 100 000-h projection of 3830 psi and 85 % lower confidence limit (LCL).)6.3 Burst PressureThe minimum burst pressures for PVC plastic pipe shall be as given in Table 4, when determined inaccordanc

47、e with 8.5.6.4 FlatteningThere shall be no evidence of splitting, cracking, or breaking when the pipe is tested in accordance with 8.6.TABLE 2 Wall Thicknesses and Tolerances for PVC Plastic Pipe with IPS Outside DiametersNominalPipeSize, in.Wall Thickness,A in.BSDR64 SDR41 SDR32.5 SDR26 SDR21 SDR17

48、 SDR13.5Mini-mumToler-anceMini-mumToler-anceMini-mumToler-anceMini-mumToler-anceMini-mumToler-anceMini-mumToler-anceMini-mumToler-ance18 . . . . . . . . . . . . 0.060 +0.02014 . . . . . . . . . . . . 0.060 +0.02038 . . . . . . . . . . . . 0.060 +0.02012 . . . . . . . . . . . . 0.062 +0.02034 . . . .

49、 . . . . 0.060 +0.020 0.062 +0.020 0.078 +0.0201 . . . . . . 0.060 +0.020 0.063 +0.020 0.077 +0.020 0.097 +0.020114 . . . . 0.060 +0.020 0.064 +0.020 0.079 +0.020 0.098 +0.020 0.123 +0.020112 . . . . 0.060 +0.020 0.073 +0.020 0.090 +0.020 0.112 +0.020 0.141 +0.0202 . . . . 0.073 +0.020 0.091 +0.020 0.113 +0.020 0.140 +0.020 0.176 +0.020212 . . . . 0.088 +0.020 0.110 +0.020 0.137 +0.020 0.169 +0.020 0.213 +0.0263 . . 0.085 +0.020 0.108 +0.020 0.135 +0.020 0.167 +0.020 0.206 +0.025 0.259 +0.031312 . . 0.