ASTM D227-2003 Standard Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing《屋面和防水用煤焦油浸透有机毡标准规范》.pdf

1、Designation: D 227 03Standard Specification forCoal-Tar-Saturated Organic Felt Used in Roofing andWaterproofing1This standard is issued under the fixed designation D 227; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense. This specification replaces Federal specificati

3、onHH-R-595, Type 15C.1. Scope1.1 This specification covers coal-tar-saturated organic feltintended to be used with coal-tar pitches conforming to theappropriate requirements of Specification D 450 in the con-struction of built-up roofs and in the construction of water-proofing systems.1.2 The values

4、 stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Standards:2D 146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Wa-terproofingD 450 Specification for Coal-T

5、ar Pitch Used in Roofing,Dampproofing, and WaterproofingD 1079 Terminology Relating to Roofing, Waterproofing,and Bituminous Materials3. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication, refer to Terminology D 1079.4. Materials and Manufacture4.1 In the process of manuf

6、acture, a single thickness of dryfelt shall be saturated with refined coal-tar from which some ofthe more volatile constituents have been removed.4.2 The felt shall be produced principally from organicfibers or mixtures thereof. The surface of the felt shall beuniform and relatively smooth. Upon spl

7、itting or tearing on thebias, the felt shall appear reasonably free of lumps and particlesof foreign substances.5. Physical Requirements5.1 The material shall conform to the physical requirementsprescribed in Table 1.5.2 The finished product shall not crack nor be so sticky asto cause tearing or oth

8、er damage upon being unrolled attemperatures between 10 and 60C (50 and 140F).6. Workmanship, Finish, and Appearance6.1 The felt shall be saturated and shall show no unsaturatedspots at any point upon cutting 50-mm (2-in.) wide strips atrandom across the entire sheet and splitting them open to their

9、full length.6.2 The surface of the felt shall not be coated or coveredwith talc or other substances that would tend to interfere withadhesion between the felt and the plying cement.6.3 The finished material shall be free of visible externaldefects such as holes, ragged or untrue edges, breaks, crack

10、s,tears, protuberances, and indentations.7. Sampling and Test Methods7.1 Sample the material and determine the properties enu-merated in this specification in accordance with Test MethodsD 146.8. Inspection8.1 InspectionInspection shall be in accordance with therequirements of this specification.8.2

11、 Inspection AlternativesAlternative inspection require-ments shall be determined by and as agreed upon between thepurchaser and the supplier.9. Rejection and Resubmittal9.1 Failure to ConformFailure to conform to any of therequirements as stated in this specification constitutes groundsfor rejection

12、.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.04on Felts and Fabrics.Current edition approved Dec. 1, 2003. Published January 2004. Originallyapproved in 1925. Last previous edition approved in 19

13、97 as D 227 97a.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbo

14、r Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.9.2 Rejection RedressThe supplier shall have the right toinspect the rejected materials. The supplier and the purchasershall agree to the quantity of rolls deemed unacceptable. Thesupplier shall then have the right to submit the s

15、ame number ofnew rolls as replacement.10. Packaging and Package Marking10.1 Unless otherwise agreed upon between the supplierand purchaser, each package shall be plainly marked with thesuppliers name, the product brand, the ASTM designation, andtype of bitumen if not evident in the label name of the

16、 product.10.2 The rolls shall be securely wrapped or banded in amanner that completely encircles the roll and will preventslipping or unrolling.10.3 No roll shall contain more than two pieces, and nomore than 3 % of the rolls in any lot shall contain two pieces.If a roll contains a manufacturing spl

17、ice, the splice shall beclearly marked.11. Keywords11.1 built-up roofs; coal tar saturated; membrane; organicfelt; waterproofingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are

18、 expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not r

19、evised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you

20、 may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United

21、States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Physical Requirements for Coal-Tar-Saturated

22、Organic FeltWidth of roll, mm (in.) 914 (36) 6 0.7 %AArea of Roll as agreed upon between the purchaser and the sellerNet mass of saturated felt, min, g/m2(lb/100 ft2) 635 (13)Moisture, at point of manufacture, max %B4.3Average breaking strength, min, kN/m (lbf/in.) of widthCLongitudinal (with the fi

23、ber grain) 5.3 (30)Transverse (across the fiber grain) 2.6 (15)Pliability, 13 mm (12 in.) radius bend at 25C (77F) no failuresMass of desaturated (unsaturated) felt, min, g/m2(lb/100 ft2)D254 (5.2)Mass of saturant (coal-tar), min, g/m2(lb/100 ft2)E356 (7.3)AOther widths may be agreed upon between th

24、e purchaser and the seller.BAt time of manufacture, products with higher moisture content at time of installation may cause hot materials to foam, creating interply voids that may result in blisters.CIf specimens fail to conform to the requirements for breaking strength after conditioning for 2 h, a

25、 retest shall be made on specimens conditioned for 72 h. The materialshall be accepted or rejected on the basis of the retest.DThe moisture-free felt shall meet this requirement prior to saturation. Coal-tar-saturated felt cannot be thoroughly desaturated by any known means; only anapproximate value may be obtained through desaturation.EThe mass of the saturant shall be not less than 1.4 times the mass of the desaturated (unsaturated) dry felt.D227032