ASTM D330-2007 Standard Specification for 2-Butoxyethanol《2-丁氧基乙醇的标准规范》.pdf

1、Designation: D 330 07Standard Specification for2-Butoxyethanol1, 2This standard is issued under the fixed designation D 330; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicat

2、es the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification covers 2-butoxyethanol.1.2 The following applies to all specif

3、ied limits in thisstandard; for purposes of determining conformance with thisstandard, an observed value or a calculated value shall berounded off “to the nearest unit” in the last right-hand digitused in expressing the specification limit, in accordance withthe rounding-off method of Practice E29.1

4、.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 For specific hazard information and guidance, see thesuppliers Material Safety Data Sheet for materials listed in thisspecification.2. Referenced Documents2.1 ASTM Standards

5、:3D 268 Guide for Sampling and Testing Volatile Solventsand Chemical Intermediates for Use in Paint and RelatedCoatings and MaterialD 1078 Test Method for Distillation Range of VolatileOrganic LiquidsD 1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)D 1364 Test Method for Water in

6、 Volatile Solvents (KarlFischer Reagent Titration Method)D 1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint, Varnish, Lacquer,and Related ProductsD 4052 Test Method for Density and Relative Density ofLiquids by Digital Density MeterD 5386 Test Method for Colo

7、r of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE 300 Practice for Sampling Industrial Chemicals2.2 U.S. Federal Standard:PPP-C-2020 Specification for Packaging of Chemicals, Liq-uid, Dry, and Paste43. Propert

8、ies3.1 2-Butoxyethanol shall conform to the following require-ments:Apparent specific gravity20/20C 0.901 to 0.904or25/25C 0.898 to 0.901Color, Pt-Co scale, max (Note 1)15Distillation range, 760 mm HgInitial boiling point, C, min 168Dry point, C, max 173Water, weight %, max 0.1Acidity (free acid as

9、acetic acid),weight %, max0.01 equivalent to 0.093 mg KOH pergram of material_NOTE 1Instrumental Pt-Co color determined by Test Method D 5386has been shown to have no statistically significant difference from Pt-Cocolor determined by Test Method D 1209. However, it is not knownwhether 2-butoxyethano

10、l was part of the sample set included in theinterlaboratory study.4. Sampling4.1 The material shall be sampled in accordance withPractice E 300.5. Test Methods5.1 The properties enumerated in this specification shall bedetermined in accordance with the following ASTM methods:5.1.1 Apparent Specific

11、GravityDetermine the apparentspecific gravity by any convenient method that is accurate to1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents, Plasticizers, an

12、d Chemical Intermediates.Current edition approved June 1, 2007. Published July 2007. Originally approvedin 1935. Last previous edition approved in 2001 as D 330 93 (2001).2This compound is also known under the name ethylene glycol monobutyl ether.3For referenced ASTM standards, visit the ASTM websit

13、e, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, P

14、A 19111-5098, http:/www.dodssp.daps.mil.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.the third decimal place, the temperature of both specimen andwater being 20 or

15、25C (See Guide D 268 or Test MethodD 4052.)5.1.2 ColorTest Method D 1209 (see Note 1).5.1.3 Distillation RangeTest Method D 1078 using atemperature measuring device having a range of 148 to 202Cand a resolution of 0.1C.5.1.4 WaterTest Method D 1364.5.1.5 AcidityTest Method D 1613.6. Packaging and Pa

16、ckage Marking6.1 Package size to be agreed upon between the purchaserand the supplier.6.2 Packaging shall conform to applicable carrier rules andregulations or when specified shall conform to PPP-C-2020.7. Keywords7.1 ethylene glycol monobutyl ether; 2butoxyethanolSUMMARY OF CHANGESCommittee D01.35

17、has identified the location of selected changes to this standard since the last issue(D 330 - 93 (2001) that may impact the use of this standard. (Approved June 1, 2007.)(1) Added reference to Practice E29in Scope section.(2) Added Practice E29to list of Referenced Documents.(3) Changed specs limits

18、 for apparent specific gravity in 3.1.(4) Added new Note 1 to 3.1.(5) Added Test Method D 5386 to list of Referenced Docu-ments.(6) Referenced new Note 1 in 5.1.2.(7) Revised 5.1.3.(8) Removed Specification E 1 from 2.1.ASTM International takes no position respecting the validity of any patent right

19、s asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any t

20、ime by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will

21、 receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM

22、 International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D330072