ASTM D360-2012 Standard Specification for Shellac Varnishes《虫胶清漆标准规格》.pdf

1、Designation: D360 12Standard Specification forShellac Varnishes1This standard is issued under the fixed designation D360; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates

2、the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers shellac varnish consisting of asolution or “cut” of a specified type and grade of dry lac resinin specially denatured alcohol. Ninety-five pe

3、rcent (190 proof)ethyl alcohol, specially denatured according to Formula No. 1of the Alcohol, Tobacco, and Firearms of the Treasury Dept., isthe solvent most commonly used. However, other speciallydenatured alcohols and proprietary solvents are also used forthis purpose.1.2 The values stated in inch

4、-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2D29 Test Methods for Sampling and Testing Lac Resins3D207 Specification

5、 for Dry Bleached Lac3D237 Specification for Orange Shellac and Other Lacs33. Types, Grades, and Bodies3.1 This specification covers two grades,Aand B, of orangeshellac varnish and two grades, regular and refined, of bleachedlac varnish. Each type and grade may be furnished in verylight, light, medi

6、um, heavy, very heavy, or extra heavy bodyvarnish, as specified.4. Color4.1 The color of shellac varnish shall be no darker than thecolor of a standard varnish of the same nonvolatile mattercontent mutually agreed upon between the purchaser and theseller.NOTE 1Attention is called to the fact that th

7、e purchaser and the sellermust agree upon one of the two methods for determining color appearingin Test Methods D29.5. Drying Time5.1 Shellac varnish shall dry hard in 1 h. Shellac varnisheshaving a body greater than that for a light body varnish shall bethinned to the nonvolatile matter content of

8、a light bodyvarnish. Special conditions for this test may be made by mutualagreement between the purchaser and the seller.6. Body and Cut6.1 The body and cut of the respective types and gradesshall be based on the percent of nonvolatile matter and shallconform to the following minimum requirements:N

9、onvolatile Matter, min,%Bleached,Orange, RegularGrades andA and B RefinedVery light body (3-lb (1.4-kg) cut)varnish28.5 28.0Light body (4-lb (1.8-kg) cut) varnish 35.0 34.5Medium body (4.5-lb (2.0-kg) cut)varnish37.5 37.0Heavy body (5-lb (2.3-kg) cut) varnish 40.0 39.5Very heavy body (6-lb (2.7-kg)

10、cut)varnish44.0 43.5Extra heavy body (8-lb (3.6-kg) cut)varnish51.0 50.5NOTE 2The term “cut” is defined as the number of pounds of dry lacresin (containing only that amount of moisture acceptable for propercutting with the solvent to ensure a satisfactory varnish) that were addedto 1 gal (3.8 L) of

11、specified solvent in manufacturing the varnish.Allowance has, therefore, been made for 2 % maximum moisture andother volatile matter and 3 % insoluble matter in orange shellac, and for6 % moisture and other volatile matter in bleached lac, in arriving at aminimum value. Varnishes of the above specif

12、ied bodies or “cuts” shouldaccordingly conform to the respective minimum requirements specifiedfor nonvolatile matter.7. Properties of Dry Lac7.1 The nonvolatile matter in the varnish shall conform tothe Properties section of Specification D207 and Table 1 ofSpecification D237.1This specification is

13、 under the jurisdiction of the ASTM Committee D01 onPaint and Related Coatings, Materials, and Applications and is the direct responsi-bility of Subcommittee D01.33 on Polymers and Resins.Current edition approved Nov. 1, 2012. Published November 2012. Originallyapproved in 1933. Last previous editio

14、n approved in 1996 as D360 89 (1996)1which was withdrawn January 2010 and reinstated in November 2012. DOI:10.1520/D0360-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, r

15、efer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.8. Package Marking8.1 Shell

16、ac varnish shall be packaged in standard commer-cial containers of the type and size mutually agreed uponbetween the purchaser and the seller. The label of the containershall show the type, grade, body or cut, and date of manufac-ture of the varnish contained therein.9. Test Methods9.1 The sampling

17、and methods of testing shall be conductedin accordance with Test Methods D29.10. Keywords10.1 denatured alcohol; dry lac resin; orange shellac; shellacvarnishASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standa

18、rd. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewe

19、d every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible

20、technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Consh

21、ohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D360 122