1、Designation: D808 11D808 16Standard Test Method forChlorine in New and Used Petroleum Products (HighPressure Decomposition Device Method)1This standard is issued under the fixed designation D808; the number immediately following the designation indicates the year oforiginal adoption or, in the case
2、of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This t
3、est method covers the determination of chlorine in lubricating oils and greases, including new and used lubricatingoils and greases containing additives, and in additive concentrates. Its range of applicability is 0.10.1 m% to 50 m% chlorine. Theprocedure assumes that compounds containing halogens o
4、ther than chlorine will not be present.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.2.1 The preferred units are mass percent.1.3 This standard does not purport to address all of the safety concerns, if any, associated
5、 with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use. Attention is called to specific warning statements incorporated in the test method.2. Referenced Documents2.
6、1 ASTM Standards:2D1193 Specification for Reagent WaterD4057 Practice for Manual Sampling of Petroleum and Petroleum ProductsD4177 Practice for Automatic Sampling of Petroleum and Petroleum ProductsD6299 Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate
7、Analytical Measure-ment System Performance3. Summary of Test Method3.1 The sample is oxidized by combustion in a high pressure decomposition device containing oxygen under pressure.(WarningStrict adherence to all of the provisions prescribed hereinafter ensures against explosive rupture of the high
8、pressuredecomposition device, or a blow-out, provided the high pressure decomposition device is of proper design and construction andin good mechanical condition. It is desirable, however, that the high pressure decomposition device be enclosed in a shield of steelplate at least 13 mm 13 mm (12 in.)
9、 in.) thick, or equivalent protection be provided against unforeseeable contingencies.) Thechlorine compounds thus liberated are absorbed in a sodium carbonate solution and the amount of chlorine present is determinedgravimetrically by precipitation as silver chloride.4. Significance and Use4.1 This
10、 test method may be used to measure the level of chlorine-containing compounds in petroleum products. Thisknowledge can be used to predict performance or handling characteristics of the product in question.4.2 This test method can also serve as a qualitative tool for the presence or non-detection of
11、 chlorine in petroleum products.In light of the efforts in the industry to prepare chlorine free products, this test method would provide information regarding thechlorine levels, if any, in such products.1 This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products Produc
12、ts, Liquid Fuels, and Lubricants and is the direct responsibility ofSubcommittee D02.03 on Elemental Analysis.Current edition approved Oct. 1, 2011June 1, 2016. Published October 2011June 2016. Originally approved in 1944. Last previous edition approved in 20052011 asD808D808 11.05. DOI: 10.1520/D08
13、08-11.10.1520/D0808-16.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard
14、and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases onl
15、y the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Apparatus5.1 High
16、Pressure Decomposition Device, having a capacity of not less than 300 mL, 300 mL, so constructed that it will notleak during the test, and that quantitative recovery of the liquids from the high pressure decomposition device may be readilyachieved. The inner surface of the high pressure decompositio
17、n device may be made of stainless steel or any other material thatwill not be affected by the combustion process or products. Materials used in the high pressure decomposition device assembly,such as the head gasket and lead-wire insulation, shall be resistant to heat and chemical action, and shall
18、not undergo any reactionthat will affect the chlorine content of the liquid in the high pressure decomposition device.5.2 Sample Cup, platinum, 24 mm 24 mm in outside diameter at the bottom, 27 mm 27 mm in outside diameter at the top, 12mm 12 mm in height outside, and weighing 1010 g to 11 g.11 g.5.
19、3 Firing Wire, platinum, No. 26 B high pressure decomposition deviceAPPENDIX(Nonmandatory Information)X1. QUALITY CONTROLX1.1 Confirm the performance of the instrument or the test procedure by analyzing a QC sample.X1.2 Prior to monitoring the measurement process, the user of the method needs to det
20、ermine the average value and control limitsof the QC sample (see Practice D6299 and MNL 7).5X1.3 Record the QC results and analyze by control charts or other statistically equivalent techniques to ascertain the statisticalcontrol status of the total testing process (see Practice D6299 and MNL 7).5 A
21、ny out-of-control data should trigger investigationfor root cause(s).X1.4 In the absence of explicit requirements given in the test method, the frequency of QC testing is dependent on the criticalityof the quality being measured, the demonstrated stability of the testing process, and customer requir
22、ements. Generally, a QCsample is analyzed each testing day with routine samples. The QC frequency should be increased if a large number of samples areroutinely analyzed. However, when it is demonstrated that the testing is under statistical control, the QC testing frequency maybe reduced. The QC sam
23、ple precision should be checked against the ASTM method precision to ensure data quality.X1.5 It is recommended that, if possible, the type of QC sample that is regularly tested be representative of the material routinelyanalyzed. An ample supply of QC sample material should be available for the int
24、ended period of use, and must be homogenousand stable under the anticipated storage conditions. See Practice D6299 and MNL 75 for further guidance on QC and ControlCharting techniques.SUMMARY OF CHANGESSubcommittee D02.03 has identified the location of selected changes to this standard since the las
25、t issue(D808D808 1105) that may impact the use of this standard. (Approved June 1, 2016.)(1) Replaced the wordAdded Practice D4177 “bomb” throughout the test method withto Referenced Documents; revisedsubsection 7.1 the phrase “high pressure decomposition device.”to include the additional sampling p
26、rocedure.(2) Added new subsection 6.9 for a new reagent.5 MNL 7, Manual on Presentation of Data Control Chart Analysis, 6th ed., ASTM International, W. Conshohocken, PA.D808 165ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item ment
27、ionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee
28、and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting
29、of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Bo
30、x C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 166
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1