ImageVerifierCode 换一换
格式:PDF , 页数:4 ,大小:71.46KB ,
资源ID:512314      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-512314.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D852-2002 Standard Test Method for Solidification Point of Benzene《苯凝固点的标准试验方法》.pdf)为本站会员(lawfemale396)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D852-2002 Standard Test Method for Solidification Point of Benzene《苯凝固点的标准试验方法》.pdf

1、Designation: D 852 02Standard Test Method forSolidification Point of Benzene1This standard is issued under the fixed designation D 852; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthe

2、ses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope *1.1 This test method covers the determination of the solidi-fication point of benzene.1.2 In determining the conformance of the test results usingthis met

3、hod to applicable specifications, results shall berounded off in accordance with the rounding-off method ofPractice E 29.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-p

4、riate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For specific hazardstatements, see Section 7.2. Referenced Documents2.1 ASTM Standards:D 1015 Test Method for Freezing Points of High-PurityHydrocarbons2D 1016 Test Method for Purity of Hydroca

5、rbons fromFreezing Points2D 1193 Specification for Reagent Water3D 3437 Practice for Sampling and Handling Liquid CyclicProducts4E 1 Specification for ASTM Thermometers5E 29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications6E 691 Practice for Conducting a

6、n Interlaboratory Study toDetermine the Precision of a Test Method62.2 Other Document:OSHA Regulations, 29CFR, paragraphs 1910.1000 and1910.120073. Terminology3.1 Definitions:3.1.1 solidification pointan empirical constant defined asthe temperature at which the liquid phase of a substance is inappro

7、ximate equilibrium with a relatively small portion of thesolid phase.3.1.1.1 DiscussionSolidification point is distinguishedfrom freezing point which is described in Test Method D 1015.An interpretation of mol percent purity in terms of freezingpoint is given in Test Method D 1016.4. Summary of Test

8、 Method4.1 Solidification point is measured by noting the maximumtemperature reached during a controlled cooling cycle after theappearance of a solid phase.5. Significance and Use5.1 This test method may be used as a criteria for determin-ing the purity of benzene. The closer the solidification poin

9、treaches that of pure benzene, the purer the sample.6. Apparatus6.1 Benzene Container (Air Jacketed):6.1.1 Inner Container, a test tube 15 mm in outside diameterand 125 mm in length.6.1.2 Air Jacket, a standard test tube 25 mm in outsidediameter and 150 mm in length.6.1.3 Insulation Dry absorbent co

10、tton or glass wool.6.2 Benzene Container (thick walled), a glass test tube 18mm in outside diameter, 14 mm in inside diameter and 150 mmin length. The thick walled tube is only compatible with thethermistor.6.3 Ice Bath, a 1-L beaker, or similar suitable container,having an effective depth of at lea

11、st 127 mm and filled withchipped or shaved ice.6.4 Stirrer, consisting of a 1-mm wire (copper or stainlesssteel) or a 2-mm glass rod with one end bent into a circularform at right angles to the shaft so that it will move freely inthe annular space between the thermometer stem and the wallof the smal

12、ler test tube.6.5 Temperature Measurement Device, either device de-scribed below has been found satisfactory.6.5.1 Thermometer, an ASTM Benzene Freezing Point1This test method is under the jurisdiction of ASTM Committee D16 onAromatic Hydrocarbons and Related Chemicals and is the direct responsibili

13、ty ofSubcommittee D16.01 on Benzene, Toluene, Xylenes, Cyclohexane, and TheirDerivatives.Current edition approved Aug. 10, 2002. Published October 2002. Originallypublished as D 852 45. Last previous edition D 852 00e1.2Annual Book of ASTM Standards, Vol 05.01.3Annual Book of ASTM Standards, Vol 11.

14、01.4Annual Book of ASTM Standards, Vol 06.04.5Annual Book of ASTM Standards, Vol 14.03.6Annual Book of ASTM Standards, Vol 14.02.7Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.1*A Summary of Changes section app

15、ears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Thermometer having a range from 4.0 to 6.0C and conform-ing to the requirements for Thermometer 112C as prescribed inSpecification E 1.6.5.2 Thermistor,

16、Type CSP with accuracy of 0.01 C witha nominal resistance at 2500 s at 25C. The thermistor shall beequipped with an ohm meter capable of reading resistance tothe nearest 0.1 s.6.6 Stirring Apparatus (Optional), the apparatus illustratedin Fig. 1 has been demonstrated to be an acceptable replace-ment

17、 for manually stirring the benzene solution.7. Hazards7.1 Consult the latest OSHA regulations, suppliers MaterialSafety Data Sheets, and local regulations for all materials usedin this test method.8. Sampling8.1 Sample the material in accordance with PracticeD 3437.9. Preparation of Apparatus9.1 Fit

18、 the benzene container with a two-hole stopper.Through one hole insert the temperature measurement device.The thermometer should be inserted up to the 4.0C mark. Thethermistor should be inserted so as to contact the benzenesolution. Through the other hole insert the shaft of the stirrer.9.2 If using

19、 the benzene container (air jacketed), place a18-in. (3.2-mm) layer of dry absorbent cotton or glass wool inthe bottom of the larger test tube and insert the inner containerup to the lip into a stopper or annular ring that just fits into themouth of the air jacket.10. Calibration of Temperature Meas

20、uring Device10.1 Calibration of ASTM thermometer 112C is accom-plished with the small scale etched on the lower portion of thethermometer. Prepare an ice bath by filling a small Dewar flaskwith crushed ice made from Type I or Type II water (asspecified in Specification D 1193) and add just enough ch

21、illedType I or Type II water to make a slurry. Immerse theFIG. 1 Benzene Solidification Point Apparatus Set UpD852022thermometer in the ice bath, allow 5 min for the system toreach equilibrium and read the thermometer. Solidificationpoint values are subsequently adjusted by adding (or subtract-ing)

22、the number of degrees the thermometer is below (orabove) 0.00C.10.2 Calibration of the thermistor is performed by thethermistor manufacturer. Resistance is converted to tempera-ture using an equation supplied by the manufacturer.11. Procedure11.1 Saturate the sample of benzene with water as follows:

23、Place 7 to 8 mL of the sample in the benzene container, add 1drop of water, and shake the tube and contents vigorously.11.2 Place the stopper and stirring apparatus (if any) into thebenzene container.11.3 When using the benzene container (air jacket), theoperator may cool the smaller test tube and c

24、ontents rapidly toabout 6C in the ice bath, while stirring. Wipe dry the outsideof the smaller test tube and insert it into the larger test tube.Place the assembled tubes in the ice bath.11.4 Stir the benzene continuously and observe the tempera-ture closely. The temperature will fall to a minimum,

25、then riseto a maximum, remain constant at this maximum for approxi-mately 15 s, and then fall again (Note 1). The minimumtemperature is due to super-cooling before solidification startsand shall not be more than 0.7C below the maximum whenusing a thermometer. Record the maximum constant tempera-ture

26、 observed to the nearest 0.01C and designate it as “wet”(Note 1).NOTE 1If distinct minimum and maximum points are not evident, orif the temperature does not remain constant at the maximum for at least 15s, the determination shall be repeated. The thermistor reading shouldremain constant to at least

27、two places to the right of the decimal.12. Report12.1 Results shall be reported on the anhydrous basis. Sincethe determination is actually made on water-saturated benzene,the solidification point shall be corrected to the anhydrous basisby adding 0.09C to the observed maximum temperaturefollowing th

28、e minimum. Corrections for accuracy of thethermometer shall be made.13. Precision and Bias813.1 Thermometer PrecisionThe following criteriashould be used to judge the acceptability of results obtained bythis test method when using a thermometer. The criteria weredetermined by measuring the solidific

29、ation point of a sampletwelve times at one laboratory using a thermometer. Duplicateresults in the same laboratory should not be considered suspectunless they differ by more than 0.04C.13.2 Thermistor PrecisionThe following criteria shouldbe used to judge the acceptability (95 % probability level) o

30、fresults obtained by this test method when using a thermistor.The criteria were derived from an interlaboratory study be-tween six laboratories. Three different samples were analyzedin triplicate on two different days using a thermistor and a thickwalled glass test tube.13.2.1 Intermediate Precision

31、 Results in the same labo-ratory should not be considered suspect unless they differ morethan 0.04C. On the basis of test error alone, the differencebetween two results obtained in the same laboratory on thesame material will be expected to exceed this value only 5 %of the time.13.2.2 Reproducibilit

32、yResults submitted by each of twolaboratories should not be considered suspect unless they differby more than 0.05C. On the basis of test error alone, thedifference between two test results obtained in different labo-ratories on the same material will be expected to exceed thisvalue only5%ofthetime.

33、13.3 BiasSince there is no accepted reference materialsuitable for determining the bias for the procedure, bias has notbeen determined.14. Keywords14.1 benzene; solidification pointSUMMARY OF CHANGESCommittee D16 has identified the location of selected changes to this standard since the last date of

34、 issue(D 852 - 00e1) that may impact the use of this standard.(1) Correction of bath temperature and generalization oftemperature measuring device in Fig. 1.2) Addition of new Precision statements for thermometer andthermistor.ASTM International takes no position respecting the validity of any paten

35、t rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision a

36、t any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your commen

37、ts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.8Supporting data are availabl

38、e for ASTM International Headquarters. RequestRR: D161028.D852023This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D852024

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1