ASTM D964-2003(2014) Standard Specification for Metallic Copper Powder for Use in Antifouling Paints《防污涂料用金属铜粉的标准规格》.pdf

1、Designation: D964 03 (Reapproved 2014)Standard Specification forMetallic Copper Powder for Use in Antifouling Paints1This standard is issued under the fixed designation D964; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers copper powder for use inantifouling paints.1.2 The values stated in inch-pound units are

3、 to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2D185 Test Methods for Coarse Particles in PigmentsD283 Test Methods for Chemical Analys

4、is of CuprousOxide and Copper Pigments3. Composition3.1 The pigment shall consist essentially of finely dividedcopper metal and shall conform to the following requirements:Copper, min, (Percent) 99Coarse particles, 325 Mesh, max, (Percent) 1.04. Sampling4.1 Two samples shall be taken at random from

5、differentpackages from each lot, batch, days pack, or other unit ofproduction in a shipment. When no markings distinguishingbetween units of production appear, samples shall be takenfrom different packages in the ratio of two samples for each 10000 lb (5000 kg), except that for shipments of less tha

6、n 10 000lb two samples shall be taken. At the option of the purchaser,the samples may be tested separately or after blending in equalquantities the samples from the same production unit to form acomposite sample.5. Test Methods5.1 Tests shall be conducted in accordance with the follow-ing ASTM test

7、methods:5.1.1 CopperTest Methods D283.5.1.2 Coarse ParticlesTest Methods D185.6. Keywords6.1 antifouling paint; copper pigment; copper powderASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this

8、 standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five year

9、s andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committ

10、ee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428

11、-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the stan

12、dard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.

13、31 on Pigment Specifications.Current edition approved Dec. 1, 2014. Published December 2014. Originallyapproved in 1948. Last previous edition approved in 2008 as D964 03 (2008)1.DOI: 10.1520/D0964-03R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1