ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:130.36KB ,
资源ID:512599      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-512599.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D968-2016 Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive《用落磨料测定有机涂层耐磨性的标准试验方法》.pdf)为本站会员(lawfemale396)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D968-2016 Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive《用落磨料测定有机涂层耐磨性的标准试验方法》.pdf

1、Designation: D968 16Standard Test Methods forAbrasion Resistance of Organic Coatings by FallingAbrasive1This standard is issued under the fixed designation D968; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revi

2、sion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 These test methods cover the determinati

3、on of theresistance of organic coatings to abrasion produced by abrasivefalling onto coatings applied to a plane rigid surface, such as ametal or glass panel.1.2 Two test methods based on different abrasives arecovered as follows:SectionsMethod AFalling Sand Abrasion Test 613Method BFalling Silicon

4、Carbide Abrasion Test 14211.3 These methods should be restricted to testing in onlyone laboratory when numerical values are used because of thepoor reproducibility of the methods (see 13.1.2 and 21.1.2).Interlaboratory agreement is improved significantly when rank-ing is used in place of numerical v

5、alues.1.4 The values stated in SI units are to be regarded as thestandard with the exception of mils when determining coatingthickness. The values given in parentheses are for informationonly.1.5 This standard does not purport to address the safetyconcerns, if any, associated with its use. It is the

6、 responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D823 Practices for Producing Films of Uniform Thicknessof Paint, Varnish, and Related Produ

7、cts on Test PanelsD1005 Test Method for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD7091 Practice for Nondestructive Measurement of DryFilm Thickness of Nonmagnetic Coatings Applied toFerrous Metals and Nonmagnetic, Nonconductive Coat-ings Applied to Non-Ferrous MetalsE1

8、1 Specification for Woven Wire Test Sieve Cloth and TestSieves2.2 Other Standards:ANSI B74.12 Specifications for the Size of Abrasive Grain Grinding Wheels, Polishing and General IndustrialUses3FEPA Standard 42-2:2006 Grains of Fused AluminumOxide, Silicon Carbide and other Abrasive Materials forBon

9、ded Abrasives and for General Applications Mi-crogrits F230 to F200043. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 abrasion resistance, nthe amount of abrasive re-quired to wear through a unit film thickness of the coating.4. Summary of Test Method4.1 Abrasive is allowed to

10、fall from a specified heightthrough a guide tube onto a coated panel until the substratebecomes visible. The amount of abrasive per unit film thick-ness is reported as the abrasion resistance of the coating on thepanel. Silica sand or silicon carbide may be used, as specified.5. Significance and Use

11、5.1 Silica sand produces a slower rate of abrasion fororganic coatings than that provided by silicon carbide. Forsome types of coatings, it may also provide greater differen-tiation.5.2 The abrasion resistance scales produced by the twomethods differ, but the methods provide approximately thesame ra

12、nkings of coatings for abrasion resistance.1These test methods are under the jurisdiction of ASTM Committee D01 onPaint and Related Coatings, Materials, and Applications and are the directresponsibility of Subcommittee D01.23 on Physical Properties of Applied PaintFilms.Current edition approved Dec.

13、 1, 2016. Published January 2017. Originallyapproved in 1948. Last previous edition approved in 2015 as D968 15. DOI:10.1520/D0968-16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume info

14、rmation, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Federation of European Producers of Abrasives (FEPA), 20 av.,Reille, Paris, F-75014,

15、 www.fepa-.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardi

16、zation established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.3 Each of the methods has been found useful for rating theabrasion resistance of specific t

17、ypes of coatings. For exampleMethod A (falling sand) has been used for rating floor coatingswhile Method B (falling silicon carbide) has been used forrating coatings for ship decks.METHOD AFALLING SAND ABRASION TEST56. Apparatus and Materials6.1 Abrasion Tester, as illustrated in Fig. 1 and Fig. 2.A

18、gatefor starting the flow of abrasive is located near the top of theguide tube. It consists of a metal disk inserted into a slit in theside of the guide tube with a collar covering the slit. The guidetube shall be firmly supported in a vertical position over asuitable receptacle, which shall contain

19、 a support for holdingthe coated panel at an angle of 45 to the vertical. The openingof the tube is directly above the area to be abraded and thedistance from the tube to the coated surface face at the nearestpoint is 25 mm (1 in.) when measured in the vertical direction.The base of the apparatus sh

20、all be fitted with adjusting screwsfor properly aligning the equipment.6.2 Standard AbrasiveNatural silica sand from the St.Peters or Jordan sandstone deposits (located in the centralUnited States) shall be considered standard when graded asfollows after 5 min of continuous sieving. Use the sievesde

21、scribed in Specification E11.0 % retained on a No. 16 (1.18 mm) sieveMaximum 15 % retained on a No. 20 (850 m) sieveMinimum 80 % retained on a No. 30 (600 m) sieveMaximum 5 % passing a No. 30 (600 m) sieveThe sand is characterized by its grain shape and has a silicondioxide content greater than 99 %

22、.NOTE 1The abrading qualities of sand obtained from different sourcesmay differ slightly even though the sand meets the sieve requirements.Therefore, for maximum precision of test results, purchaser and sellershould use sand from the same source.7. Test Specimens7.1 Apply uniform coatings of the mat

23、erial to be tested to aplane, rigid surface such as a metal or glass panel. Prepare aminimum of two coated panels for the material.7.2 Cure the coated panels under the conditions of humidityand temperature agreed upon between the purchaser and seller.NOTE 2The coatings should be applied in accordanc

24、e with PracticesD823, or as agreed upon between the purchaser and the seller.NOTE 3The thickness of the dry coatings should be measured inaccordance with Test Methods D1005 or D7091.NOTE 4While the minimum of two coated panels is acceptable,evaluating three or more panels per material will provide g

25、reater confi-dence in your test results.5Hipkins, C. C., and Phain, R. J., “The Falling Sand Abrasion Tester,” ASTMBulletin, No. 143, December 1946, pp. 1822.FIG. 1 Apparatus for Falling Sand Abrasion TestNOTE 1All dimensions are given in inches. 1 in. = 25.4 mm.FIG. 2 Design Details of Abrasion Tes

26、t ApparatusD968 1628. Standardization8.1 Pour a quantity of standard sand into the funnel andexamine the sand stream falling from the lower end of theguide tube. Align the apparatus by means of the adjustingscrews in the base until the inner concentrated core of the sandstream falls in the center of

27、 the flow when viewed at twopositions at 90 to each other. Introduce a measured volume ofsand (2000 6 10 mL is a convenient amount) and determinethe time of efflux. The rate of flow shall be 2 L of sand in 21to 23.5 s.8.2 Secure a trial panel in the testing position, as describedin 6.1, and introduc

28、e the sand in increments until a spot 4 mm(532 in.) in diameter is worn through to the base material. Theoverall abraded area shall be elliptical in shape, about 25 mm(1 in.) in width and 30 mm (114 in.) in length. The center of thearea of maximum abrasion shall be on the centerline throughthe longe

29、r axis of the abraded pattern and within 14 to 17 mm(916 to1116 in.) of the top edge. Slight final adjustment of theinstrument may be required to center the abrasion spot in thepattern.8.3 A final check on alignment is made by determining theamount of sand that passes through a 4-mm (532-in.) hole i

30、n ametal panel placed directly under the tube. Place a containerunder the hole in the panel and allow a weighed amount of sandto pass through the tube onto the panel. Weigh the amount ofsand that passed through the hole into the container. Theapparatus can be considered to be in calibration if the a

31、mountof sand that passed through the hole is 90 to 93 % of theamount of sand that impinged on the panel.9. Conditioning9.1 Unless otherwise agreed upon between purchaser andseller, condition the coated test panels for at least 24 h at 23 62C and 50 6 5 % relative humidity. Conduct the test in thesam

32、e environment or immediately on removal therefrom.10. Procedure10.1 On each coated panel mark three circular areas, eachapproximately 25 mm (1 in.) in diameter, and so arranged thateach can be properly positioned in the panel support of theabrasion tester. Measure the thickness of the coating by Tes

33、tMethods D1005 or D7091 in at least three locations in eacharea. Record the mean of each set of measurements as thethickness of the coating over the respective area.10.2 After conditioning, secure the coated panel in the testeras described in 6.1. Adjust the panel so that one of the markedareas will

34、 be centered under the guide tube.10.3 Pour standard sand, measured volumetrically, into thefunnel. Withdraw the gate and allow the sand to flow throughthe guide tube and impinge on the coated panel. Collect thesand in a container located at the bottom of the tester. Repeatthis operation until a 4-m

35、m (532-in.) diameter area of thecoating has worn through to the substrate. A convenientincrement of sand to employ during the test is 2000 6 10 mL.As the end-point is approached, increments of 200 6 2mLmay be introduced into the funnel.NOTE 5When the gate is withdrawn from the guide tube, make certa

36、inthat a collar covers the slit opening in the tube.10.4 Abrade each of the remaining marked-off areas of thecoated panel as outlined in 10.2.NOTE 6Check the alignment of the guide tube at frequent intervals toensure that the concentrated inner core of the sand stream is falling in thecenter of the

37、flow.NOTE 7After 25 passes through the apparatus, resieve the sand witha No. 30 sieve to remove fines. Replace the sand after 50 passes.10.5 Repeat 10.1 10.4 on at least one additional panelcoated with the material under test.11. Calculation11.1 For each area of the coated panel tested, calculate th

38、eabrasion resistance, A, in litres per mil from the followingequation:Avolume5 V/T (1)where:V = volume of abrasive used, L (to one decimal place) andT = thickness of coating, mils (to one decimal place).11.2 Calculate the mean of the abrasion resistance valuesobtained for different areas of the coat

39、ed panel and the meanvalue of the replicate panels.12. Report12.1 Report the following information for each coated paneltested:12.1.1 Temperature and humidity during curing and at thetime of testing,12.1.2 Type and source of abrasive,12.1.3 Litres of abrasive used for each area tested,12.1.4 Wear pa

40、ttern measurements, if different than 8.2,12.1.5 Coating thickness in mils for each area tested,12.1.6 Abrasion resistance values for each area tested,12.1.7 Mean abrasion resistance for each coated paneltested, and12.1.8 Mean abrasion resistance and range of the replicatecoated panels.13. Precision

41、613.1 On the basis of an interlaboratory test of this testmethod in which three laboratories tested four types of coatingsdiffering in their abrasion resistance, the within-laboratorycoefficient of variation was found to be 9 % with 22 df and thebetween-laboratories coefficient of variation 35 % wit

42、h 7 df.Based on these coefficients, the following criteria should beused for judging the acceptability of results at the 95 %confidence level.13.1.1 RepeatabilityTwo results, each the mean of threeruns, obtained by the same operator should be consideredsuspect if they differ by more than 25 % of the

43、ir mean value.13.1.2 ReproducibilityTwo results, each the mean of threeruns, obtained by operators in different laboratories should beconsidered suspect if they differ by more than 118 % of theirmean value.6Supporting data have been filed at ASTM International Headquarters and maybe obtained by requ

44、esting Research Report RR:D01-1037. ContactASTM CustomerService at serviceastm.org.D968 163NOTE 8The reproducibility of this test is improved substantially whenrankings of the coatings by magnitude of abrasion resistance are used. Inthe interlaboratory test for evaluating precision, all laboratories

45、 ranked thecoatings in the same order.13.2 BiasAt the time of the study, there was no acceptedreference material suitable for determining bias for this testmethod, therefore no statement on bias is being made.METHOD BFALLING SILICON CARBIDE TEST14. Apparatus and Materials14.1 Abrasion Tester, as des

46、cribed in 6.1, with two excep-tions:14.1.1 A metal washer with an opening of 8.5 6 0.1 mm iscentered in the bottom opening of the funnel to restrict the flowof the abrasive.14.1.2 The disk gate installed in a slit at the top of the guidetube may be replaced by a gate in the bottom of the funnel. Thi

47、sgate consists of a solid metal disk attached to a long verticalscrew and mounted above the washer.14.2 Standard AbrasiveSilicon carbide grain shall beconsidered standard when graded as follows after 5 min ofcontinuous sieving:0 % retained on a No. 10 (2.00 mm) sieveMaximum of 20 % retained on a No.

48、 14 (1.40 mm) sieveMinimum of 45 % retained on a No. 16 (1.18 mm) sieveMinimum of 70 % retained on a No. 16 (1.18 mm) and No. 18(1.00 mm) sieve3 % Maximum passes a No. 20 (850 m) sieveThese grading requirements correspond to No. 16 grit inaccordance with ANSI B74.12. These grading requirementsalso c

49、orrespond to F16 grit in accordance with FEPA Standard42-2:2006.14.2.1 Use the sieves described in Specification E11.15. Test Specimens15.1 Prepare the coated panels as outlined in 7.1 and 7.2.16. Standardization16.1 Standardize the abrasion tester by the procedures givenin 8.1 8.3, with the following exceptions:16.1.1 Use silicon carbide grain where sand is specified.16.1.2 Weigh the volume of silicon carbide grain to beintroduced into the tester. Determine the efflux time for thisvolume. The rate of flow shall be 10 61 g/s

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1