ASTM D2467-2015 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings Schedule 80《聚氯乙烯 (PVC) 塑料管配件 (表单80) 的标准规格》.pdf

1、Designation: D2467 13aD2467 15Standard Specification forPoly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule801This standard is issued under the fixed designation D2467; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the yea

2、r of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers

3、poly(vinyl chloride) (PVC) Schedule 80 pipe fittings. Included are requirements for materials,workmanship, dimensions, and burst pressure.NOTE 1CPVC plastic pipe fittings, which were formerly included in this standard, are now covered in Specification F439.1.2 The products covered by this specificat

4、ion are intended for use with the distribution of pressurized liquids only, which arechemically compatible with the piping materials. Due to inherent hazards associated with testing components and systems withcompressed air or other compressed gases, some manufacturers do not allow pneumatic testing

5、 of their products. Consult withspecific product/component manufacturers for their specific testing procedures prior to pneumatic testing.NOTE 2Pressurized (compressed) air or other compressed gases contain large amounts of stored energy, which present serious safety hazards shoulda system fail for

6、any reason.1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notesand footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.1.4 The values stated in inch-pound units are t

7、o be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification.This standarddo

8、es not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Stan

9、dards:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology for Abbreviated Terms Relating to PlasticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorina

10、ted Poly(Vinyl Chloride) (CPVC)CompoundsD1785 Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and FittingsD2749 Symbols for Dimensions of Plastic Pipe FittingsF412 Terminology Relating to Plastic P

11、iping SystemsF439 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings2.2 Federal Standard:3Fed. Std. No. 123 Marking for Shipment (Civil Agencies)1 This specification is under t

12、he jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved Aug. 1, 2013March 1, 2015. Published September 2013March 2015. Originally approved in 1965. Last previous edition approved in 2013 asD2467 13.D

13、2467 13a. DOI: 10.1520/D2467-13A10.1520/D2467-152 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available f

14、rom Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.DLADocument Services Building 4/D 700 Robbins Avenue Philadelphia, PA 19111-5094 http:/quicksearch.dla.mil/This document is not an ASTM standard and is inten

15、ded only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the curren

16、t versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States12.3 National Sanitation Foundatio

17、n Standards:4Standard No. 14 for Plastic Piping Components and Related MaterialsStandard No. 61 for Drinking Water Systems ComponentsHealth Effects3. Terminology3.1 GeneralDefinitions are in accordance with Terminology F412 and abbreviations are in accordance with TerminologyD1600, unless otherwise

18、indicated. The abbreviation for poly(vinyl chloride) plastic is PVC.4. Classification4.1 GeneralThis specification covers Schedule 80 PVC pipe fittings, socket-type, made from four PVC plastic compoundsand intended for use with Iron Pipe Size (IPS) outside-diameter plastic pipe. (See Specification D

19、1785.)4.1.1 Fittings covered by this specification are normally molded. In-line fittings, such as couplings, unions, bushings, caps,nipples, and the like, shall be molded or machined from extruded stock.4.1.2 Fittings fabricated by back welding or butt fusion are not included in this specification.5

20、. Materials and Manufacture5.1 This specification covers PVC pipe fittings made from five PVC plastics as classified in Specification D1784.These are PVC12454, 11443, and 14333.5.2 CompoundThe PVC plastic compound shall meet the requirements of PVC 12454, 11443, or 14333, as described inSpecificatio

21、n D1784.5.3 Rework MaterialThe manufacturers shall use only their own clean rework fitting material and the fittings produced shallmeet all the requirements of this specification.6. Requirements6.1 Dimensions and Tolerances:6.1.1 Fitting sockets inside diameters (waterways), minimum wall thicknesses

22、, and dimensions shall be as shown in Tables 1-5when measured in accordance with Test Method D2122.6.1.2 When multistep reducer bushings are cored out, the inner socket shall be reinforced from the outer wall by a minimumof three ribs extending from the top of the inner socket to the deepest extremi

23、ty of the coring. The transition from D to DJ (Table4) shall be straight, tapered as shown, or radiused. A positive taper in the same direction of the taper in the socket on the outsidediameter of the bushing is optional (see XA/XB in Table 3). Any point measured along the outside diameter of the bu

24、shing(between points XA and XB) shall not fall below minimum pipe OD.6.1.3 The minimum wall thickness of fittings shall be 125 % of the minimum wall thickness of the corresponding size ofSchedule 80 pipe for which they are designed to be used, except that for the socket, the wall thickness shall be

25、at least equal tothe minimum wall thickness of the corresponding size of Schedule 80 pipe.6.1.4 The minimum inside diameter of the fittings shallbe not less than the minimum specified inside diameter of the corresponding size of Schedule 80 pipe. This is calculated as follows:minimum OD!223maximum w

26、all!5minimum ID (1)6.1.5 Minimum dimensions have zero negative tolerance. Tolerances on other dimensions are shown in Table 1 and Table 3.6.2 ThreadsFor all fittings having taper pipe threads, threads shall conform to Specification F1498 and be gaged in accordancewith 8.4.6.3 Burst Pressure:6.3.1 Th

27、e minimum burst strength of the fittings shall be not less than that calculated for the size and wall thickness of the pipewith which it is to be used, when calculated from the following equation and using a stress of 6400 psi for 8-in. and smaller fittings,and a stress of 5100 psi for fittings larg

28、er than 8-in. when the cell class is 12454, 13354 and 11443. When the cell class is 14333a stress of 5000 psi is used in the equation for fittings 8-in. and smaller:S 5PDO 2t!/2t (2)S 5 hoop stress, psi MPa!P 5 internal pressure, psi MPa!,Do 5 average outside diameter, in. mm!,andt 5 minimum wall th

29、ickness, in. mm!Fittings tested in accordance with 8.5 shall withstand the minimum burst pressure shown in Table 6.4 Available from NSF International, P.O. Box 130140, 789 N. Dixboro Rd., Ann Arbor, MI 48113-0140, http:/www.nsf.org.D2467 152TABLE 1 Tapered Sockets for PVC Pipe Fittings, Schedule 80,

30、 in. (mm)ANominalPipe SizeASocket Entrance DiameterBSocket Bottom Diameter CBSocketLength, minDCInsideDiameter, minWall Thickness, min Entrance, minDiameterTolerance onNominalDiameterMax Out-of-Round DiameterTolerance onNominalDiameterMax Out-of-Round E F EW EX EZ18 0.417 (10.59) 0.004 (0.10) 0.016

31、(0.41) 0.401 (10.18) 0.004 (0.10) 0.016 (0.41) 0.500 (12.7) 0.171 (4.34) 0.095 (2.41) 0.118 (3.00) 164 (0.40) 164 (0.40) 164 (0.40)14 0.552 (14.02) 0.004 (0.10) 0.016 (0.41) 0.536 (13.61) 0.004 (0.10) 0.016 (0.41) 0.625(15.88)0.258 (6.55) 0.119 (3.02) 0.149 (3.78) 164 (0.40) 164 (0.40) 164 (0.40)38

32、0.687 (17.45) 0.004 (0.10) 0.016 (0.41) 0.671 (17.04) 0.004 (0.10) 0.016 (0.41) 0.750(19.05)0.379 (9.63) 0.126 (3.20) 0.160 (4.06) 132 (0.79) 132 (0.79) 132 (0.79)12 0.848 (21.54) 0.004 (0.10) 0.016 (0.41) 0.836 (21.23) 0.004 (0.10) 0.016 (0.41) 0.875(22.22)0.502 (12.75) 0.147 (3.73) 0.185 (4.70) 13

33、2 (0.79) 132 (0.79) 132 (0.79)34 1.058 (26.87) 0.004 (0.10) 0.020 (0.51) 1.046 (26.57) 0.004 (0.10) 0.020 (0.51) 1.000(25.40)0.698 (17.73) 0.154 (3.91) 0.195 (4.95) 132 (0.79) 132 (0.79) 132 (0.79)1 1.325 (33.65) 0.005 (0.13) 0.020 (0.51) 1.310 (33.27) 0.005 (0.13) 0.020 (0.51) 1.125(28.58)0.911 (23

34、.14) 0.179 (4.55) 0.225 (5.72) 116 (1.59) 116 (1.59) 116 (1.59)114 1.670 (42.42) 0.005 (0.13) 0.024 (0.61) 1.655 (42.04) 0.005 (0.13) 0.024 (0.61) 1.250(31.75)1.227 (31.17) 0.191 (4.85) 0.239 (6.07) 116 (1.59) 116 (1.59) 116 (1.59)112 1.912 (48.56) 0.006 (0.15) 0.024 (0.61) 1.894 (48.11) 0.006 (0.15

35、) 0.024 (0.61) 1.375(34.93)1.446 (36.73) 0.200 (5.08) 0.250 (6.35) 116 (1.59) 116 (1.59) 116 (1.59)2 2.387 (60.63) 0.006 (0.15) 0.024 (0.61) 2.369 (60.17) 0.006 (0.15) 0.024 (0.61) 1.500(38.10)1.881 (47.78) 0.218 (5.54) 0.275 (6.99) 116 (1.59) 116 (1.59) 116 (1.59)212 2.889 (73.38) 0.007 (0.18) 0.03

36、0 (0.76) 2.868 (72.85) 0.007 (0.18) 0.030 (0.76) 1.750(44.45)2.250 (57.15) 0.276 (7.01) 0.345 (8.76) 332 (2.38) 18 (3.18) 18 (3.18)3 3.516 (89.31) 0.008 (0.20) 0.030 (0.76) 3.492 (88.70) 0.008 (0.20) 0.030 (0.76) 1.875(47.63)2.820 (71.63) 0.300 (7.62) 0.375 (9.53) 332 (2.38) 18 (3.18) 18 (3.18)312 4

37、.016 (102.01) 0.008 (0.20) 0.030 (0.76) 3.992 (101.4) 0.008 (0.20) 0.030 (0.76) 2.125(53.98)3.280 (83.31) 0.318 (8.08) 0.400 (10.16) 332 (2.38) 18 (3.18) 18 (3.18)4 4.518 (114.76) 0.009 (0.23) 0.030 (0.76) 4.491 (114.1) 0.009 (0.23) 0.030 (0.76) 2.250(57.15)3.737 (94.92) 0.337 (8.56) 0.420 (10.67) 3

38、32 (2.38) 18 (3.18) 18 (3.18)5 5.583 (141.81) 0.010 (0.25) 0.060 (1.52) 5.553 (141.0) 0.010 (0.25) 0.060 (1.52) 2.625(66.68)4.703(119.46)0.375 (9.53) 0.470 (11.94) 332 (2.38) 18 (3.18) 18 (3.18)6 6.647 (168.83) 0.011 (0.28) 0.060 (1.52) 6.614 (168.0) 0.011 (0.28) 0.060 (1.52) 3.000(76.20)5.646(143.4

39、1)0.432 (10.97) 0.540 (13.72) 18 (3.18) 316 (4.76) 316 (4.76)8 8.655 (219.84) 0.015 (0.38) 0.090 (2.29) 8.610 (218.7) 0.015 (0.38) 0.090 (2.29) 4.000(101.60)7.490(190.25)0.500 (12.70) 0.625 (15.88) 18 (3.18) 316 (4.76) 316 (4.76)10 10.780(273.81)0.015 (0.38) 0.100 (2.54) 10.735(272.67)0.015 (0.38) 0

40、.100 (2.54) 5.000(127.00)9.407(238.94)0.593 (15.06) 0.741 (18.82) 18 (3.18) 316 (4.76) 316 (4.76)12 12.780(324.61)0.015 (0.38) 0.120 (3.05) 12.735(323.47)0.015 (0.38) 0.120 (3.05) 6.000(152.40)11.197(284.40)0.687 (17.45) 0.859 (21.82) 18 (3.18) 316 (4.76) 316 (4.76)D2467153TABLE 1 Tapered Sockets fo

41、r PVC Pipe Fittings, Schedule 80, in. (mm)ANominalPipeSizeASocket Entrance DiameterBSocket Bottom Diameter CBSocket Length, minDCInside Diameter,minWall Thickness, min Entrance, minDiameterTolerance onNominalDiameterMax Out-of-Round DiameterTolerance onNominalDiameterMax Out-of-Round E F EW EX EZ18

42、0.417 (10.59) 0.004 (0.10) 0.016 (0.41) 0.401 (10.18) 0.004 (0.10) 0.016 (0.41) 0.500 (12.7) 0.171 (4.34) 0.095 (2.41) 0.118 (3.00) 164 (0.40) 164 (0.40) 164 (0.40)14 0.552 (14.02) 0.004 (0.10) 0.016 (0.41) 0.536 (13.61) 0.004 (0.10) 0.016 (0.41) 0.625 (15.88) 0.258 (6.55) 0.119 (3.02) 0.149 (3.78)

43、164 (0.40) 164 (0.40) 164 (0.40)38 0.687 (17.45) 0.004 (0.10) 0.016 (0.41) 0.671 (17.04) 0.004 (0.10) 0.016 (0.41) 0.750 (19.05) 0.379 (9.63) 0.126 (3.20) 0.160 (4.06) 132 (0.79) 132 (0.79) 132 (0.79)12 0.848 (21.54) 0.004 (0.10) 0.016 (0.41) 0.836 (21.23) 0.004 (0.10) 0.016 (0.41) 0.875 (22.22) 0.5

44、02 (12.75) 0.147 (3.73) 0.185 (4.70) 132 (0.79) 132 (0.79) 132 (0.79)34 1.058 (26.87) 0.004 (0.10) 0.020 (0.51) 1.046 (26.57) 0.004 (0.10) 0.020 (0.51) 1.000 (25.40) 0.698 (17.73) 0.154 (3.91) 0.195 (4.95) 132 (0.79) 132 (0.79) 132 (0.79)1 1.325 (33.65) 0.005 (0.13) 0.020 (0.51) 1.310 (33.27) 0.005

45、(0.13) 0.020 (0.51) 1.125 (28.58) 0.911 (23.14) 0.179 (4.55) 0.225 (5.72) 116 (1.59) 116 (1.59) 116 (1.59)114 1.670 (42.42) 0.005 (0.13) 0.024 (0.61) 1.655 (42.04) 0.005 (0.13) 0.024 (0.61) 1.250 (31.75) 1.227 (31.17) 0.191 (4.85) 0.239 (6.07) 116 (1.59) 116 (1.59) 116 (1.59)112 1.912 (48.56) 0.006

46、(0.15) 0.024 (0.61) 1.894 (48.11) 0.006 (0.15) 0.024 (0.61) 1.375 (34.93) 1.446 (36.73) 0.200 (5.08) 0.250 (6.35) 116 (1.59) 116 (1.59) 116 (1.59)2 2.387 (60.63) 0.006 (0.15) 0.024 (0.61) 2.369 (60.17) 0.006 (0.15) 0.024 (0.61) 1.500 (38.10) 1.881 (47.78) 0.218 (5.54) 0.275 (6.99) 116 (1.59) 116 (1.

47、59) 116 (1.59)212 2.889 (73.38) 0.007 (0.18) 0.030 (0.76) 2.868 (72.85) 0.007 (0.18) 0.030 (0.76) 1.750 (44.45) 2.250 (57.15) 0.276 (7.01) 0.345 (8.76) 332 (2.38) 18 (3.18) 18 (3.18)3 3.516 (89.31) 0.008 (0.20) 0.030 (0.76) 3.492 (88.70) 0.008 (0.20) 0.030 (0.76) 1.875 (47.63) 2.820 (71.63) 0.300 (7

48、.62) 0.375 (9.53) 332 (2.38) 18 (3.18) 18 (3.18)312 4.016 (102.01) 0.008 (0.20) 0.030 (0.76) 3.992 (101.4) 0.008 (0.20) 0.030 (0.76) 2.125 (53.98) 3.280 (83.31) 0.318 (8.08) 0.400 (10.16) 332 (2.38) 18 (3.18) 18 (3.18)4 4.518 (114.76) 0.009 (0.23) 0.030 (0.76) 4.491 (114.1) 0.009 (0.23) 0.030 (0.76)

49、 2.250 (57.15) 3.737 (94.92) 0.337 (8.56) 0.420 (10.67) 332 (2.38) 18 (3.18) 18 (3.18)5 5.583 (141.81) 0.010 (0.25) 0.060 (1.52) 5.553 (141.0) 0.010 (0.25) 0.060 (1.52) 2.625 (66.68) 4.703 (119.46) 0.375 (9.53) 0.470 (11.94) 332 (2.38) 18 (3.18) 18 (3.18)6 6.647 (168.83) 0.011 (0.28) 0.060 (1.52) 6.614 (168.0) 0.011 (0.28) 0.060 (1.52) 3.000 (76.20) 5.646 (143.41) 0.432 (10.97) 0.54