ASTM D2559-2012a(2018) Standard Specification for Adhesives for Bonded Structural Wood Products for Use Under Exterior Exposure Conditions.pdf

1、Designation: D2559 12a (Reapproved 2018)Standard Specification forAdhesives for Bonded Structural Wood Products for UseUnder Exterior Exposure Conditions1This standard is issued under the fixed designation D2559; the number immediately following the designation indicates the year oforiginal adoption

2、 or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.IN

3、TRODUCTIONThis specification, which was initially approved in 1966, was developed to ensure that adhesivesdeveloped and used in structural glued laminated timber (glulam) are considered suitable for theintended application. This would include, as a maximum level of severity in the case of moistureef

4、fects, full and continuous exposure to the weather.The use of adhesives for structural wood products has expanded beyond Glulam to include productssuch as Structural Composite Lumber, wood I-Joists and various composites adhesively bonded usinga variety of materials. Although most structural glued w

5、ood products have traditionally specified anadhesive suitable for exterior exposure, the actual exposure of glued wood products to exteriorconditions may range from exposure to the weather for brief periods of time, to continuous exposureto a marine environment.A distinction between adhesive certifi

6、cation and product performance requirements is necessary toensure the broadest possible acceptance of adhesive systems.1. Scope1.1 This specification covers adhesives suitable for thebonding of wood, including treated wood, into structural woodproducts for general construction or other uses where ah

7、igh-strength, durable adhesive bond is required.1.2 This specification includes test methods that may bereferenced by specific product standards for the evaluation andapproval of structural wood adhesives. Methods are included toevaluate adhesives intended for use in exterior exposure.NOTE 1Consult

8、the Commentary in Appendix X1 regarding the intentand limitations of each test method contained in this specification.1.3 Description of Bondline PerformanceIt is recognizedthat structural wood adhesives are used in various applicationsand levels of severity in terms of moisture content, loading,cyc

9、lic and seasonal weather conditions, heat exposure andother use conditions. It is the intent of this standard todetermine the suitability of an adhesive for use under variouslevels of severity and conditions with specific and appropriatetest methods and requirements.NOTE 2This specification does not

10、 contain specific tests outlined fordifferent chemical types of adhesives.1.4 Strength and durability requirements of the adhesive arebased on the performance of the adhesive in laminated wood asmeasured by:1.4.1 Resistance to shear by compression loading afterconditioning to the target moisture con

11、tent indicated in 14.2.3and meeting requirements in 14.4.1.4.2 Resistance to delamination during exposure to threecycles of vacuum pressure wetting followed by drying atelevated temperature as indicated in 15.3 and meeting require-ments in 15.4.1.4.3 Resistance to creep under static load by subjecti

12、ng testspecimens to a specified shear stress and exposing one set oftest specimens to an environment of elevated temperature andambient humidity and another set to an environment of highhumidity and meeting requirements set forth in 16.3.1.4.4 For applications involving chemical treatment, theadhesi

13、ve shall be evaluated using representative samples oftreated wood.NOTE 3When using chemically treated wood, compatibility betweenthe treatment, adhesive, and wood is to be considered and agreed uponbetween the chemical manufacture and the user.NOTE 4Additional durability testing may also be required

14、 as specifiedby individual product standards. Consult the Commentary in Appendix X1for additional information and guidance as to the type of durability testingthat may be appropriate to supplement this specification when character-izing the adhesive for suitability with specific wood products.1This

15、specification is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.30 on WoodAdhesives.Current edition approved Aug. 1, 2018. Published August 2018. Originallyapproved in 1966. Last previous edition approved in 2012 as D2559 12a1. DOI:10.15

16、20/D2559-12AR18.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDeve

17、lopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.11.5 The evaluation of adhesives for use in ground contactand marine exposures are beyond the scope of this specifica-tion.1.6 The evaluation of binder ad

18、hesives is beyond the scopeof this specification.1.7 The values stated in SI units are to be regarded as thestandard. The values in parentheses are for information only.1.8 The text of this specification references notes, footnotesand a commentary which provide explanatory material. Thesenotes, foot

19、notes and commentary (excluding those in tablesand figures) shall not be considered as requirements of thespecification.1.9 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-pr

20、iate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.10 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevel

21、opment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D9 Terminology Relating to Wood and Wood-Based Prod-uctsD143 Test Methods for Small Clear Specimens of TimberD90

22、5 Test Method for Strength Properties of AdhesiveBonds in Shear by Compression LoadingD907 Terminology of AdhesivesD1165 Nomenclature of Commercial Hardwoods and Soft-woodsD1583 Test Method for Hydrogen Ion Concentration of DryAdhesive FilmsD2555 Practice for Establishing Clear Wood Strength ValuesD

23、3535 Test Method for Resistance to Creep Under StaticLoading for Structural Wood Laminating Adhesives UsedUnder Exterior Exposure ConditionsD4442 Test Methods for Direct Moisture Content Measure-ment of Wood and Wood-Based MaterialsD4300 Test Methods for Ability of Adhesive Films toSupport or Resist

24、 the Growth of FungiD5055 Specification for Establishing and Monitoring Struc-tural Capacities of Prefabricated Wood I-JoistsD5266 Practice for Estimating the Percentage of WoodFailure in Adhesive Bonded JointsD5456 Specification for Evaluation of Structural CompositeLumber ProductsE6 Terminology Re

25、lating to Methods of Mechanical TestingE41 Terminology Relating to ConditioningE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3. Terminology3.1 DefinitionsMany terms in this specification are de-fined in Terminologies D9 and D907.3.2 Definitions of Te

26、rms Specific to This Standard:3.2.1 delamination, nthe separation of layers in a laminatebecause of failure of the adhesive, either in the adhesive itselfor at the interface between the adhesive and the adherend.3.2.2 engineered wood product, na product consisting of acombination of smaller wood-bas

27、ed components bonded to-gether using a structural adhesive and designed using engineer-ing methods; an alternative to traditional sawn lumber.3NOTE 5The following ASTM standards may be referred to for otherterms used in this specification: Nomenclature D1165, and TerminologiesD9, E6, and E41.3.2.3 e

28、xterior exposure, nservice environment that causephysical and chemical changes similar to that observed fromweathering in which a wood product, including any adhesivebondlines, is subjected to weathering, including but not limitedto: rain, snow, heat, cold and ultraviolet radiation and theircyclic o

29、r seasonal effects.3.2.4 glulam, nsynonym for structural-glued-laminatedtimber.3.2.5 structural-glued-laminated timber, nan engineeredstress-rated product of a timber laminating plant comprisingassemblies of specially selected and prepared wood lamina-tions securely bonded together with adhesives, w

30、ith the fol-lowing characteristics: (1) the grain of all laminations isapproximately parallel longitudinally; and (2) the laminationsmay be comprised of pieces end-joined to form any length, ofpieces placed or glued edge-to-edge to make wider ones or ofpieces bent to curved form during gluing. (Syno

31、nym: glulam)ANSI/AITC A190.1. American National Standard for WoodProductsStructural Glued Laminated Timber (edited to con-form with ASTM format).3.2.6 weathering, na complex series of physical andchemical changes occurring in wood products, including butnot limited to, checking, dimension stability

32、and chemicaldecomposition as well as a change in adhesive bondlineintegrity related to the natural swelling and shrinking stresseswhen exposing to the natural elements such as air, water, lightand man-made pollutants.4. Significance and Use4.1 Structural design based on strength of material prin-cip

33、les of the structural components, including the adhesive andthe adhesives potential durability, requires that the suitabilityfor structural exterior exposure be predicted.4.2 Performance of the adhesive for resistance to shear bycompression loading, resistance to delamination during accel-erated agi

34、ng, exposure to wetting and drying, and resistance to2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3America

35、n Forest and Paper Association, American Wood Council, EngineeredWood Products At a Glance, http:/www.woodaware.info/guideewp.html.D2559 12a (2018)2creep under load data developed by this test aid in determiningif the adhesive is suitable for use in structural wood productsunder conditions of exteri

36、or exposure.4.3 Test methods specified in the scope of this specificationare intended to provide the minimum basis for determining thesuitability of an adhesive for use in exterior exposure condi-tions.NOTE 6Product-specific standards should be consulted for test meth-ods applicable to desired servi

37、ce conditions, and appropriate criteria incontext with anticipated in-service product performance requirements.4.4 Test methods indicated for approval and certification ofadhesives can be useful to adhesive manufacturers, testinglaboratories, quality control agencies, architects, specifiers,other pr

38、ofessionals and the general public.4.5 The suitability of adhesive systems for use in themanufacture of engineered wood products for exterior appli-cations is dependent on both the adhesive certification testrequirements specified in this specification, and performancerequirements provided in specif

39、ic product standards.4.6 This specification does not purport to address all testcriteria required to fully identify the suitability of the adhesivein a structural wood product.5. Classification5.1 The manufacturer shall classify the adhesive as togeneral type. Typical classifications include, but ar

40、e not limitedto: resorcinol, phenol-resorcinol, phenol, melamine, structuralpolyurethane, emulsion polymer isocyanate, etc.5.2 The manufacturer may be considered to be the testingfacility certifying the adhesive.6. Ordering Information6.1 The manufacturer will furnish the adhesive in anysuitable for

41、m agreeable to the purchaser.7. Fillers and Extenders7.1 If amylaceous or protein fillers and extenders are used,the adhesive must not only pass requirements of thisspecification, but in addition, possess sufficient antifungalproperties to inhibit the growth of selected fungal species whentested in

42、accordance with Test Methods D4300. The adhesivemanufacturer shall state in his bulletin whether such materialsare present.8. Chemical Requirements8.1 The cured adhesive film shall develop a pH value of notless than 2.5 when tested in accordance with Test MethodD1583.9. Physical Requirements9.1 The

43、adhesive manufacturer shall furnish written instruc-tions stating the general chemical type of adhesive, its storageand mixing procedure, the method of wood preparation, andany other data which is pertinent to the use of the adhesive inthe manufacture of laminated wood products.9.2 The adhesive must

44、 pass the tests required by thisspecification for all limiting conditions recommended in themanufacturers bulletin. The information furnished by themanufacturer should include each of the following for eachspecies of wood included in his recommendations:9.2.1 Limits of working life,9.2.2 Minimum and

45、 maximum open and closed assemblytimes as dictated by temperature, moisture content of the wood,mix age, etc.,9.2.3 Minimum spread rates for assembly times and useconditions as indicated in 9.2.2,9.2.4 Minimum cure time and temperature of bondline forcomplete cure,9.2.5 Minimum pressure, and9.2.6 Ma

46、ximum and minimum allowable moisture contentof the wood.10. Selection and Preparation of Wood for Testing ofAdhesives10.1 Test the adhesive on the species of wood to be bondedor for which it is recommended including chemically treatedwood (see Note 7). The wood shall have a maximum slope ofgrain of

47、1 in 15 on any face or any edge. The wood shallcontain no knots larger than 3 mm (18 in.) in diameter and shallbe free from decay, machining defects (such as chipped grain,dubbed ends, feed roll polish, coarse knife marks, and feed rollcompression), and any drying defects such as case hardening,coll

48、apse, splits, or checks. Use only flat-grained wood.NOTE 7Grouping of species is not permitted.10.2 Wood Moisture Content:10.2.1 Ambient Curing AdhesivesCondition the wood at23 6 2C (73.4 6 3.6F) and a relative humidity of 50 to 70 %(preferably 65 %) until a moisture content of 8 to 14 % or,preferab

49、ly 9 to 12 %, has been attained.10.2.2 Hot Press Curing AdhesivesCondition the wood at23 6 2C (73.4 6 3.6F) and a relative humidity of less than50 % until a moisture content of 3 to 8 % has been attained.10.3 Freshly surface each lamination before bonding withthe adhesive to be tested. Remove at least 0.4 mm (164 in.)from each face within 24 h of bonding. The machiningtolerances for each lamination used in preparing the testsamples shall be no greater than 60.25 mm (0.01 in.) betweenlaminations and 60.20 mm (0.008 in.) within laminations.11. Preparation