ASTM D2698-2005 Standard Test Method for Determination of the Pigment Content of Solvent-Reducible Paints by High-Speed Centrifuging《高速离心法测定可还原溶剂型涂料中颜料含量的标准试验方法》.pdf

1、Designation: D 2698 05Standard Test Method forDetermination of the Pigment Content of Solvent-ReduciblePaints by High-Speed Centrifuging1This standard is issued under the fixed designation D 2698; the number immediately following the designation indicates the year oforiginal adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This test

3、method covers the separation of pigment fromsolvent-reducible paints and the calculation of the percentpigment from the results of nonvolatile determinations on thetotal paint and the separated vehicle.NOTE 1This test method has been proven to be applicable to mostsolvent-reducible paints, the excep

4、tion being those paints containingseverely bleeding pigments or pigments such as carbon black that are verydifficult or impossible to centrifuge.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not pur

5、port to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D

6、2369 Test Method for Volatile Content of Coatings3. Significance and Use3.1 This test method describes a rapid method for separatingpigment from solvent-reducible paints.3.2 This test method is used by paint producers and con-sumers for product acceptance and process control.4. Apparatus4.1 Laborato

7、ry Centrifuge, capable of developing 32 000 gor higher.35. Procedure5.1 Shake the sample for 10 min on a mechanical shaker,stir with a paddle to loosen any caked pigment, and shake againfor 10 min. If necessary, repeat until there are no lumps presentand the sample is thoroughly mixed.5.2 Add the mi

8、xed paint to the centrifuge container untilsufficient paint is added to permit the recovery of 25 mLminimum of clear vehicle. Revolve the bowl at 32 000 g orhigher for 15 min or until a clear vehicle is obtained.5.3 Transfer the vehicle carefully, so as not to dislodge anyof the pigment from the wal

9、ls, into a jar that is immediatelycapped to prevent any solvent losses by evaporation. Use thisvehicle for the determination of the nonvolatile content of theseparated vehicle.6. Percent Paint and Vehicle Solids6.1 Determine the percent nonvolatile content of the origi-nal paint and the separated ve

10、hicle in accordance with TestMethod D 2369.7. Calculation7.1 Calculate the weight percent pigment of paint, P,asfollows:P 5 A 2 B! 3 100/100 2 B (1)where:A = nonvolatile content of paint, %, andB = nonvolatile content of separated vehicle, %.1This test method is under the jurisdiction of ASTM Commit

11、tee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.Current edition approved Jan. 1, 2005. Published February 2005. Originallyapproved in 1965. Last previous edition approved in 19

12、99 as D 2698 90 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3A supercentrifuge or a centrifuge equ

13、ipped with a high-speed head have beenfound satisfactory for this purpose. Any centrifuge capable of developing 32 000 gand having facilities for sealing the specimen to prevent solvent loss should alsoprove to be satisfactory.To calculate the gravities developed by a particular centrifuge use the f

14、ollowingcalculation:g=rotating radius, cm 3 r/min23 1.118 3 1051Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.8. Recovery of Pigment for Analysis8.1 The pigment may be completely recovered from thecentrifuge bowl and washed to remov

15、e residual vehicle. Thismay be done either by a Soxhlet extraction or washing thepigment with a suitable solvent and recentrifuging.NOTE 2It has been noted that the removal of the pigment from thebowl of a Sharples supercentrifuge can be facilitated by lining the bowlwith a piece of polyester film p

16、rior to adding the sample and subsequentlyjust slipping the polyester film along with the pigment out of the bowl.9. Precision and Bias9.1 PrecisionThe precision estimates are based on aninterlaboratory study of this test method in which air dryingmaterials were analyzed in duplicate or triplicate.

17、The follow-ing criteria should be used for judging the acceptability ofresults at the 95 % confidence level:9.1.1 RepeatabilityThe difference between two results,each the mean of duplicate determinations obtained by thesame operator, will approximate 0.1 % absolute. Two suchvalues should be consider

18、ed suspect if they differ by more than0.25 % absolute.9.1.2 ReproducibilityThe difference between two results,each the mean of duplicate determinations obtained by opera-tors in different laboratories, will approximate 0.25 % absolute.Two such values should be considered suspect if they differ bymor

19、e than 0.5 % absolute.9.1.3 This precision pertains to air-drying materials. Heat-reactive vehicles will have a repeatability and reproducibilityapproximately twice as large, that is, 0.5 % and 1.0 % absolute.9.1.4 It should be noted that when the solvent content of thetotal paint is very low (15 %

20、or less) the precision of this testmethod will not be satisfactory unless the nonvolatile determi-nation is precise to the second decimal place.9.2 BiasBias cannot be determined for this method be-cause there are no accepted standards for pigment content ofsolvent-reducible paints.10. Keywords10.1 h

21、igh speed centrifuging; pigment content; solvent-reducible paintASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any suc

22、h patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invite

23、d either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a

24、fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D2698052