ASTM D2822-2005 Standard Specification for Asphalt Roof Cement Asbestos Containing《沥青屋面胶粘剂的标准规范》.pdf

1、Designation: D 2822 05Standard Specification forAsphalt Roof Cement, Asbestos-Containing1This standard is issued under the fixed designation D 2822; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers asbestos-containing asphaltroof

3、cement used for trowel application to roofings andflashings.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 The following safety hazards caveat pertains only to thetest methods described in this specification: This stan

4、dard doesnot purport to address all of the safety concerns, if any,associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM S

5、tandards:2D 312 Specification for Asphalt Used in RoofingD 449 Specification for Asphalt Used in Dampproofing andWaterproofingD 946 Specification for Penetration-Graded Asphalt Ce-ment for Use in Pavement ConstructionD 1079 Terminology Relating to Roofing, Waterproofingand Bituminous MaterialsD 6511

6、 Test Methods for Solvent Bearing BituminousCompounds3. Terminology3.1 For definitions of terms used in this specification, seeTerminology D 1079.4. Classification4.1 Type I is made from asphalts characterized as self-healing, adhesive, and ductile, and conforming to the require-ments of Specificati

7、on D 312, Type I; Specification D 449,Types I or II; or Specification D 946.4.1.1 Class I is used for application to essentially drysurfaces.4.1.2 Class II is used for application to damp, wet, orunderwater surfaces.4.2 Type II is made from asphalt characterized by highsoftening point and relatively

8、 low ductility, and conforming tothe requirements of Specification D 312, Types II or III; orSpecification D 449, Type III.4.2.1 Class I is used for application to essentially drysurfaces.4.2.2 Class II is used for application to damp, wet, orunderwater surfaces.5. Materials and Manufacture5.1 Aspha

9、lt roof cement shall consist of an asphalt base,volatile petroleum solvents, and mineral stabilizers includingasbestos fiber, mixed to a smooth, uniform consistency suitablefor trowel application.6. Composition6.1 Asphalt roof cement complying with this specificationshall conform to the following co

10、mposition limits:min maxWater, % . 1.0 (D 6511,Section 10)Nonvolatile matter, % 70 . (D 6511,Section 7)Asbestos and othermineral stabilizers, %15 45 (D 6511,Section 18)Asphalt, % 30 60 (D 6511,Section 18)Mineral matter basedon original mass ofinsoluble residue, %80 . (D 6511,Section 19)1This specifi

11、cation is under the jurisdiction of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.05on Solvent-Bearing Bituminous Compounds for Roofing and Waterproofing.Current edition approved Oct. 1, 2005. Published October 2005. Originallyapproved in 1969. L

12、ast previous edition approved in 1997 as D 2822 91 (1997)e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1

13、Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Physical Requirements7.1 UniformityA thoroughly stirred sample shall show noseparation of solvent or settling that cannot be overcome bymoderate stirring after standing for 72 h at ro

14、om temperature ina closed container. (See Test Methods D 6511, Section 5 onUniformity.)7.2 WorkabilityThe cement shall be of a consistency thatwill spread readily and permit troweling smooth coatings, 2 to6mm(116 to14 in.) thick, on prepared roofing, saturated felt,and metal surfaces at ambient temp

15、eratures above 10C (50F).7.3 Behavior at 60C (140F)The cement shall show noevidence of blistering, and sag or slide shall be no greater than6mm(14 in.). (See Test Methods D 6511, Section 12 onBehavior at 60C (140F).)7.4 Pliability at 0C (32F)There shall be no cracking orseparation of the cement from

16、 the metal. (See Test MethodsD 6511, Section 13 on Pliability at 0C (32F).)7.5 Adhesion to Damp, Wet, or Underwater SurfacesTheaverage of three test samples shall be greater than 80 %adhesion for compliance with Class II requirements. (See TestMethods D 6511, Section 17 on Adhesion to Damp, Wet, orU

17、nderwater Surfaces.)8. Sampling8.1 Sample the material from the original containers imme-diately after stirring to a uniform consistency in accordancewith Section 4, Sampling, of Test Methods D 6511. Restirsamples to ensure uniformity immediately before withdrawingportions for individual tests.9. Te

18、st Methods9.1 Determine composition and physical requirements byusing the procedures in Test Methods D 6511.10. Precision10.1 See Section 21, Precision and Bias, of Test MethodsD 6511.11. Inspection11.1 Inspection of the material shall be agreed upon by thepurchaser and the seller as part of the pur

19、chase contract.12. Rejection and Resubmittal12.1 Failure to conform to any of the requirements pre-scribed in this specification shall constitute grounds for rejec-tion. In cases of rejection, the seller shall have the right toreinspect and resubmit the lot after removal of those packagesnot conform

20、ing to the specified requirements.13. Packaging and Package Marking13.1 Asphalt roofing cement shall be suitably packaged topermit acceptance by the carrier and to afford adequateprotection from the normal hazards of handling and shipment.13.2 Each container shall be plainly parked with the nameand

21、brand of the manufacturer or supplier, the type of product,the manufacturers production code or lot number, and wordingindicating that the material contains asbestos.13.3 Each container shall be plainly parked to indicate thatthe product was manufactured to meet ASTM D 2822.14. Keywords14.1 asbestos

22、; asphalt; roof cementASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringeme

23、nt of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or

24、for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views kno

25、wn to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D2822052