ASTM D2880-2014 Standard Specification for Gas Turbine Fuel Oils《燃气轮机用燃料油的标准规格》.pdf

1、Designation: D2880 13bD2880 14Standard Specification forGas Turbine Fuel Oils1This standard is issued under the fixed designation D2880; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenth

2、eses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers the selection of fuels for gas turbines

3、, excepting gas turbines used in aircraft, for the guidance ofinterested parties such as turbine manufacturers and the suppliers and purchasers of fuel oils. The specification sets forth theproperties of fuels at the time and place of custody transfer to the user.1.2 Three appendixes are provided fo

4、r informational purposes only and do not constitute a requirement of this specificationunless mutually agreed upon between the interested parties.1.2.1 Appendix X1 describes the five grades of gas turbine fuels covered by this specification. Further, it states the significanceof various test methods

5、 used in inspecting the fuels.1.2.2 Appendix X2 discusses the sources of fuel contaminants and notes the significance of such contaminants in the operationof gas turbines and gas turbine fuel systems. The particular significance of trace metals in gas turbine fuels is noted. Upper limitsof trace met

6、als are recommended for the various grades of gas turbine fuels, but these recommended limits do not constitute arequirement of the specification unless mutually agreed upon by the interested parties. Limitations due to the use of used orrecycled oil are also noted.NOTE 1The gas turbine operator sho

7、uld consult Practice D4418 for methods of ensuring fuels of adequate cleanliness and for guidance on long-termstorage of distillate fuels and on liquids from non-petroleum sources as gas turbine.NOTE 2Nothing in this specification shall preclude observance of federal, state, or local regulations whi

8、ch may be more restrictive.NOTE 3The generation and dissipation of static electricity can create problems in the handling of distillate gas turbine fuel oils. For more informationon the subject, see Guide D4865.2. Referenced Documents2.1 ASTM Standards:2D56 Test Method for Flash Point by Tag Closed

9、Cup TesterD86 Test Method for Distillation of Petroleum Products at Atmospheric PressureD93 Test Methods for Flash Point by Pensky-Martens Closed Cup TesterD97 Test Method for Pour Point of Petroleum ProductsD129 Test Method for Sulfur in Petroleum Products (General High Pressure Decomposition Devic

10、e Method)D396 Specification for Fuel OilsD445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)D482 Test Method for Ash from Petroleum ProductsD524 Test Method for Ramsbottom Carbon Residue of Petroleum ProductsD975 Specification for Diesel

11、Fuel OilsD1266 Test Method for Sulfur in Petroleum Products (Lamp Method)D1298 Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products byHydrometer MethodD1552 Test Method for Sulfur in Petroleum Products (High-Temperature Method)D1796 Test Method f

12、or Water and Sediment in Fuel Oils by the Centrifuge Method (Laboratory Procedure)D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry1 This specification is under the jurisdiction ofASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lu

13、bricants and is the direct responsibility of SubcommitteeD02.E0 on Burner, Diesel, Non-Aviation Gas Turbine, and Marine Fuels.Current edition approved Nov. 15, 2013Aug. 1, 2014. Published November 2013August 2014. Originally approved in 1970. Last previous edition approved in 2013 asD2880 13a.D2880

14、13b. DOI: 10.1520/D2880-13B.10.1520/D2880-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is

15、 not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropr

16、iate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States

17、1D2709 Test Method for Water and Sediment in Middle Distillate Fuels by CentrifugeD3605 Test Method for Trace Metals in Gas Turbine Fuels by Atomic Absorption and Flame Emission SpectroscopyD3828 Test Methods for Flash Point by Small Scale Closed Cup TesterD4052 Test Method for Density, Relative Den

18、sity, and API Gravity of Liquids by Digital Density MeterD4294 Test Method for Sulfur in Petroleum and Petroleum Products by Energy Dispersive X-ray Fluorescence SpectrometryD4418 Practice for Receipt, Storage, and Handling of Fuels for Gas TurbinesD4865 Guide for Generation and Dissipation of Stati

19、c Electricity in Petroleum Fuel SystemsD5453 Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel,and Engine Oil by Ultraviolet FluorescenceD5949 Test Method for Pour Point of Petroleum Products (Automatic Pressure Pulsing Method)D5950 T

20、est Method for Pour Point of Petroleum Products (Automatic Tilt Method)D5985 Test Method for Pour Point of Petroleum Products (Rotational Method)D6469 Guide for Microbial Contamination in Fuels and Fuel SystemsD6728 Test Method for Determination of Contaminants in Gas Turbine and Diesel Engine Fuel

21、by Rotating Disc ElectrodeAtomic Emission SpectrometryD7042 Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of KinematicViscosity)D7094 Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) TesterD7220 Test Method for Sulfur in

22、Automotive, Heating, and Jet Fuels by Monochromatic Energy Dispersive X-ray FluorescenceSpectrometry2.2 Other Documents:326 CFR Part 48 Diesel Fuel Excise Tax; Dye Color and Concentration40 CFR Part 80 Regulation of Fuels and Fuel Additives3. Terminology3.1 Definitions:3.1.1 hydrocarbon oil, na homo

23、geneous mixture with elemental composition primarily of carbon and hydrogen that may alsocontain sulfur, oxygen, or nitrogen from residual impurities and contaminants associated with the fuels raw materials andmanufacturing processes and excluding added oxygenated materials.3.1.1.1 DiscussionNeither

24、 macro nor micro emulsions are included in this definition since neither are homogeneous mixtures.3.1.1.2 DiscussionExamples of excluded oxygenated materials are alcohols, esters, ethers, and triglycerides.3.2 Definitions of Terms Specific to This Standard:3.2.1 fuel contaminantsfuel components othe

25、r than hydrocarbon oils. In the present context the contaminants are foreignmaterials that make the fuel less suitable or even unsuitable for the intended use.3.2.1.1 DiscussionThe contaminants of primary interest are foreign materials introduced subsequent to the manufacture of specification qualit

26、y fuel.Hence they are materials introduced in the distribution system (that is, storage tanks, pipelines, tank trucks, barges, etc.) or in theusers storage and handling system, or generated within these systems (rust generated in steel pipes and tanks by moist fuel, andso forth). Contaminants may be

27、 soluble or insoluble in the fuel.3.2.2 fuel entering the combustor(s)the fuel that is actually burned in the gas turbine. Fuel may be sampled at a point upstreamfrom the point of entry into the combustor(s), provided the sample is representative of the fuel actually entering the combustor(s).3.1.3

28、hydrocarbon oil, na mixture with elemental composition primarily of carbon and hydrogen, also containing sulfur,oxygen or nitrogen from residual impurities and contaminants associated with the fuels raw materials and manufacturingprocesses, and excluding added oxygenated materials.3.1.3.1 Discussion

29、3 Available from Superintendent of Documents, U. S. Government Printing Office, Washington, DC 20402.D2880 142Examples of excluded oxygenated materials include but are not limited to alcohols, esters, ethers and triglycerides.NOTE 4Additives are generally included in finished gas turbine fuel oil to

30、 improve performance properties (corrosion and so forth).4. General Requirements4.1 The grades of gas turbine fuels herein specified shall be homogeneous mixtures of hydrocarbon oils with the use of additivesto enhance performance properties, if required. The hydrocarbon oils shall be free of inorga

31、nic acid, and free of excessive amountsof solid or fibrous foreign matter likely to make frequent cleaning of suitable strainers necessary.NOTE 4Additives are generally included in finished gas turbine fuel oil to improve performance properties (corrosion and anti-corrosion, and soforth).4.2 All gra

32、des containing residual components shall remain homogeneous in normal storage and not separated by gravity intolight and heavy oil components outside the viscosity limits for the grade.5. Detailed Requirements5.1 The various grades of gas turbine fuel oil shall conform to the limiting requirements s

33、hown in Table 1. As noted in thesupplementary footnotes to Table 1, the requirements for Grade Nos. 1-GT and 2-GT conform in most respects to correspondingGrade Nos. 1 and 2 fuels in Specification D396, and to Grade Nos. 1-D and 2-D in Specification D975. The viscosity range ofGrade Nos. 3-GT and 4-

34、GT fuel brackets the Grade Nos. 4, 5, and 6 of Specification D396 and Grade No. 4-D of SpecificationD975. It is the intent that fuels meeting Specification D396 and D975 requirements may also be supplied under these specificationsprovided they meet the requirements listed in Table 1.TABLE 1 Detailed

35、 Requirements for Gas Turbine Fuel Oils at Time and Place of Custody Transfer to UserA,B,CPropertyASTMTestMethodDGradeENo. 0-GT No. 1-GTF No. 2-GTF No. 3-GT No. 4-GTFlash pointC (F) minD93 G 38 (100) 38 (100) 55 (130) 66 (150)Water and sediment% vol maxD2709D17960.05.0.05.0.05.1.0.1.0DistillationTem

36、perature D86C (F)90 % volume recoveredmin . . 282 . .max . 288 338 . .Kinematic viscosity2 mm/sH D445AT 40C (104F) min G 1.3 1.9 5.5 5.5max 2.4 4.1 . .AT 100C (212F) max . . 50.0 50.0RamsbottomCarbon residueon10 % distillationResidue% mass, maxD524 0.15 0.15 0.35 . .Ash% mass, max D482 0.01 0.01 0.0

37、1 0.03 .Density at D129815C kg/m3max . 850 876 . .Pour pointHC (F) maxD97 . 18 6 . .A To meet special operating conditions, modifications of individual limiting requirements may be agreed upon between purchaser, seller, and manufacturer.B Gas turbines with waste heat recovery equipment may require f

38、uel sulfur limits to prevent cold end corrosion. Environmental limits may also apply to fuel sulfur in selectedareas in the United States and in other countries.C See Section 4 and 5 for further statements on gas turbine fuel oil requirements.D The test methods indicated are the approved referee met

39、hods. Other acceptable methods are indicated in 6.1.E No. 0-GT includes naphtha, Jet B fuel and other volatile hydrocarbon liquids. No. 1-GT corresponds in general to specification D396 Grade No. 1 fuel and D975 Grade1-D diesel fuel in physical properties. No. 2-GT corresponds in general to Specific

40、ation D396 No. 2 fuel and D975 Grade 2-D diesel fuel in physical properties. No. 3-GTand No. 4-GT viscosity range brackets specification D396 Grades No. 4, No. 5 (light), No. 5 (heavy), and No. 6, and D975 Grade No. 4-D diesel fuel in physical properties.F Under United States regulations, Grades No.

41、 1-GT and No. 2-GT are required by 40 CFR Part 80 to contain a sufficient amount of dye Solvent Red 164 so its presenceis visually apparent.At or beyond terminal storage tanks, they are required by 26 CFR Part 48 to contain the dye Solvent Red 164 at a concentration spectrally equivalentto 3.9 lb pe

42、r thousand barrels of the solid dye standard Solvent Red 26.G When the flash point is below 38C (100F) or when kinematic viscosity is below 1.3 mm2/s at 40C (104F) or when both conditions exist, the turbine manufacturershould be consulted with respect to safe handling and fuel system design.H For co

43、ld weather operation, the pour point should be specified 6C below the ambient temperature at which the turbine is to be operated except where fuel heatingfacilities are provided. When a pour point less than 18C is specified for Grade No. 2-GT, the minimum viscosity shall be 1.7 mm2/s and the minimum

44、 90 % recoveredtemperature shall be waived.D2880 1435.2 Modifications of limiting requirements and the inclusion of fuel additives to meet special operating conditions may beagreed upon between the interested parties.5.3 The properties listed in this specification are those of greatest significance

45、in obtaining acceptable performance of theturbine. However, trace metals, even in fractional parts per million, are detrimental to gas turbine service life. Information on themaximum concentration of critical metallic elements in the fuel as it enters the turbine combustor(s) is provided in Appendix

46、 X2.Distillate fuels are usually of satisfactory purity as refined, but suppliers rarely have control over possible contamination by tracemetals in distribution and storage. The limits in Appendix X2, although required as the fuel enters the combustor(s), do not applyto the fuel as delivered unless

47、mutually agreed upon by the interested parties. Fuels may, therefore, require on-site clean-up, qualitycontrol procedures, special handling, or other arrangements.6. Test Methods6.1 The requirements enumerated in this specification shall be determined in accordance with the following ASTM methodsexc

48、ept as noted:6.1.1 Flash PointTest Methods D93, except where other methods are prescribed by law. For all grades, Test Method D3828and D7094 may be used as an alternative with the same limits. For Grades No. 1-GT and No. 2-GT, Test Method D564 may beused as an alternative with the same limits provid

49、ed the flash point is below 93C and the viscosity is below 5.5 mm2/s at 40C.This test method will give slightly lower values. In case of dispute, Test Method D93 shall be used as the referee method.6.1.2 Pour PointTest Method D97. For all grades, the automatic Test Methods D5949, D5950, or D5985 can be used asalternates with the same limits. In case of dispute, Test Method D97 shall be used as the referee method.6.1.3 Water and SedimentTest Method D2709 is used for Grades 0-GT, 1-GT, and 2-GT. Test Method D1796 is used forGrades 3-GT a