ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:64.66KB ,
资源ID:513824      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-513824.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D2942-2002(2018) Standard Test Method for Total Acid Acceptance of Halogenated Organic Solvents (Nonreflux Methods).pdf)为本站会员(wealthynice100)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D2942-2002(2018) Standard Test Method for Total Acid Acceptance of Halogenated Organic Solvents (Nonreflux Methods).pdf

1、Designation: D2942 02 (Reapproved 2018)Standard Test Method forTotal Acid Acceptance of Halogenated Organic Solvents(Nonreflux Methods)1This standard is issued under the fixed designation D2942; the number immediately following the designation indicates the year oforiginal adoption or, in the case o

2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This tes

3、t method covers the determination of the totalacid acceptance including amine and neutral type (alphaepoxide) stabilizers in halogenated organic solvents.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does

4、 not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Specific precautionar

5、y statements are given in Section 7.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Tra

6、de Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD2106 Test Methods for Determination of Amine AcidAcceptance (Alkalinity) of Halogenated Organic SolventsE200 Practice for Preparation, Standardization, and Stor

7、ageof Standard and Reagent Solutions for Chemical Analysis3. Summary of Test Method3.1 Test Method AThe total acid acceptance is determinedby the reaction of the sample with a known amount ofhydrochloric acid that has been dissolved in isopropyl alcohol.The excess acid remaining after the reaction w

8、ith the acidacceptor is then back-titrated with a standardized solution ofsodium hydroxide. The total acid acceptance of the stabilizerscan be calculated and reported as weight % NaOH.3.2 Test Method BThe acid acceptor content is determinedby gas chromatography or another validated method such asden

9、sity or refractive index and the acid acceptance is calculatedfrom the weight % acid acceptor. Techniques like density andrefractive index are generally suitable only for two-part sys-tems. The method for the determination of the acid acceptorshould be validated for the sample being analyzed to ensu

10、rethere is no interference, particularly from such things as oilsand reaction products when measuring acid acceptance ofproduct that is in use such as vapor degreasers.4. Significance and Use4.1 Solvents that have been depleted in stabilizer contentcan become acidic. Acids can cause corrosion to pro

11、cess andstorage equipment used for halogenated solvents.4.2 Halogenated organic solvents may contain amine type(alkaline, aqueous extractable) acid accepting additives, neutraltype (typically epoxide) acid accepting additives or both. Thistest method can determine the combined acid acceptance frombo

12、th types of stabilizers. In addition, if the amine acidacceptance is determined by a separate procedure (see TestMethods D2106), the amount of neutral acid accepting stabi-lizers in a solvent can be calculated from the differencebetween combined and amine acid acceptance values.4.3 This test method

13、may be used by producers and users toverify that a product is complying with acid acceptance productspecifications or by users to monitor the acid accepting abilityof a solvent in use.5. Test Method A5.1 Apparatus:5.1.1 Iodine or Erlenmeyer Flasks, 250 mL, with ground-glass stoppers.5.1.2 Burets, 25

14、 mL or 50 mL, graduated to 0.1 mL.5.1.3 Pipet, 10 mL and 25 mL.1This test method is under the jurisdiction of ASTM Committee D26 onHalogenated Organic Solvents and Fire Extinguishing Agents and is the directresponsibility of Subcommittee D26.04 on Test Methods.Current edition approved July 1, 2018.

15、Published July 2018. Originally approvedin 1971. Last previous edition approved in 2013 as D2942 02(2013). DOI:10.1520/D2942-02R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume informa

16、tion, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization

17、 established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16. Reagents6.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwis

18、e indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chemical Society,where such specifications are available.3Other grades may beused, provided it is first ascertained that the reagent is ofsufficiently high purity

19、 to permit its use without lessening theaccuracy of the determination.6.2 Purity of WaterUnless otherwise indicated, referencesto water shall be understood to mean reagent water conformingto Specification D1193.6.3 Bromophenol Blue Indicator Solution (1.0 g/L)Prepare by dissolving 1.0 g of bromophen

20、ol blue in a mixtureof 800 mLof water and 200 mLof denatured ethyl alcohol.ThepH range is 3.0 to 4.6. The color change is from yellow on theacid side to blue-green on the alkaline side.6.4 Hydrochlorination Reagent (0.1 N HCl)Prepare bydissolving 4.4 mL of concentrated hydrochloric acid (sp gr1.19)

21、in isopropyl alcohol and diluting to 500 mL withisopropyl alcohol.6.5 Sodium Hydroxide, Standard Solution (0.1 N)Prepareand standardize in accordance with Practice E200.7. Safety Precautions7.1 Solvent HazardContact with the skin should beavoided to prevent the removal of natural oils.7.2 Observe th

22、e published safety procedures when handlingthe concentrated HCl and NaOH solutions.8. Procedure8.1 BlankPipet 25 mL of hydrochlorination reagent and25 mL of isopropyl alcohol with 25-mL pipets into a 250-mLErlenmeyer flask. Add 3 drops of bromophenol blue indicatorsolution and titrate to a stable bl

23、ue-green end point with 0.1 NNaOH solution. Record the millilitres of NaOH solutionrequired as A (see Section 9 for calculation).8.2 SampleTransfer 25 mL of hydrochlorination reagentby means of a 25-mL pipet to a 250-mL glass-stopperedErlenmeyer flask. Add 10 mL of dry halogenated solvent and25 mL o

24、f isopropyl alcohol. Shake the mixture thoroughly andallow to stand at room temperature for 10 min. Add 3 drops ofbromophenol blue indicator solution to the sample flask andtitrate with 0.1 N NaOH solution to the blue-green end point.Record the millilitres of NaOH solution required as B (seeSection

25、9 for calculation).NOTE 1Make sure flask and pipette are dry before running analysis.If turbidity or phase separation occurs, add a small amount of isopropanol.8.3 If the amount of nonamine acid acceptance must beknown, first determine the amine acid acceptance in accor-dance with Test Methods D2106

26、.9. Calculation9.1 Total Acid AcceptanceCalculate the total acid accep-tance as equivalent NaOH in weight % as follows:Equivalent NaOH weight, % 5 A 2 B!N 30.04 3100#/W (1)where:A = NaOH solution required for blank titration (8.1), mL,B = NaOH solution required for sample titration (8.2),mL,N = Norm

27、ality of NaOH solution,0.04 = G equivalent NaOH per mLof 1 normal solution, andW = sample used (volume in mL specific gravity), g.9.2 Nonamine Acid AcceptanceCalculate the nonamineacid acceptance as equivalent NaOH in weight % as follows:Equivalent NaOH, weight % (2)5 total acid acceptance 2 amine a

28、cid acceptance.10. Precision and Bias10.1 The precision limits of this test method have beendetermined as 0.01 % (equivalent NaOH, weight %).10.2 The bias of this test method has not been determined.11. Test Method B11.1 Determine the weight % of the acid acceptor (typicallyan epoxide, amines may al

29、so contribute acid acceptance)present by a validated method such as gas chromatography,density or refractive index. It will be necessary to calibrate theinstrumentation with known standards of the acid acceptor.11.2 If the acid acceptor is unknown, it can be identified byGC mass spectroscopy.11.3 Ca

30、lculate the acid acceptance by the following for-mula:Equivalent NaOH, weight, % 540 X wt % acid acceptorMW(3)where:40 = the molecular weight of NaOH, andMW = the molecular weight of the acid acceptor.12. Precision and Bias12.1 A bias of 102 to 105 % of acid acceptance, as com-pared to determining a

31、cid acceptance by Method A is notuncommon as the yield of acid acceptance from the acidacceptor by MethodAis commonly 95 to 98 %.This is actuallydue to a low bias (95 to 98 %) of Method A rather than highreporting by Method B.12.2 A Relative Standard Deviation of about 0.8 % can beexpected when the

32、weight percent acid acceptor is determinedby gas chromatography. The precision of the acid acceptancewill be the same as the precision of the weight percent acidacceptor.3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the tes

33、ting of reagents notlisted by the American Chemical Society, see Analar Standards for LaboratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.D2942 02 (2018)213. Keywords13.1 acid acceptanc

34、e; halogenated organic solvents; sol-vents; total acid acceptanceASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any su

35、ch patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invit

36、ed either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a

37、 fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this

38、 standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 02 (2018)3

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1