ASTM D3141 D3141M-2009(2014) Standard Specification for Asphalt for Undersealing Portland-Cement Concrete Pavements《底部填封硅酸盐水泥混凝土路面用沥青的标准规格》.pdf

1、Designation: D3141/D3141M 09 (Reapproved 2014)Standard Specification forAsphalt for Undersealing Portland-Cement ConcretePavements1This standard is issued under the fixed designation D3141/D3141M; the number immediately following the designation indicates theyear of original adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers asphalt suitable for underseal-ing portland cement concrete and ov

3、erlaid concrete pavementsby pumping hot asphalt under the slabs.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combini

4、ngvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2D5 Test Method for Penetration of Bituminous MaterialsD6 Test Method for Loss on Heating of Oil and AsphalticCompoundsD36 Test Method for Softening Point of Bitumen (Ring-and-Ball

5、Apparatus)D92 Test Method for Flash and Fire Points by ClevelandOpen Cup TesterD113 Test Method for Ductility of Bituminous MaterialsD140 Practice for Sampling Bituminous MaterialsD312 Specification for Asphalt Used in RoofingD2042 Test Method for Solubility of Asphalt Materials inTrichloroethylene3

6、. Material3.1 An asphalt of suitable consistency for pumping whenheated to a temperature from 204 to 232C 400 to 450F andfor resistance to displacement in the pavement when cooled;for sealing the underside of the slabs and joints, to fill cavities;and to correct vertical alignment by raising the sla

7、b.4. Properties4.1 The asphalt shall be homogeneous and free of water andshall conform to the requirements in Table 1.5. Methods of Sampling and Testing5.1 The asphalt shall be sampled and the properties enumer-ated in this specification shall be determined in accordancewith the following ASTM metho

8、ds:5.1.1 SamplingPractice D140.5.1.2 Softening PointTest Method D36.5.1.3 Flash PointTest Method D92.5.1.4 PenetrationTest Method D5.5.1.5 DuctilityTest Method D113.5.1.6 Loss on HeatingTest Method D6.5.1.7 Bitumen Soluble in TrichloroethyleneTest MethodD2042.6. Keywords6.1 asphalt cement; portland-

9、cement concrete; undersealing1This specification is under the jurisdiction of ASTM Committee D04 on Roadand Paving Materials and is the direct responsibility of Subcommittee D04.40 onAsphalt Specifications.Current edition approved June 1, 2014. Published October 2014. Originallyapproved in 1972. Las

10、t previous edition approved in 2009 as D3141/D3141M 09.DOI: 10.1520/D3141_D3141M-09R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summar

11、y page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this

12、standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years

13、 andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committe

14、e, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-

15、2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the stand

16、ard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Requirements for Asphalt for Undersealing PortlandCement Concrete PavementsNOTE 1These requirements are the same as for Type III asphalt inSpecification D312.min maxSoftening point, C F 85 185 96 205Flash point, C F 260 500 .Penetration, units:at 0C 32F 6 .at 25C 77F 15 35at 46C 115F . 90Ductility at 25C 77F, cm 2.5 .Solubility in trichloroethylene, % 99 .D3141/D3141M 09 (2014)2