ASTM D3311-2009a Standard Specification for Drain Waste and Vent (DWV) Plastic Fittings Patterns《排水 废水及通风(DWV)塑料管配件图样的标准规范》.pdf

1、Designation: D 3311 09aAn American National StandardStandard Specification forDrain, Waste, and Vent (DWV) Plastic Fittings Patterns1This standard is issued under the fixed designation D 3311; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification provides standard fitting geometriesand laying lengths for plastic fittings

3、intended for use in drain,waste, and vent applications. (See Specifications D 2661 andD 2665.)1.2 Fittings meeting the requirements of this standard speci-fication are designed for use with outside diameter controlledpipe. The inside diameter can vary significantly as the wallthickness and outside d

4、iameter varies and therefore is notsuitable for use as a fitting socket.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced

5、 Documents2.1 ASTM Standards:2D 2661 Specification for Acrylonitrile-Butadiene-Styrene(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipeand FittingsD 2665 Specification for Poly(Vinyl Chloride) (PVC) Plas-tic Drain, Waste, and Vent Pipe and Fittings3. Requirements3.1 Fittings shall conform to the

6、 geometries and layinglengths as shown in Tables 1-46 and Fig. 1. Tolerances shall be6116 in. unless otherwise specified.3.2 Spigot and hub dimensions shall conform to the require-ments of the referencing standard.3.3 The exact outside shape of a fitting is not determined bythe outline drawings show

7、n in this specification but rather bythe socket dimensions, wall thickness requirements, waterway,laying lengths, and any other critical dimensions that may bespecified.3.4 The pitch of sockets for patterns with 90 angles (exceptvent fittings) shall be14 in./ft or 1 12 min.3.5 On double reducing san

8、itary tees, the G2 dimension onbranches will be calculated on the larger size and centerlinesshall remain the same for both branches.3.6 All other dimensions, materials and property require-ments shall be in conformance with the referencing standard.4. Keywords4.1 DWV; fittings; plastic; Schedule 40

9、; thermoplastic1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved Aug. 1, 2009. Published August 2009. Originallyapproved in 1974. Last previous edition approved in 2009

10、as D 3311 09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the en

11、d of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.TABLE 1 Bends, in. (mm)Nominal Pipe Size14 BendLong Sweep14 Bend18 Bend16 Bend116 BendGGGGG114 1916 (40) 214 (57) 1 (25)78 (22)716 (11)112 134 (44) 234 (70) 118 (29) 1

12、 (25)12 (13)22516 (59) 314 (83) 112 (38) 1516 (33)1116 (17)33116 (78) 4116 (103) 134 (44) 11116 (43)1316 (21)4378 (98) 41516 (125) 2316 (56) 2116 (52) 1 (25)6 5 (min) (127) 9 (229) 2 (min) (51) 338 (86) 112 (38)8 6 (152) . . . 2116 (52) . . . 112 (38)TABLE 2 Bends with Inlets, in. (mm)Nominal Pipe S

13、ize14 Bend with Low Heel InletLong-Sweep14 Bend with Low HeelInletLong-Sweep14 Bend with High Heel InletGN G N G NG3by3by112 3116 (78) 4316 (106) 4116 (103) 434 (121) . . . . . . . . .3by3by2 3116 (78) 4716 (113) 4116 (103) 41516 (125) 4116 (103) 558 (143) 214 (57)4by4by2 378 (98) 5716 (138) 41516 (

14、125) 6 (152) . . . . . . . . .D 3311 09a2TABLE 3 Sanitary Tees, 45 Wyes, Combination Wyes and18 Bends, in. (mm)Nominal Pipe SizeSanitary Tee Single and DoubleA45 Wye, Single and DoubleCombination Wye and 1/8 Bend Single andDoubleGN GJ GN GJ GN GJ11434 (19) 1916 (40) 1116 (27) 2916 (65)716 (11) 21516

15、 (75)112 1 (25) 134 (44) 118 (29) 278 (73)12 (13) 338 (86)2138 (35) 2516 (59) 138 (35) 358 (92) 1 (25) 412 (114)311316 (46) 3116 (78) 158 (41) 5 (127) 118 (29) 6516 (160)4214 (57) 378 (98) 178 (48) 638 (162) 11316 (46) 858 (219)6312 (89) 5 (127) 134 (44) 8716 (214)BB8412 (114) 6 (152) 238 (60) 1134

16、(298)ANon-reducing double sanitary tees are for vent use only.BCombination wye and18 bend is assembled from two standard fittings.TABLE 4 Reducing Sanitary Tees, 45 Wyes, Combination Wyes, and18 Bends, in. (mm)Nominal Pipe SizeSanitary Tee, Reducing Single and DoubleA45 Wye, Reducing Single and Doub

17、leCombination Wye and18 Bend ReducingSingle and DoubleG1 G2 G3 G4 G1 G2 G3 G1 G2 G3112 by 114 by 1141116 (17)B112 (38)B11116 (43)B11116 (43)B112 by 114 by 112 1 (25) 134 (44) 134 (44) 134 ()112 by 112 by 1141316 (21) 11116 (43) 11316 (46) 11316 (46) 12 (13) 314 (83) 3316 (81)2by114 by 112 1316 (30)

18、11516 (49) 2316 (56) 2316 (56)2by112 by 112 1316 (30) 11516 (49) 2316 (56) 2316 (56)34 (19)B21316 (71)B21516 (75)B 916 (14) 31116 (94) 358 (92)2by112 by 2 138 (35) 2516 (59) 2516 (59) 2516 (50) 1 (25)B312 (89)B338 (86)B1 (25) 412 (114) 412 (114)2by2by114 1316 (30) 11516 (49) 2316 (56) 2316 (6)2by2by

19、112 1316 (30) 11516 (49) 2316 (56) 2316 (56) 1116 (27) 3516 (84) 3716 (87)916 (14) 31116 (170) 358 (92)3by3by1121516 (24) 134 (44) 2916 (65) 2916 (65)12 (13) 334 (95) 4516 (110)18 (3) 3716 (87) 414 (108)3by3by2 1316 (30) 218 (54) 278 (73) 278 (73)78 (22) 418 (105) 458 (117)716 (11) 434 (121) 5516 (1

20、35)3by3by2by1121516 (24)B2116 (52)B2716 (62)B212 (64)B4by4by112 1116 (27)B2 (51)B314 (83)B314 (83)B0(0)B3516 (84)B31516 (100)B4by4by2 118 (29) 2116 (52) 3516 (84) 3516 (84)38 (10) 41116 (119) 5916 (141)516 (8) 434 (121) 578 (149)4by4by3 134 (44) 3 (76) 3916 (90) 3916 (90) 1116 (27) 5916 (141) 6 (152

21、) 1116 (27) 638 (162) 678 (175)6by6by3 316 (5)B61516 (176)B7716 (189)B 1116 (17)B71316 (198)B81316 (224)B6by6by4 2316 (56)B358 (92)B4516 (110)B4516 (110)B 316 (5)B61116 (170)B7716 (189)B 916 (14)B71316 (198)B81516 (227)B8by8by4 258 (67) 418 (105) 514 (133) 514 (133)38 (10) 758 (194) 858 (219)CCC8by8

22、by6 3916 (90) 41316 (122) 512 (140) 512 (140) 1 (25) 912 (241) 91316 (249)ANon-reducing double sanitary tees are for vent use only.BThis dimension is a minimum with no upper maximum limit.CCombination Wye and18 bend is assembled from two standard fittings.D 3311 09a3TABLE 5 60 Wyes, Single, and Doub

23、le, in. (mm)Nominal PipeSizeGN GJ112 118 (40) 278 (73)2138 (37) 358 (92)3158 (37) 5 (127)TABLE 6 Fixture Tees, in. (mm)Nominal Pipe Size G1 G2 G3112 1916 (40) 1316 (30) 114 (32)2by112 by 112 1716 (37) 1316 (30) 114 (32)2by2by112 1716 (37) 1516 (33) 114 (32)TABLE 7 Cleanout Tees, in. (mm)Nominal Pipe

24、SizeGI112 1316 (30)58 (16)2112 (38)58 (16)3178 (48)34 (19)4212 (64)78 (22)TABLE 8 60 Reducing Wyes, Single and Double, in. (mm)Nominal PipeSizeG1 G2 G32by2by112 1116 (27) 3716 (87) 3716 (87)3by3by11212 (13) 334 (95) 4516 (110)3by3by278 (22) 418 (105) 458 (117)TABLE 9 Molded Nipples, in. (mm)NominalP

25、ipe SizeOD ID Length112231.9002.3753.5001.5001.9392.90012-in. increments fromclose to 18 in. longTABLE 10 Vent Tees and14 Bend Vents, in. (mm)Nominal PipeSizeVent Tee14 Bend Vent114 1 (25) 1 (25)112 1316 (30) 1316 (30)2112 (38) 112 (38)3178 (48) 178 (48)4212 (64) 212 (64)D 3311 09a4TABLE 11 Reducing

26、 Vent Tees, Single, and Double, in. (mm)Nominal Pipe Size GN GJ2by112 by 112 1316 (30) 112 (38)2by2by112 1316 (30) 112 (38)3by3by112 1316 (30) 178 (48)3by3by2 112 (38) 178 (48)TABLE 12 Bushings, in. (mm)Nominal PipeSizeStyle 1 (a and b)AStyle 2 Style 3L CM R L1 CM N L112 by 1141516 (24)316 (5)316 (5

27、) . . . 1(25)2by114 1116 (27)516 (8)316 (5) . . . 118 (29)2by112 1116 (27)516 (8)316 (5) . . . 1332 (28)3by112 134 (44) 1 (25)14 (6) 134 (44)34 (19)14 (6) 112 (38)3by2 134 (44)78 (22)14 (6) 134 (44)78 (22)14 (6) 158 (41)4by2 2(51) 118 (29)14 (6) 2 (51)78 (22)14 (6) .4by3 2(51)12 (13)14 (6) 2 (51) 11

28、2 (38)14 (6) .6by3 3516 (84) 11316 (97)516 (8) . . . .6by4 312 (89) 134 (44)12 (13) . . . .8by4 458 (117) 278 (73)58 (16) . . . .8by6 458 (117) 158 (41)58 (16) . . . .ANo less than four ribs shall be used to support walls.D 3311 09a5TABLE 13 Couplings, Adapters, in. (mm)Nominal Pipe SizeCoupling Fem

29、ale Adapter Male AdapterFemale FittingAdapterDN,min N,min N,min A, max N,min114 1.600 to 1.38018 (3)14 (6)316 (5) 1.290 (32.77)532 (4)112 1.840 to 1.61018 (3)14 (6)316 (5) 1.552 (39.42)532 (4)2 2.320 to 2.06718 (3)14 (6)316 (5) 2.067 (52.50)532 (4)3 3.440 to 3.068316 (5)516 (8)38 (10) 3.068 (77.93)7

30、32 (6)4 4.440 to 4.02614 (6)1132 (9)38 (10) 4.026 (102.26)14 (6)6 6.550 to 6.06514 (6) . . . .8 8.655 to 8.61014 (6) . . . .TABLE 14 Pipe Increasers, in. (mm)NominalPipe SizeN,min114 by 1121332 (10)112 by 21732 (13)112 by 3 1332 (28)2by378 (22)2by4 138 (35)3by41516 (24)D 3311 09a6TABLE 15 Trap Adapt

31、ers, in. (mm)Without stop With StopNominalPipe SizeN,min A,min114316 (5) 1.250 (32)112316 (5) 1.500 (38)2316 (5) 2.000 (51)114 by 112316 (5) 1.250 (32)TABLE 16 Pipe Plugs, in. (mm)NominalPipe SizeIWQ11412 (13) 1 (25) 1 (25)11258 (16) 138 (35) 1 (25)258 (16) 138 (35) 114 (32)21234 (19) 112 (38) 114 (

32、32)334 (19) 134 (44) 158 (41)31234 (19) 134 (44) 158 (41)478 (22) 178 (48) 2 (51)6 1 (25) 2 (51) 214 (32)8138 (35) 238 (60) 312 (89)D 3311 09a7TABLE 17 Hubs, in. (mm)NominalPipe SizeACNAJCJN2 . . . 2.94(74.7) 238 (60)38 (10)3 3.448 (87.58) 11116 (43)516 (8) 3.94 (100.1) 258 (67)716 (11)4 4.493 (114.

33、12) 11516 (49)1132 (9) 4.94 (125.5) 278 (73)12 (13)Reducing 4 by 3 4.493 (114.12) 11516 (49)516 (8) 4.94 (125.5) 278 (73)716 (11)TABLE 18 Spigots, in. (mm)NominalPipe SizeL2,min L1,min L3,minMANmax min2312 (89) 458 (117)38 (10) 2.75 (69.9) 2.63 (66.8) 2.00 (50.8)3334 (95) 558 (143)38 (10) 3.88 (98.6

34、) 3.63 (92.2) 3.00 (76.2)4 4 (102) 618 (156)38 (10) 4.88 (124.0) 4.63 (117.6) 4.00 (101.6)D 3311 09a8TABLE 19 Reducing Spigots, in. (mm)NominalPipe SizeL2 min L1 min L3 minMAJmax min2by112 312 (89) 414 (108)38 (10) 2.75 (69.9) 2.63 (66.8) 2.00 (50.8)3by112 334 (95) 412 (114)38 (10) 3.88 (98.6) 3.63

35、(92.2) 3.00 (76.2)3by2 334 (95) 458 (117)38 (10) 3.88 (98.6) 3.63 (92.2) 3.00 (76.2)4 by 2 4 (102) 478 (124)38 (10) 4.88 (124.0) 4.63 (117.6) 4.00 (101.6)4 by 3 4 (102) 512 (140)38 (10) 4.88 (124.0) 4.63 (117.6) 4.00 (101.6)TABLE 20 P Traps, in. (mm)NominalPipe Sizemin GJ min GGJ min GGN min GN min

36、R114 418 (105) 338 (86) 3 (76) 138 (35) 158 (41)112 4732 (107) 358 (92) 3 (76) 138 (35) 158 (41)2714 (184) 4116 (103) 5 (127) 214 (57) 212 (64)38716 (214) 6516 (160) 614 (159) 258 (67) 318 (79)4101316 (275) 778 (200) 8116 (205) 3716 (87) 4116 (103)D 3311 09a9TABLE 21 Double Fixture Fitting, in. (mm)

37、Nominal Pipe Size G1 G2 G3 G411238 (10) 3916 (90) 2716 (62) 2716 (62)238 (10) 4916 (116) 3116 (78) 3116 (78)312 (13) 634 (171) 412 (114) 412 (114)Reducing:2by112 by 112 by 11238 (10) 3916 (90) 2716 (62) 2716 (62)2by112 by2by238 (10) 4916 (116) 3116 (78) 3116 (78)2by112 by2by11238 (10) 4916 (116) 311

38、6 (78) 3116 (78)TABLE 22 Double Fixture Fitting, in. (mm)Interchanges with Double Fixture FittingsNominalPipe SizeDouble Fixture FittingG1 G2 G3 G4 R1 R211238 (10) 318 (79) 21116 (68) 21116 (68) 358 (92) 358 (92)238 (10) 414 (108) 312 (89) 312 (89) 412 (114) 412 (114)312 (13) 614 (159) 41516 (125) 4

39、1516 (125) 658 (168) 658 (168)Reducing2by112 by 112 by11238 (10) 318 (79) 278 (73) 278 (73) 358 (92) 358 (92)2by112 by 112 by 238 (10) 414 (108) 278 (73) 312 (69) 358 (92) 412 (114)2by112 by2by238 (10) 414 (108) 312 (89) 312 (89) 412 (114) 412 (114)3by2by3by312 (13) 614 (159) 41516 (125) 41516 (125)

40、 658 (168) 658 (168)D 3311 09a10TABLE 23 Single and Double Long Turn Tee, in. (mm)Interchanges with Combination Wye 1/8 BendNominalPipe SizeSingle and Double Long Turn TeeG1 G2 N R11438 (10) 3716 (87) 3116 (78) 434 (121)112716 (11) 31516 (100) 312 (89) 578 (149)21116 (17) 518 (130) 4716 (113) 7 (178

41、)31116 (27) 7916 (192) 612 (165) 1018 (257)4112 (38) 10 (254) 812 (216) 1314 (337)6212 (64) 1538 (391) 1278 (327) 19 (483)TABLE 24 Single and Double Long Turn Tee Reducing, in. (mm)Interchanges with Reducing Combination Wye 1/8 BendNominal Pipe SizeSingle and Double Long Turn Tee ReducingG1 G3 N G2

42、R112 by 114 by 11438 (10) 358 (92) 3116 (78) 3716 (87) 434 (121)112 by 112 by 11438 (10) 358 (92) 3116 (78) 3716 (87) 434 (121)2by112 by 112716 (11) 4316 (107) 312 (89) 31516 (100) 578 (200)2by112 by 21116 (17) 518 (130) 4716 (113) 518 (130) 7 (178)2by2by11438 (10) 31316 (97) 3116 (78) 3716 (87) 434

43、 (121)2by2by112716 (11) 4316 (102) 312 (89) 31516 (100) 578 (149)3by3by112716 (11) 434 (121) 312 (89) 31516 (100) 578 (149)3by3by21116 (17) 51116 (128) 4716 (113) 518 (130) 7 (178)4by4by11238 (10) 5316 (132) 3916 (90) 31516 (100) 578 (149)4by4by258 (16) 618 (156) 412 (114) 518 (130) 7 (178)4by4by3 1

44、116 (27) 8116 (205) 612 (165) 7916 (192) 1018 (257)6by6by2916 (14) 718 (181) 4916 (116) 518 (130) 7 (178)6by6by31516 (24) 9116 (230) 658 (168) 7916 (192) 1018 (257)6by6by4 112 (38) 11 (279) 812 (216) 10 (254) 1314 (337)6by6by5 2(51) 13516 (338) 1034 (273) 1234 (324) 16 (406)D 3311 09a11TABLE 25 Thre

45、e-Way EII, in. (mm)NominalPipe SizeG1 G2 G3112 134 (44) 134 (44) 134 (44)22516 (59) 2516 (59) 2516 (59)33116 (78) 3116 (78) 3116 (78)4378 (98) 378 (98) 378 (98)Reducing2by112 by 112 (short) 158 (41) 158 (41) 158 (41)3by2by3 3116 (78) 278 (73) 3116 (78)2by112 by 112 (long) 11516 (49) 2316 (56) 2316 (

46、56)TABLE 26 Two Way Cleanout, in. (mm)Nominal Pipe Size G344116 (103)41516 (125)D 3311 09a12TABLE 27 Sanitary Tees, with Side Inlet, in. (mm)Nominal Pipe Size G1 G2 G3 G4 G5Left-Hand Side Inlet112 by 112 by 112 by 112 234 (70) 134 (44) 134 (44) 134 (44) 134 (44)2by2by112 by 112 31116 (94) 2516 (59)

47、2516 (59) 2516 (59) 2516 (59)3by3by2by112 3516 (84) 218 (54) 278 (73) 2916 (65) 218 (54)3by3by2by2 3516 (84) 218 (54) 278 (73) 278 (73) 218 (54)3by3by3by112 478 (124) 3116 (78) 3116 (78) 2916 (65) 31116 (94)3by3by3by2 478 (124) 3116 (78) 3116 (78) 278 (73) 31116 (94)4by4by4by2 618 (156) 378 (98) 378 (98) 3516 (84) 5 (127)Right-Hand Side Inlet3by3by2by112 3516 (84) 218 (54) 278 (73) 29