1、Designation: D3335 85a (Reapproved 2014)Standard Test Method forLow Concentrations of Lead, Cadmium, and Cobalt in Paintby Atomic Absorption Spectroscopy1This standard is issued under the fixed designation D3335; the number immediately following the designation indicates the year oforiginal adoption
2、 or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1.
3、 Scope1.1 This test method covers the determination of lead2contents between 0.01 and 5 %, cadmium contents between 50and 150 ppm (mg/kg), and cobalt contents between 50 and2000 ppm (mg/kg) present in the nonvolatile portion of liquidcoatings or contained in dried films. There is no reason tobelieve
4、 that higher levels of all three elements could not bedetermined by this test method, provided that appropriatedilutions and adjustments in specimen size and reagent quan-tities are made.1.2 Only pigmented coatings were used for evaluating thistest method, but there is no reason to believe that varn
5、ishes andlacquers could not be analyzed successfully, provided thatappropriate precautions are taken.1.3 This test method is not applicable to the determinationof lead in samples containing antimony pigments (low recov-eries are obtained).1.4 If lead is present in the sample to be analyzed in thefor
6、m of an organic lead compound at a concentration greaterthan 0.1 %, small losses of lead may occur, resulting in slightlypoorer precision than shown in Section 12.1.5 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.6 This sta
7、ndard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Specific hazardstatements
8、are given in Section 7.2. Referenced Documents2.1 ASTM Standards:3D1193 Specification for Reagent WaterD2832 Guide for Determining Volatile and Nonvolatile Con-tent of Paint and Related Coatings3. Summary of Test Method3.1 The specimen of liquid coating or dried film is preparedfor analysis by dry a
9、shing. The content of lead, cadmium, orcobalt of an acid extract of the ash is determined by atomicabsorption spectroscopy.4. Significance and Use4.1 The permissible level of heavy metals in certain coat-ings is specified by governmental regulatory agencies. This testmethod provides a fully document
10、ed procedure for determininglow concentrations of lead, cadmium, and cobalt present inboth water and solvent-reducible coatings to determine com-pliance.5. Apparatus5.1 Atomic Absorption Spectrophotometer, consisting of anatomizer and either a single- or three-slot burner; gas pressureregulating and
11、 metering devices for air and acetylene; lead,cadmium, and cobalt source lamps4with a regulated constant-current supply; a monochromator and associated optics; aphotosensitive detector connected to an electronic amplifier;and a readout device.1This test method is under the jurisdiction of ASTM Commi
12、ttee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.Current edition approved July 1, 2014. Published July 2014. Originally approvedin 1974. Last previous edition approved in 2009
13、as D3335 85a (2009). DOI:10.1520/D3335-85AR14.2Vandeberg, J. T., Swafford, H. D., and Scott, R. W., “Determination of LowConcentrations of Lead in Paint,” Journal of Paint Technology, Vol 47, No. 604,May 1975.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Custom
14、er Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Both hollow cathode lamps and electrodeless discharge lamps have been foundsatisfactory for this purpose.Copyright ASTM International, 100 Barr Harbor
15、Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.2 Muffle Furnace, capable of maintaining 500 6 10C.5.3 Crucibles, wide-form, porcelain, glazed inside and out-side except for the outside bottom surface, approximately30-mL capacity, 50-mm rim diameter and 31-mm height.55.4 Hot Pl
16、ate, with variable surface temperature controlover the range from 70 to 200C.5.5 High-Silica Glass Beakers,6100 and 250-mL.5.6 Volumetric Flasks, 50, 100, and 1000-mL.5.7 Dropping Bottles,14 or 7 or 15-mL (12-oz) capacity.5.8 Glass or Disposable Syringes, 5 or 10-mL capacity.5.9 Pipets, 1, 2, 5, and
17、 10-mL capacity.5.10 Paint Shaker.5.11 Paint Draw-Down Bar.6. Reagents6.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the American Chem
18、ical Society,where such specifications are available.7Other grades may beused, provided it is first ascertained that the reagent is ofsufficiently high purity to permit its use without lessening theaccuracy of the determination.6.2 Purity of WaterUnless otherwise indicated, referencesto water shall
19、be understood to mean reagent grade waterconforming to Type II of Specification D1193.6.3 Ammonium Acetate Solution (50 % weight/volume)Dissolve 500 g of ammonium acetate (NH4C2H3O2) in waterand dilute to 1 L.6.4 Ammonium Acetate Diluting SolutionAdd 50 mL ofHNO3(sp gr 1.42) to 150 mL of 50 % weight
20、/volumeammonium acetate solution and dilute to 1 L.6.5 Cadmium Standard Stock Solution (1 mg/mL)Dissolve 2.1032 g of cadmium nitrate (Cd(NO3)2)in10mLofwater, add 10 mL of HNO3(sp gr 1.42), and dilute to 1 L.6.6 Cobalt Standard Stock Solution (1 mg/mL)Dissolve4.9387 g of cobalt nitrate hexahydrate (C
21、o(NO3)26H2O) in 10mL of water, add 10 mL of HNO3(sp gr 1.42), and dilute to 1L.6.7 Lead Standard Stock Solution (1 mg/mL)Dissolve1.5980 g of lead nitrate (Pb(NO3)2) in 10 mL of water, add 10mL of HNO3(sp gr 1.42), and dilute to 1 L.NOTE 110.00 mg/mL concentrations of cadmium, lead, silver andzinc ar
22、e available as SRM 2121; and the same concentration of cobalt,copper, iron and nickel as SRM 2124 from: Office of Standard ReferenceMaterials, Room B-311, Chemistry Building, NIST, Washington, DC20234.6.8 Nitric Acid (sp gr 1.42)Concentrated nitric acid(HNO3).6.9 Nitric Acid (1+1)Add 1 volume of HNO
23、3(sp gr 1.42)to 1 volume of water.7. Hazards7.1 Concentrated nitric acid is corrosive and may causesevere burns of the skin or eyes; the vapor is irritating tomucous membranes. Use care in handling this acidic substance.Refer to suppliers Material Safety Data Sheet.7.2 Use only a rubber bulb aspirat
24、or for pipeting liquids.8. Calibration and Standardization8.1 Prepare 100-mL quantities of at least four standardsolutions bracketing the expected lead, cadmium, or cobaltconcentration in the sample to be tested. To suitable aliquots ofthe 1 mg/mL standard lead, cadmium, or cobalt solution, add 5mL
25、of HNO3(sp gr 1.42) and 15 mL of 50 % ammoniumacetate solution. Dilute to 100 mL with water.8.2 Operational instructions for atomic absorption spectro-photometers vary with different models. Consult the manufac-turers literature for establishing optimum conditions for thespecific instrument used.8.3
26、 Turn the instrument on and set the wavelength to the283.3-nm lead line, the 228.8-nm cadmium line, or the240.7-nm cobalt line. Apply the current recommended by themanufacturer to the lead, cadmium, or cobalt source lamp.Allow the instrument to warm up for about 15 min and set theslit width. Adjust
27、the air and acetylene pressure or flow ratesand ignite the burner in accordance with the manufacturersinstructions.8.4 Aspirate water to rinse the atomizer chamber. Aspirate astandard solution and make any necessary readjustment ininstrument parameters to obtain maximum absorption.8.5 Aspirate each
28、of the appropriate standard solutions andrecord the corresponding instrument readings. Aspirate waterbetween each standard.8.6 Construct a calibration curve on linear graph paper byplotting the absorbance versus concentration (micrograms permillilitre) for each standard solution. Alternatively, the
29、calibra-tion results may be stored in the instrument, if so equipped, andreadings made directly in concentration.9. Procedure9.1 If the sample is a liquid coating, mix it untilhomogeneous, preferably on a mechanical shaker. Determinethe nonvolatile content in accordance with Guide D2832.5The sole so
30、urce of supply of No. 25007 crucibles, known to the committee atthis time is Coors Manufacturer. If you are aware of alternative suppliers, pleaseprovide this information to ASTM International Headquarters. Your comments willreceive careful consideration at a meeting of the responsible technical com
31、mittee,1which you may attend.6The sole source of supply of Vycor beakers, known to the committee at thistime is Corning Glass Co., Houghton Park, Corning, NY 14831. If you are aware ofalternative suppliers, please provide this information to ASTM Headquarters. Yourcomments will receive careful consi
32、deration at a meeting of the responsibletechnical committee,1which you may attend.7Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing of reagents notlisted by the American Chemical Society, see Analar Standards for La
33、boratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.D3335 85a (2014)29.2 Prepare at least two replicate specimens by weighing bydifference from a dropping bottle or syringe approximately
34、2 to3 g of the mixed liquid coating, or by directly weighingapproximately 1 to2gofdried paint film, into a 30-mLporcelain crucible. Weigh to 0.1 mg.NOTE 2The specimen size called for will give a concentration ofapproximately 10 to 20 g/mL lead in the final diluted solution for paintscontaining appro
35、ximately 500 ppm (mg/kg) lead, based on the solids. Ifthe material is estimated to contain more or less than 500 ppm lead, thequantity taken should be adjusted accordingly. In the event that signifi-cantly less than 500 ppm lead is expected, a 250-mL high-silica beakermay be used in place of the cru
36、cible to accommodate specimen weights upto 10 g. The size specified will give a concentration of approximately 2 to4 g/mL cadmium in the final diluted solution for paints containingapproximately 100 ppm cadmium, based on the solids. The size specifiedwill give a concentration of approximately 10 to
37、20 g/mL cobalt in thefinal diluted solution for paints containing approximately 500 ppm cobalt,based on the solids.NOTE 3Recover dried paint films from previously coated substrates(being careful not to remove any underlying material from the substrate)or prepare in the laboratory from liquid samples
38、. For the laboratorypreparation, flow some of the well-mixed sample onto a clean glass plate.The use of a paint draw-down bar is recommended to obtain a uniform wetfilm thickness not exceeding 2 mils (50 m). Allow the film to dry in anoven at 105C for a minimum of 1 h. Scrape the dried film off the
39、glassplate, preferably with a single-edge razor blade.9.3 Place the crucible (or beaker) containing the liquidcoating on a hot plate and slowly increase the temperature untilthe material is dried. With some types of coatings, an initialoven-drying at 105C may be necessary to remove solventswithout i
40、ncurring losses due to spattering.9.4 When the specimen appears to be dry or when startingwith a dried film, gradually increase the temperature of the hotplate until the material chars.9.5 After charring is complete, place the container in apreheated muffle furnace and ash at 475 to 500C.NOTE 4Ashin
41、g at temperatures in excess of 500C may result in theloss of some lead by volatilization.9.6 When the ashing appears to be complete (do not exceed1 to 2 h), remove the crucible or beaker from the muffle furnaceand allow it to cool to room temperature. Break up the ash intofine particles with a glass
42、 stirring rod, leaving the rod with thecontainer through the filtering step.9.7 Add 10 mL of HNO3(1 + 1), taking care to avoid lossesdue to spattering in case the ash reacts vigorously with the acid.Heat carefully on a hot plate until 2 to 3 mL of solution remain.Add an additional 10 mLof HNO3(1 + 1
43、) and continue heatingon the hot plate until less than 5 mL of the solution remains.9.8 Filter the solution through medium-porosity filter paperinto a 50-mL volumetric flask. If the filtrate is not clear, refilterthrough fine-porosity filter paper. Wash the container threetimes with 2.5 mL of hot am
44、monium acetate solution (6.3),each time transferring the washings to the filter paper. Wash thefilter paper several times with water. Adjust the volume to 50mL with water and mix.9.9 Aspirate the test solution and determine the absorbancein the same manner in which the instrument was calibrated.Dete
45、rmine the concentration of lead, cadmium, or cobalt inmicrograms per millilitre from the calibration curve. If theabsorbance is above the range covered by the calibration curve,dilute an aliquot of the sample solution to a suitable volumewith ammonium acetate diluting solution.NOTE 5For maximum accu
46、racy, calibration and standardization(Section 8) should be completed just prior to aspirating the samplesolution.NOTE 6The method of standard additions may be used to improve theaccuracy of the analysis. This method is particularly recommended for usewith unknown samples where matrix effects may be
47、potentially signifi-cant. For a detailed description of the procedure and calculations used inthe method of standard additions, consult a standard text on atomicabsorption spectroscopy or the instruction manual provided by theinstrument manufacturer.10. Calculation10.1 Calculate the mean concentrati
48、on of lead, cadmium, orcobalt in the nonvolatile portion of the sample as follows:lead, cadmium or cobalt, ppm mg/kg! in nonvolatile (1)5C 3 F 35000!/NV 3 S!where:C = concentration of lead, cadmium, or cobalt in theaspirated specimen solution, (g/mL),F = dilution factor from 9.9 (volume diluted to/v
49、olumeof aliquot),5000 = factor derived from multiplying the 50-mL volumeobtained in procedure in 9.8 by 100 (to convert NVused to a whole number) and 106(to obtain ppm),then dividing by 106(to convert grams of sample tog),NV = percent nonvolatile of paint sample (use 100 ifsample was a dried film), andS = sample, g.11. Report11.1 Report the lead, cadmium, or cobalt content of thenonvolatile content of the sample and whether the analysis wasconducted on a liquid coating or a dried film.12. Precision and Bias812.1 The precision estimates are based o
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1