ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:77.62KB ,
资源ID:514806      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-514806.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D3452-2006(2017) Standard Practice for Rubber&x2014 Identification by Pyrolysis-Gas Chromatography《采用裂解气相色谱法识别橡胶的标准实施规程》.pdf)为本站会员(proposalcash356)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D3452-2006(2017) Standard Practice for Rubber&x2014 Identification by Pyrolysis-Gas Chromatography《采用裂解气相色谱法识别橡胶的标准实施规程》.pdf

1、Designation: D3452 06 (Reapproved 2017)Standard Practice forRubberIdentification by Pyrolysis-Gas Chromatography1This standard is issued under the fixed designation D3452; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.PART 1. IDENTIFICATION OF SINGLE POLYMERS1.

3、 Scope1.1 This practice covers the identification of polymers inraw rubbers, and cured and uncured compounds, based on asingle polymer, by the gas chromatographic patterns of theirpyrolysis products (pyrograms). Implementation of this guidepresupposes a working knowledge of the principles and tech-n

4、iques of gas chromatography, sufficient to carry out thispractice and to interpret the results correctly.21.2 This practice will identify the following polymers:1.2.1 Polyisoprene of natural or synthetic origin,1.2.2 Butadiene-styrene copolymers,1.2.3 Polybutadiene,1.2.4 Polychloroprene,1.2.5 Butadi

5、ene-acrylonitrile copolymers,1.2.6 Ethylene-propylene copolymers and relatedterpolymers, and1.2.7 Isobutene-isoprene copolymers.1.3 This practice will not differentiate the following poly-mers:1.3.1 Natural polyisoprene from synthetic polyisoprene.1.3.2 Butadiene-styrene copolymers produced by solut

6、ionand emulsion polymerization. It is sometimes possible todistinguish butadiene-styrene copolymers containing differentamounts of styrene as well as random polymers from blockpolymers.1.3.3 Polybutadiene with different microstructures.1.3.4 Different types of polychloroprenes.1.3.5 Butadiene-acrylo

7、nitrile copolymers with differentmonomer ratios.1.3.6 Ethylene-propylene copolymers with different mono-mer ratios, as well as the copolymers from the related terpoly-mers.1.3.7 Isobutene-isoprene copolymers (butyl rubbers) fromhalogenated butyl rubbers.1.3.8 Polyisoprene containing different amount

8、s of cis-transisomers.1.3.9 The practice does not identify ebonite or hard rubbers.1.4 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with

9、 its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on stan

10、dard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:3D297 Test Methods for Rubber ProductsChemical

11、 Analy-sisE260 Practice for Packed Column Gas ChromatographyE355 Practice for Gas Chromatography Terms and Relation-ships3. Significance and Use3.1 For research, development, and quality controlpurposes, it is advantageous to determine the composition ofrubbers in cured, compounded products.1This pr

12、actice is under the jurisdiction of ASTM Committee D11 on Rubber andRubber-like Materials and is the direct responsibility of Subcommittee D11.11 onChemical Analysis.Current edition approved May 1, 2017. Published May 2017. Originallyapproved in 1975. Last previous edition approved in 2012 as D3452

13、06 (2012).DOI: 10.1520/D3452-06R17.2Definitions of terms and general directions for the use of gas chromatographymay be found in Practices E355 and E260.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMSt

14、andards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized princip

15、les on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13.2 This practice provides such composition analysis, uti-lizing a gas chroma

16、tograph and pyrolysis products from rubberdecomposition.4. Principle of the Practice4.1 This practice is based upon comparison of the gaschromatographic pattern of the pyrolysis products of a knownrubber with an unknown rubber. The results of this separationwill hereafter be referred to as the pyrog

17、ram.4.2 The pyrogram of the known rubber is filed for futurereference. The pyrogram of the unknown rubber is compared tothis for identification.4.3 The success of the method depends upon examining theknown and unknown rubbers under exactly the same experi-mental conditions.4.4 The qualitative compos

18、ition of the pyrolysis productsdepend upon the type of polymer being studied.4.5 The quantitative composition of the pyrolysis productsmay be affected by the degree of cure, and recipe used, etc., butthe most important factor is the type of pyrolysis device.5. Apparatus5.1 Pyrolysis DevicesThe appli

19、cability of this practice hasbeen checked on the following types:5.1.1 Quartz Tubes, electrically heated at a prefixed tem-perature. The volatile products enter the chromatographthrough heated tubing.5.1.2 Platinum Filaments, electrically heated. Pyrolysis iscarried out within the chromatograph inle

20、t and immediatelyswept into the column by the carrier gas.5.1.3 Small Coils of Ferromagnetic Wire, heated to theCurie point temperature. The volatile products enter the gaschromatograph through heated tubing.5.2 Gas ChromatographThe applicability of this practicehas been checked on a wide variety of

21、 gas chromatographs,employing both flame ionization and thermal conductivitydetectors. Any commercially available instrument is satisfac-tory. Dual-column operation and temperature programming isstrongly recommended, but not mandatory.5.3 Gas Chromatographic ColumnsThe applicability ofthis practice

22、has been checked on a wide variety of columnlengths, diameters, supports, and liquid phases. The onlyrequisite is that there be sharp separation between the follow-ing: isobutene, butadiene, isoprene, vinylcyclohexene, styrene,and dipentene.5.4 Carrier GasThe applicability of this practice has beenc

23、hecked with both helium and nitrogen as the carrier gas. Bothare satisfactory.6. Sample Size6.1 For thermal conductivity detection and electricallyheated platinum filaments, a sample size of approximately3 mg has been found satisfactory. This could be increased ordecreased depending on the compositi

24、on of the sample and thecapacity of the probe.6.2 For flame ionization and either Curie point apparatus orelectrically heated platinum filaments, a sample size rangingfrom 0.2 to 2.0 mg has been found satisfactory.7. Procedure7.1 ExtractionAlthough not mandatory, some benefitsmay be obtained from ex

25、traction of the sample according toTest Methods D297, Sections 18 and 25. If the sample has beenextracted prior to obtaining the pyrogram, the known must alsobe extracted.7.2 PyrolysisThe following conditions apply to the threetypes of pyrolysis devices in 5.1:7.2.1 Quartz Tubes (5.1.1)Place 1 to 5

26、mg of sample in asmall quartz or porcelain boat in the cold part of the pyrolysistube. Stopper the tube and flush with carrier gas. Transfer theboat to the hot part of the tube, maintained at 500 to 800C.Length of the time depends upon the pyrolysis device;however, time and temperature must be kept

27、constant. Tominimize condensation, convey the volatile pyrolysis productsinto the gas chromatograph through tubing heated to a known,fixed temperature, but slightly higher than the gas chromato-graph inlet. Record the pyrogram.7.2.2 Electrically Heated Platinum Filaments(5.1.2)Place the required amo

28、unt of sample in the pyrolysisprobe. Insert it into the injection port of the gas chromatographand allow the base line to stabilize. Energize the probe, usingthe procedure recommended by the manufacturer of the unit toobtain temperatures of 800 to 1200C.7.2.3 Curie Point Apparatus (5.1.3)Place the r

29、equiredamount of sample in the coils of ferromagnetic wire or wrapthe wire securely around the required amount of sample andpyrolyze according to the manufacturers directions for properuse of the unit. Energize the apparatus to obtain the requiredtemperature of 550 to 650C (depending on the composit

30、ion ofthe alloy used for the wire) and introduce the pyrolysisproducts into the gas chromatograph. Record the pyrogram.7.3 Separation of the Volatile Pyrolysis ComponentsAsstated in 5.3, a wide variety of columns may be used. As anexample, the following describes the separation of volatilepyrolysis

31、components by means of suitable columns. Analysisof the products of polyisoprene pyrolysis are used in thisexample. In all cases, equivalent materials may be used.7.3.1 Polar Liquid PhaseStainless steel tubing, 4 to 6 mlong, with an outside diameter of 3.2 mm (18 in.), packed with10 to 20 % di(2-eth

32、ylhexyl)sebacate on a 150 to 180-mdiatomaceous silica support.4Carrier gas flow of 0.2 to0.3 cm3/s. Inlet and detector temperature at 170C. Oventemperature 50C isothermal until isoprene is completelyeluted, then program at 20 to 40C/min to 150C and maintainat this temperature until the dipentene is

33、eluted.7.3.2 Non-Polar Liquid PhaseStainless steel tubing, 3 mlong, with an outside diameter of 3.2 mm (18 in.), packed with4The sole source of supply of diatomaceous silica (Chromosorb P) known to thecommittee at this time is Johns-Manville Products Corp., Celite Div., 22 E. 40th St.,NY, NY 10016.

34、If you are aware of alternative suppliers, please provide thisinformation to ASTM International Headquarters. Your comments will receivecareful consideration at a meeting of the responsible technical committee,1whichyou may attend.D3452 06 (2017)210 % high vacuum grease on a 150 to 180-m diatomaceou

35、ssilica support. Carrier gas flow of 0.12 to 0.83 cm3/s. Inlettemperature of 170 to 200C. Oven temperature at 50Cisothermal for 3 min or until isoprene is eluted, then raise thetemperature to 130 to 150C at 4 to 6C/min. Maintain at thehigher temperature until the dipentene is eluted.8. Rubber Identi

36、fication (Interpretation of the Pyrogram)8.1 Each rubber type shows a distinctive pyrogram, underthe same pyrolysis and gas chromatographic conditions.8.2 Identification is achieved by comparing the pyrogram ofthe sample rubber (unknown) to the pyrogram of the knownrubber, under exactly the same ope

37、rating conditions.8.3 Some rubbers produce very characteristic hydrocarbonsand their identification is relatively easy. Examples of this typeare:8.3.1 Polyisoprene rubbers, which yield mainly isopreneand dipentene.8.3.2 Butadiene-styrene copolymers, which yield mainlybutadiene, vinyl cyclohexene, an

38、d styrene.8.3.3 Polybutadiene rubbers, which yield mainly butadieneand vinyl cyclohexene.8.3.4 Isobutene-isoprene copolymers, which yield mainlyisobutylene.8.4 Some rubbers do not yield very characteristic hydrocar-bons. Careful inspection of the pyrogram is required. Supple-mentary tests, such as t

39、hose for halogen and nitrogen may bean aid to more definite identification.8.5 It is recommended that, in addition to maintaining alibrary of pyrograms, the analyst compare the unknown samplewith a known, which appears most like his unknown, at thetime of analysis. In this manner, slight variations

40、in operatingparameters, which might influence the pyrogram, might beavoided.9. Precision and Bias9.1 No statement is made about either precision or bias forPractice D3452 since this practice is intended primarily for theidentification of polymers and their relative ratios and not theabsolute levels

41、of the polymers in the compounds beingstudied.PART 2. IDENTIFICATION OF BLENDS OF POLYMERS10. Scope10.1 This practice is a guide to the identification of blendsof rubbers in the raw, vulcanized, and unvulcanized state by thegas chromatographic patterns of pyrolysis products (pyro-grams). Implementat

42、ion of this guide presupposes a workingknowledge of the principles and techniques of gaschromatography, sufficient to carry out the practice, as written,and to interpret the results correctly.10.2 Two methods are described, depending upon the natureof the blend.10.2.1 Method AThis method is used whe

43、n styrene-butadiene copolymers are absent. The absence of the styrenepeak, in a preliminary pyrogram, indicates this type of blend.Method A will identify blends of the following:10.2.1.1 Polyisoprene of natural or synthetic origin,10.2.1.2 Butadiene,10.2.1.3 Isobutene-isoprene copolymers, and10.2.1.

44、4 Halogenated isobutene-isoprene rubbers.10.2.2 Method BThis method is used when butadiene-styrene copolymers are present. The presence of the styrenepeak, in a preliminary pyrogram, indicates this type of blend.The method fails if other styrene polymers or copolymers orunextractable styrene-contain

45、ing resins are present. Method Bis particularly suitable for the identification of polybutadiene inblends with styrene-butadiene copolymers. If the presence ofpolybutadiene in the unknown rubber can be excluded, useMethod A. Method B will identify butadiene-styrene copoly-mers with blends of the fol

46、lowing:10.2.2.1 Polyisoprene of natural or synthetic origin,10.2.2.2 Butadiene, and10.2.2.3 Isobutene-isoprene copolymers and halogenatedisobutene-isoprene rubbers.10.3 Methods A and B will not differentiate the following inblends:10.3.1 Natural polyisoprene from synthetic polyisoprene,10.3.2 Polybu

47、tadiene containing different microstruc-tures,10.3.3 Isobutene-isoprene copolymers and their related ha-logenated rubbers, and10.3.4 Styrene-butadiene copolymers with different mono-mer ratios or different microstructures.11. Referenced Document11.1 See Section 2.12. Significance and Use12.1 See Sec

48、tion 3.13. Principle of the Practice13.1 See Section 4 in addition to the following:13.1.1 Method AThis method is based upon the identifi-cation of the characteristic hydrocarbon in the pyrogram of theunknown rubber. The identification of the characteristic hydro-carbon is achieved by comparison of

49、retention times under thesame chromatographic conditions for a known rubber as for anunknown rubber. These retention times can be obtained frompyrograms of known rubbers or by direct injection of the purehydrocarbon into the chromatograph.13.1.2 Method BThis method is based upon the identifi-cation of the peaks of vinylcyclohexene and styrene and theirretention times, as in Method A. Identification of the butadienepeaks is useful but not strictly necessary.D3452 06 (2017)313.2 The success of Method A or B depends upon examin-ing the unknown rubber

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1