ASTM D3566-2003(2009) Standard Practice for Rubber&8212 Determination of Bromine in the Presence of Chlorine by Oxygen Combustion《用氧燃烧法测定在氯存在时橡胶中的溴含量的标准实施规程》.pdf

1、Designation: D 3566 03 (Reapproved 2009)Standard Practice forRubberDetermination of Bromine in the Presence ofChlorine by Oxygen Combustion1This standard is issued under the fixed designation D 3566; the number immediately following the designation indicates the year oforiginal adoption or, in the c

2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the determination of bromine andchlorine in rubber.1.2 This procedur

3、e is applicable to raw or cured NR, SBR,BR, IR, IIR, CIIR, BIIR, and EPDM rubbers and blends ofthese.1.3 Iodine interferes, but substances such as Zn2+,S,CN,and (CO3)2do not.1.4 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.

4、5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. Specific safetyp

5、recautions are given in Section 7.2. Referenced Documents2.1 ASTM Standards:2E 200 Practice for Preparation, Standardization, and Stor-age of Standard and Reagent Solutions for ChemicalAnalysisE 443 Test Method for Sulphur in Organic Compounds byOxygen Flask Combustion33. Summary of Practice3.1 Samp

6、les of rubber, wrapped in filter paper, are burned inan oxygen combustion flask containing an aqueous solution ofhydrogen peroxide and sodium bisulfite. The carbon andhydrogen of the organic matter are oxidized. The combustedsolution is titrated directly for bromine and chlorine.4. Significance and

7、Use4.1 This practice outlines a method for the determination ofbromine and chlorine, alone or together.4.2 CIIR and BIIR rubbers contain small amounts of chlo-rine and bromine and CR rubbers contain large amounts ofchlorine. For quality control and research and development, itis sometimes necessary

8、to determine the amount of thesehalogens in rubber. This practice can be used for thesepurposes.5. Apparatus5.1 Oxygen Combustion Flask (Schniger Flask)Achemical-resistant,4thick-walled oxygen combustion flask,51000 cm3, with JS35/25 ball-joint stopper, platinum samplecarrier, and pinch clamp.5.2 In

9、frared Safety Igniter,5,6with cabinet and infrared light(an electrical igniter is also satisfactory).5.3 Magnetic Stirring Bar, covered with a chemical-resistant coating,5,7approximately 25 mm (1 in.) long, withouta spinning ring around the center.5.4 Magnetic Stirrer.1This practice is under the jur

10、isdiction ofASTM Committee D11 on Rubber andis the direct responsibility of Subcommittee D11.11 on Chemical Analysis.Current edition approved Jan. 1, 2009. Published March 2009. Originallyapproved in 1977. Last previous edition approved in 2003 as D 3566 03.2For referenced ASTM standards, visit the

11、ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.4Borosil

12、icate glass has been found satisfactory.5The sole source of supply of the apparatus known to the committee at this timeis A. H. Thomas Co., Philadelphia, PA, Catalog No. 6514-F20. If you are aware ofalternative suppliers, please provide this information to ASTM InternationalHeadquarters. Your commen

13、ts will receive careful consideration at a meeting of theresponsible technical committee,1which you may attend.6The sole source of supply of the apparatus known to the committee at this timeis A. H. Thomas Co., Philadelphia, PA, Catalog No. 6516-G10.7Polytetrafluoroethylene has been found satisfacto

14、ry.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.5 Filter Paper, 30 by 30 mm, with a 35-mm extension,black5,8for infrared or white5,9for electrical ignition.5.6 pH Meter,10equipped with a billet-type silver elec-trode11and a calo

15、mel electrode, in which the potassiumchloride solution has been replaced by a saturated potassiumnitrate solution, or equivalent automatic titrator.6. Reagents6.1 Silver Nitrate Solution (0.001 M) must be freshly pre-pared. Pipet 10.0 cm3of standard120.1 M silver nitrate solutioninto a 1-dm3volumetr

16、ic flask. Dilute to volume. Protect fromlight. Determine its molarity by titrating an accurately weighedsample of the reagent grade KCl or NaCl. Calculate themolarity as follows:Molarity 5 A 3 1000/B 3 C! (1)where:A = grams of chloride weighed,B = molecular mass of chloride used, andC = titration vo

17、lume, cm3.6.2 Sodium Bisulfite, 35 % in water,6.3 Hydrogen Peroxide, 3 % solution,6.4 Nitric Acid (6M).6.5 Aluminum Nitrate,6.6 Isopropyl Alcohol,6.7 Methyl Orange Indicator (1 % solution in methyl alco-hol), and6.8 Oxygen in Compressed Gas Cylinder.7. Safety Precautions7.1 The following safety prec

18、autions must be observed inthe combustion of rubber samples:7.1.1 The flask shall not contain residues of organic solventsor vapor, which could cause an explosion. Any such solventsused for cleaning the flask should be rinsed out repeatedly withwater.7.1.2 The pressure generated by the rapid combust

19、ion couldcause the flask to explode. Therefore, combustion shall takeplace in a safety chamber with the door locked or behind asafety shield or hood shield (preferably in a safety chamber thatis behind a shield); the hands and face shall be withdrawnbehind a screen before the flame reaches the sampl

20、e itself.Goggles or a face shield should be worn while observing thecombustion procedure.7.1.3 The flask should be left in the safety chamber until thelast spark is extinguished.At this point it is removed; but sincea slight vacuum is formed, goggles or a face shield should stillbe worn.8. Sampling8

21、.1 The representative test portion selected for analysismust be milled or cut into very fine pieces before weighing.8.2 Due to the small sample size, the rubber and filter papershould be protected from contamination, and all operationsprior to combustion should be carried out while wearing plasticgl

22、oves.9. Procedure9.1 Place 10 cm3of water, five drops hydrogen peroxide,and2cm3of sodium bisulfite solution into the combustionflask.9.2 Fold the filter paper into a U-shaped sample boat.9.3 Weigh a sample of 80 to 100 mg (which should notexceed approximately 0.25 milliequivalents of bromine) to the

23、nearest 0.1 mg. Place the sample into the folded filter paperboat.9.4 Place the folded paper firmly in the platinum samplecarrier hung on the hook of the stopper, with the pointed end ofthe paper projecting outward.9.5 Insert a tube from the oxygen cylinder close to thebottom of the flask and admit

24、oxygen rapidly for 5 min.9.6 Carefully remove the oxygen tube and stopper the flask.9.7 With the stopper upright, clamp the stopper tightly withthe pinch clamp.9.8 Place the flask in the infrared igniter chamber with thepointed end of the paper in line with the infrared beam andapproximately perpend

25、icular to it. Close the door and turn onthe infrared light (or electric igniter) until the paper ignites.9.9 After combustion is complete, moisten the stopperexternally with a few drops of water to avoid loss of halogen.Let sit 1 min. Shake the flask. Allow to rest for 30 min.9.10 Remove the pinch c

26、lamp, tilt the stopper to release thevacuum, and open the flask.9.11 Where the bromine and chlorine content, or both, islow, repeat the procedure of 9.1 to 9.10, burning anothersample of about the same size over the same liquid.9.12 Open the flask; wash sides, stopper, and carrier withwater.9.13 Add

27、 3.5 cm3of HNO3solution. Close flask and shaketo dissolve ash in basket.9.14 Pour solution into 400 cm3beaker containing a mag-netic stirrer.9.15 Wash the flask with isopropyl alcohol, adding wash-ings to beaker. The final composition should be close to 80 %alcohol, 20 % water.9.16 Add 4 g aluminum

28、nitrate and two drops methylorange. Solution should turn red. If not, add HNO3until redcolor appears.9.17 Titrate the solution with 0.001 M AgNO3(6.1), usingthe pH meter arrangement described (5.6) or an equivalentautomatic titrator. Add titrant in increments of 0.01 cm3.9.18 The first inflection po

29、int on the curve of millivoltsversus cubic centimetres of titrant, represents bromide; thesecond inflection point represents chloride. The end point is thepoint of maximum change in emf for an increment of titrant.8The sole source of supply of the apparatus known to the committee at this timeis A. H

30、. Thomas Co., Philadelphia, PA, Catalog No. 6514-F65.9The sole source of supply of the apparatus known to the committee at this timeis A. H. Thomas Co., Philadelphia, PA, Catalog No. 6513-C75.10A. Beckman pH meter Model SS-2 has been found satisfactory.11Coleman Catalog No. 3-571 has been found sati

31、sfactory.Any equivalent silverelectrode may be used. The electrode should not be coated by the user, especially forTest Method B. It may, however, be polished with a mild abrasive such as powderedkitchen cleanser, so that it is bright and shiny.12The 0.1 M silver nitrate solution should be prepared

32、in accordance withPractice E 200 or may be purchased.D 3566 03 (2009)29.19 For a better end point, a known amount of bromide andchloride may be added to the sample solution before titration.Deduct this amount from the total titration.9.20 Carry a blank throughout the entire procedure, usingthe same

33、quantity of reagents, but omitting the sample.10. Calculation10.1 Calculate the bromine content as follows:Bromine, % 5 B 2 A! 3 M 3 7.99/W (2)where:B = volume ofAgNO3solution required for titration to thefirst inflection point, cm3,A = volume ofAgNO3solution required for titration of theblank,M = m

34、olarity of the AgNO3solution, andW = mass of rubber samples burned in the flask, g.10.2 Calculate the chlorine content as follows:Chlorine, % 5 C 2 B! 3 M 3 3.55/W (3)where:C = volume ofAgNO3solution required for titration to thesecond inflection point, cm3,B = volume ofAgNO3solution required for ti

35、tration to thefirst inflection point, cm3,M = molarity of the AgNO3solution, andW = mass of rubber samples burned in the flask, g.11. Report11.1 Report the following information:11.1.1 Sample identification, and11.1.2 Test result, which is the average of two determina-tions.12. Precision and Bias12.

36、1 This practice has not been tested in a round-robin testprogram.13. Keywords13.1 bromine; chlorine; oxygen combustionASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly

37、 advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, ei

38、ther reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may atten

39、d. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 3566 03 (2009)3