1、Designation: D3678 97 (Reapproved 2008)1D3678 14 An American National StandardStandard Specification forRigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions1This standard is issued under the fixed designation D3678; the number immediately following the designation indicates the year oforigin
2、al adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1 NOTEEditorial changes were made throughout in April 2008.1. Scope*1.1 This
3、specification establishes requirements for the material properties, including dimensional stability and extrusion quality,of rigid, poly(vinyl chloride) (PVC) interior-profile extrusions. Methods for identifying interior-profile extrusions that comply withthe requirements of this specification are p
4、rovided.1.2 Rigid Use of rigid PVC recycled plastic may be used in this product in is permitted in accordance with the requirementsinof Sections 6 and 7.1.3 Rigid PVC compounds for interior building product applications are covered in Specification D1784.1.4 Rigid PVC exterior profile extrusions for
5、 assembled windows and doors are covered in Specification D4726.1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes(excluding those in Tables and Figures) shall not be considered as requirements of this standard.1.6 The values st
6、ated in SI units are to be regarded as the standard. The values given in parentheses are given for informationonly.NOTE 1Information with regard to application should be obtained from the manufacturers of the profiles.NOTE 2There is no know ISO equivalent to this standard.NOTE 1Information with rega
7、rd to application should be obtained from the manufacturers of the profiles.NOTE 2There is no known ISO equivalent to this standard.1.7 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification:This standarddoes not purport to address all of the sa
8、fety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning P
9、lastics for TestingD696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous SilicaDilatometerD883 Terminology Relating to PlasticsD1042 Test Method for Linear Dimensional Changes of Plastics Caused by Exposure to Heat and MoistureD1600 Terminology
10、for Abbreviated Terms Relating to PlasticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC)CompoundsD2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by AcetoneImmersionD3892 Practice
11、for Packaging/Packing of PlasticsD4726 Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used forAssembled Windows and DoorsD4968 Guide for Annual Review of Test Methods and Specifications for Plastics1 This specification is under the jurisdiction of ASTM Committee D20 o
12、n Plastics and is the direct responsibility of Subcommittee D20.24 on Plastic Building Products.Current edition approved March 1, 2008Aug. 1, 2014. Published April 2008August 2014. Originally approved in 1978. Last previous edition approved in 20012008 asD3678 97 (2008)1(2001) DOI: 10.1520/D3678-97R
13、08E01.10.1520/D3678-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard
14、and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases onl
15、y the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1D7209 Guide for Waste
16、 Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and ProductsE631 Terminology of Building Constructions3. Terminology3.1 GeneralDefintions are in accordance with Terminology D883 or Terminology E631 and abbreviations with TerminologyD1600, unless otherwise indicated.4. Signific
17、ance and Use4.1 The purpose of this specification is to establish on a national basis, a recognized standard of quality for rigid poly(vinylchloride) (PVC) interior-profile extrusions for interior use other than cellular products, piping, tubing, and window and doorprofiles used in finished building
18、 products. The information contained in this standard is intended to be helpful to producers,distributors, and users, and to promote understanding between buyers and sellers. It is also intended to serve as the basis forrequirements on finished interior building products which are either made from o
19、r employ rigid PVC profile extrusions in theirconstruction.5. Classification5.1 This standard covers three classes of rigid PVC interior-profile extrusions as follows:Class 1Normal impactClass 2Intermediate impactClass 3High impact6. Materials and Manufacture6.1 This specification covers profile ext
20、rusions made from plastics conforming to the requirements of Specification D1784.Class 1 extrusions shall meet the requirements specified in Specification D1784 for Class 12454 compound. Class 2 extrusionsshall meet the requirements for Class 14323 compound. Class 3 extrusions shall meet the require
21、ments for Class 1-40031-54-0000compound. Refer to Table 1 in Specification D1784.6.2 Rigid Use of rigid PVC recycled plastic, as defined in Guide D7209, may be used is permitted in this product if all therequirements in the sections on Materials and Manufacture (Section 6), and on Physical Requireme
22、nts (Section 7) are met by theextrusions containing PVC recycled plastic.6.3 All Class compounds shall have a minimum coefficient of linear expansion of 10 10-5 cmcm cm/cm/C C (5.5 10-5in./in./F). in.in.F).NOTE 3Non-PVC materials may be used as a capstock.6.4 Rework MaterialClean, homogeneous PVC re
23、work material or rework material containing PVC capstock generated fromthe manufacturers own production of the same class compound may be used is permitted for use by the same manufacturerprovidingprovided that the extruded profiles meet all the requirements of this specification. Clean principally
24、PVC rework materialcontaining non-PVC capstock may be used is permitted for use only in the substrate of a capstocked product by the samemanufacturer, providing that the extruded profiles meet all of the requirements of this specification.6.5 The PVC compound in extruded section shall maintain unifo
25、rm color and be free of any visual surface or structural changes,such as peeling, chipping, cracking, flaking, or pitting.7. Physical Requirements7.1 DimensionsThe size, thickness, and dimensional tolerances of the interior-profile extrusions shall be as agreed uponbetween the supplier and purchaser
26、.7.2 Dimensional StabilityThe dimensional stability of the interior-profile extrusions shall be determined in the extrusiondirection in accordance with 8.5. Extrusions over 1.02 mm (0.040 in.) in thickness shall have a maximum shrinkage of 2.2 %; thoseof 1.02-mm (0.040-in.) thickness or less shall h
27、ave a 3.0 % maximum shrinkage.7.3 Extrusion QualityThe extrusion quality of Class 1 extrusions shall be determined by immersion in anhydrous acetone inaccordance with the requirements of 8.6. Specimens of extrusions having not more than 25 % surface attack shall be consideredas adequately fused and
28、of satisfactory quality. The extrusion qualities of Class 2 and Class 3 extrusions shall be as agreed uponbetween the supplier and purchaser.8. Test Methods8.1 GeneralUse the inspection and test procedures contained in this section to determine the conformance of products to therequirements of this
29、specification. Each producer or distributor who represents his products as conforming to this specification mayutilize statistically based sampling plans that are appropriate for each particular manufacturing process, but shall keep suchD3678 142essential records as are necessary to document with a
30、high degree of assurance his claim that all of the requirements of thisspecification have been met. Additional sampling and testing of the product, as may be agreed upon between supplier andpurchaser, is not precluded by this section.8.2 Visual InspectionVisually examine the interior-profile extrusi
31、ons to determine their compliance with the requirements of6.5.8.3 Conditioning of SpecimensCondition the test specimens in accordance with ProcedureAof Practice D618, except that theminimum conditioning time shall be 24 h.8.4 Test ConditionsConduct the tests the Standard Laboratory Atmosphere of 23
32、6 1C (73.4 6 1.8F) and 50 6 5 %10 %relative humidity, unless otherwise specified in the applicable test method.8.5 Dimensional StabilityDetermine the dimensional stability in accordance with Test Method D1042, except that the testcycle shall consist of heating the specimens for 30 min in a uniformly
33、 heated oven at a temperature of 82.0 6 0.6C (180 6 1F).6 1F).8.6 Extrusion QualityDetermine the extrusion quality in accordance with Test Method D2152, except that the test specimensshall be 25.40 to 50.80 mm (1 to 2 in.) in length and sufficient in number to ensure testing the complete cross secti
34、on. In the testprocedure described, the interior-profile extrusions will normally swell and soften in contact with anhydrous acetone. In some casesthere may be surface attack. Disintegration is defined as complete separation of flakes or pieces from the body of the extrusion.8.7 Coeffcient of Linear
35、 ExpansionConduct this test in accordance with Test Method D696.9. Product Marking9.1 In order that purchasers may identify To aid identification of products conforming to all requirements of this specification,producers and distributors mayshall include a statement of compliance in conjunction with
36、 their name and address on productlabels, invoices, sales literature, and the like. The following statement is suggested when sufficient space is available:“The product conforms to all of the requirements established in ASTM D3678, developed cooperatively with the industry andpublished by ASTM.”“Ful
37、l responsibility for the conformance of this product to this specification is assumed by (name and address of producer ordistributor).”9.2 The following abbreviated statement is suggested when available space on labels is insufficient for the full statement:“Conforms to ASTM D3678 (name and address
38、of producer or distributors).”9.3 All packing, packaging, and marking provisions of Practice D3892 shall apply to this specification.10. Packaging10.1 The interior-profile extrusions shall be packaged in such a manner as to provide reasonable protection against damage inordinary handling and transpo
39、rtation.11. Keywords11.1 building products; extrusion; interior profile extrusions; recycled plastic; rigid poly(vinyl chloride)SUMMARY OF CHANGESCommittee D20 has identified the location of selected changes to this standard since the last issue(D367897(2001)D3678 97 (2008)1) that may impact the use
40、 of this standard.(1) Reworded ISO equivalency statement per Guide D4968.(1) DeletedRevised D5033 reference in Sectionhumidity requirements from 65 % to 610 % to bring in line 2 and added Guidewith Practice D7209D618.(3) Deleted D5033 reference in Section 6 and added Guide D7209.(4) Adjusted signifi
41、cant digits in 8.4 and 8.5.D3678 143ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the ris
42、kof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this
43、 standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake y
44、our views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by c
45、ontacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 144
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1