ASTM D3693-2002 Standard Specification for Labeled Length per Holder of Sewing Thread《标签标明的缝纫线每团长度的标准规范》.pdf

1、Designation: D 3693 02Standard Specification forLabeled Length per Holder of Sewing Thread1This standard is issued under the fixed designation D 3693; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num

2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements for the labeledlengths of sewing threads of all materials.2. Referenced Documents2.1 ASTM Standard

3、s:2D 123 Terminology Relating to TextilesD 204 Methods of Testing Sewing ThreadsD 3888 Terminology Related to Open-End SpinningD 3990 Terminology Relating to Fabric DefectsD 4849 Terminology Relating to Fibers and Yarns3. Terminology3.1 Definitions:3.1.1 For definitions of textile terms used in this

4、 specifica-tion, thread holder and sewing thread, refer to TerminologyD 4849.3.1.2 For other textile terms used in this specification, referto Terminology standards D 123, D 3888, D 3990, AndD 4849.4. Requirements4.1 The average for all holders shall equal or exceed thelabeled length.4.2 For home se

5、wing spools, the observed length of indi-vidual holders shall equal or exceed the percent of labeledlength shown in Table 1.4.3 For ready-made bobbins, the observed length of indi-vidual holders shall equal or exceed 97 % of the labeled length.4.4 For all other holders, when the sample size is nine

6、orfewer, the observed length of individual holders shall equal orexceed 95 % of the labeled length. For a sample size of ten ormore the observed length of one holder may be less than 95 %of the labeled length.4.5 If the initial sample consists of fewer than ten holdersand the average length measured

7、 fails to conform to therequirements of 4.1 but meets those of 4.2, 4.3, or 4.4, asappropriate, take additional specimens from the lot and testuntil a total of ten have been measured. Reevaluate the resultsof these ten specimens against the requirements of 4.1, 4.2, 4.3,or 4.4, as appropriate. If th

8、e new average conforms with therequirements of 4.1 and the individual holders with therequirements of 4.2, 4.3, or 4.4, as appropriate, consider the lotacceptable.4.5.1 If the original lot consists of fewer than ten holders,the supplementary sample will be one half of the holdersremaining in the lot

9、 following the initial sampling.5. Sampling5.1 LotUnless otherwise agreed upon between the pur-chaser and supplier, a lot shall be a discrete manufacturing unitor a billed quantity of a specific color, ticket size, and lengthput-up of thread. A billed quantity can consist of a single unit,a carton,

10、box, or multiple units of either, containing a numberof holders of thread.NOTE 1An adequate specification or other agreement between thepurchaser and the supplier requires taking into account variability betweenshipping units, between packages, or ends within shipping unit, andbetween specimens from

11、 a single package so as to provide a sampling planwith a meaningful producers risk, users risk, acceptable quality level,and limiting quality level.5.2 SampleUnless otherwise agreed upon between thepurchaser and supplier, and except for ready-made bobbins, thesample, chosen at random, shall be 10 %

12、of the holders in thelot, with a minimum of one holder, up to a maximum of tenholders. The lot sample and laboratory sample are synony-mous.5.2.1 For ready-made bobbins the sample shall be as shownin Table 2.1This specification is under the jurisdiction of ASTM Committee D13 onTextiles and is the di

13、rect responsibility of Subcommittee D13.58 on Yarn TestMethods, General.Current edition approved Sept. 10, 2002. Published November 2002. Originallypublished as D 3693 78. Last previous edition D 3693 91 (Reapproved 1996)e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcont

14、act ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.TABLE 1 Minimum Length for Individual Home Sewing SpoolsLabeled Length, m Minimum % Allowed0 to 40 98.5Over 40 to 85 98Over 85 to 140 97.

15、5Over 140 to 300 97Over 300 to 1000 96Over 1000 951Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.3 SpecimenThe test specimen is a holder of threadwhether a cone, tube, spool, ready-made bobbin, or other.6. Test Method6.1 Determine

16、 the length of each holder of thread asdirected in the length per thread holder procedure of TestMethod D 204. Use the sampling directions in this specifica-tion in place of those in Methods D 204.7. Conformance7.1 Material that fails to conform to the requirements of thisspecification may be reject

17、ed. Rejection shall be reported to thesupplier promptly and in writing. In case of dissatisfaction withthe results of the test, the supplier may make claim for arehearing. The terms of the rehearing shall be as agreed uponbetween the supplier and the purchaser.8. Keywords8.1 length; sewing threadAST

18、M International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are en

19、tirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsa

20、nd should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee

21、on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 2 Sampling Plan for Ready-Made BobbinsLot Size, gross Sample Size10 or less 10 bobbins11 through 99 1 bobbin per gross100 or more 100 bobbinsD3693022