ASTM D3737-2012 Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)《确定结构级胶合叠层木材的允许特性的标准实施规程》.pdf

1、Designation: D3737 091 D3737 12Standard Practice forEstablishing Allowable Properties for Structural GluedLaminated Timber (Glulam)1This standard is issued under the fixed designation D3737; the number immediately following the designation indicates the year oforiginal adoption or, in the case of re

2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1 NOTEAppendix X2 was editorially changed in April 2012.1. Scope1.1 This practice covers the procedures for es

3、tablishing allowable properties for structural glued laminated timber. Included arethe allowable stresses for bending, tension and compression parallel to the grain, horizontal shear, compression perpendicular tothe grain, and radial tension and compression in curved members. Also included are modul

4、us of elasticity and modulus of rigidity.1.2 This practice is limited to the calculation of allowable properties subject to the given procedures for the selection andarrangement of grades of lumber of the species considered.1.3 Requirements for production, inspection and certification are not includ

5、ed, but in order to justify the allowable propertiesdeveloped using procedures in this practice, manufacturers must conform to recognized manufacturing standards. Refer toANSI/AITC A190.1 and CSA O122.1.4 The values stated in inch-pound units are to be regarded as standard. The values given in paren

6、theses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropria

7、te safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D9 Terminology Relating to Wood and Wood-Based ProductsD143 Test Methods for Small Clear Specimens of TimberD198 Test Methods of Static Tests of Lumber in S

8、tructural SizesD245 Practice for Establishing Structural Grades and Related Allowable Properties for Visually Graded LumberD2395 Test Methods for Specific Gravity of Wood and Wood-Based MaterialsD2555 Practice for Establishing Clear Wood Strength ValuesD2915 Practice for Sampling and Data-Analysis f

9、or Structural Wood and Wood-Based ProductsD4761 Test Methods for Mechanical Properties of Lumber and Wood-Base Structural MaterialD5456 Specification for Evaluation of Structural Composite Lumber ProductsD6570 Practice for Assigning Allowable Properties for Mechanically Graded LumberE105 Practice fo

10、r Probability Sampling of Materials2.2 AITC Standards:3AITC 117-71 Standard Specifications for Structural Glued Laminated Timber of Softwood Species, 1971AITC 117-74 Standard Specifications for Structural Glued Laminated Timber of Softwood Species, 1974AITC 117-79 Standard Specifications for Structu

11、ral Glued Laminated Timber of Softwood Species, 1979AITC “Brown Book” Determination of Design Values for Structural Glued Laminated, 19791 This practice is under the jurisdiction of ASTM Committee D07 on Wood and is the direct responsibility of Subcommittee D07.02 on Lumber and Engineered WoodProduc

12、ts.Current edition approved Sept. 1, 2009Nov. 1, 2012. Published December 2009December 2012. Originally approved in 1978. Last previous edition approved in 20082009as D3737 08.D3737 09E01. DOI: 10.1520/D3737-09E01.10.1520/D3737-12.2 For referenced ASTM standards, visit the ASTM website, www.astm.org

13、, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from the American Institute of Timber Construction, 7012 S. Revere Parkway, Suite 140, Centennial, CO 80112, https:

14、/www.aitc-glulam.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that us

15、ers consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1AITC Standard 407 Standard

16、for Alternate Lumber Grades for Use in Structural Glued Laminated Timber, 2005AITC Standard 500 Determination of Design Values for Structural Glued Laminated Timber in Accordance with ASTMD3737-89a, 1991AITC Technical Note 21 Volume Factor for Structural Glued Laminated Timber, 2005ANSI/AITC A190.1

17、Structural Glued Laminated Timber, 20072.3 Other Standards:ANSI/AF or solid-sawn lumber that is produced accordingto Practice D6570 and the grading rules of the applicable grading or inspection agency.3.1.2 E-rated lumberlumber graded for use in manufacturing structural glued laminated timber by non

18、destructivemeasurement of a modulus of elasticity (E) and by visual inspection in accordance with the grading rules of the applicable gradingor inspection agency.3.1.3 glulama term used to denote structural glued laminated timber, which is a product made from suitably selected andprepared pieces of

19、wood bonded together with an adhesive either in a straight or curved form with the grain of all pieces essentiallyparallel to the longitudinal axis of the member.3.1.4 horizontally laminated timbera member designed to resist bending loads applied perpendicularly to the wide faces ofthe laminations (

20、referred to as bending about the x-x axis).3.1.5 laminationa layer of lumber within the glued laminated timber.3.1.6 modulus of elasticity (E)for laminating, E is designated in two categories to distinguish mode of measurement andapplication.3.1.6.1 Long-Span E (LSE)the modulus of elasticity calcula

21、ted from deflection measured in a flat-wise static bending test oflumber with a center point loading and a span-to-depth ratio (1d) of approximately 100 or the E obtained from Test Methods D2555and multiplying by the appropriate factors from Table 1 and Table 6.3.1.6.2 Member E (Eaxial , Ex, Ey)the

22、allowable modulus of elasticity values of the structural glued laminated member asdefined in this practice.3.1.7 vertically laminated timbera member designed to resist bending loads applied parallel to the wide faces of thelaminations (referred to as bending about the y-y axis).3.1.8 visually graded

23、 lumberlumber graded by visual inspection in accordance with the grading rules of the applicable gradingor inspection agency.3.1.9 GDCthe ratio of the cross-sectional area of the local grain deviation (which may or may not be associated with a knot)away from the edge of the lumber to the cross secti

24、onal area of the lumber (see Fig. 1).3.1.10 GDEthe ratio of the cross-sectional area of the local grain deviation (which may or may not be associated with a knot)at the edge of the lumber to the cross sectional area of the lumber (see Fig. 1).3.1.11 GDSthe projected sum of all GDE and GDC values wit

25、hin a one-foot length of lumber as defined in Fig. 1.4 Available from American Forest and Paper Association (AF grain deviations (with or without knots) are measured to the lateral extremes of thezone within which the local slope of grain exceeds the allowable slope of grain for the grade. Eq 8-11 w

26、hich follow yield themaximum allowable knot and grain deviation ratios in the outer 10 % of depth. It is suggested these ratios be adjusted downwardto the nearest 0.05 or to the next nearest convenient fraction (such as 13).4.3.2.3 Beams Greater than 15 in. (0.38 m) in Depth:(1) Outer 5 %Grain devia

27、tion shall be limited in accordance with Eq 1 and 2.GDS#1.5512SRtl! (1)GDS#1.8212SRtl! (2)(a) (b)GDC = y/b GDC = y/bGDE = z/b GDE = z/bGDS = x/b where x = y + z GDS = x/b where x 15 in.A4.1.12 The required strength ratio of the tension lamination (SRTL) shall be calculated using Eq A4.15, and the te

28、nsion laminationgrading requirements of 4.3 shall be determined, if a tension lamination factor of 1.0 is used in Equation Eq A4.14.SRTL 5FbxS 2dTLD DS ETLETDS IgITDBSITL (A4.15)where:dTL = distance from neutral axis to outer edge of tension lamination,ETL = long-span modulus of elasticity of the lu

29、mber in the outermost tension zone, andBSITL = bending stress index of the lumber in the outermost tension zone.A4.2 ExampleGiven the 20-lamination beam shown in Fig. A4.1 and the lumber grade data in Table A4.1, determine theallowable bending stress and tension lamination grading requirements for f

30、lexure with compression at the top of the section.A4.2.1 The neutral axis is located relative to the bottom of the beam using Eq A4.1. For convenience, distances are measured innumber of laminations.y 5S2.12 D22!1S1.82 D72222!1S1.12 D152272!1S1.82 D1922152!1S2.12 D2022192!2.12!11.8722!11.11527!11.81

31、9215!12.120219!y 59.740 laminations from the bottomA4.2.1.1 The core zone is split by the neutral axis into two zones for the analysis and the zones are numbered from the bottomof the beam. The distance from the neutral axis to the edges of each zone (Fig. A4.1) are determined using Eq A4.2 and A4.3

32、.FIG. A4.1 Example of a 20-Lamination BeamD3737 1219N05s029.740d529.740N15s229.740d527.740N25s729.740d522.740N35s9.74029.740d50N45s1529.740d55.260N55s1929.740d59.260N65s2029.740d510.260A4.2.1.2 Negative results indicate that the zone boundaries represented by N0, N1, and N2 are below the neutral axi

33、s. Positiveresults indicate that the zone boundaries represented by N4, N5, and N6 are above the neutral axis.A4.2.2 The transformed moment of inertia for each zone about the neutral axis is calculated using Eq A4.4. For convenience, thewidth of the untransformed section, b, will be set equal to uni

34、ty.I65S2.12.1Ds10.26329.2603d3 595.34I55S1.82.1Ds9.260325.2603d3 5185.3I45S1.12.1Ds5.2603203d3 525.41I35S1.12.1Ds032s22.740d3d3 53.592I25S1.82.1Dss22.740d32s27.740d3d3 5126.6I15S2.12.1Dss27.740d32s29.740d3d3 5153.4A4.2.2.1 The moment of inertia of the transformed section is calculated using Eq A4.5.

35、IT 5I11I21I31I41I51I65153.41126.613.592125.411185.3195.345589.6A4.2.3 The moment of inertia of the untransformed (gross) section is calculated using Eq A4.6.Ig 5 20312 5666.7A4.2.4 Weighting factors, Oj and Pj are calculated for each zone using Eq A4.7 and A4.8.O65210.26329.2603!5572.0P65 25910.26!5

36、2510.26!3110.26!299.260!5159.260!329.260!5163.6103!O5529.260325.2603!51297P55 2599.260!5259.260!319.260!295.260!5155.260!325.260!5229.3103!O4525.2603203!5291.1P45 2595.260!5255.260!315.260!290!5150!320!514.21103!O35203222.740!3!541.14TABLE A4.1 Lumber Data for Analysis of Glulam Beam Bending Stress

37、(see Ref (12)Grade and SpeciesA Modulus of ElasticityB Bending Stress IndexC Knot DataDSRbx minEx 99.5 Percentile hpsi MPa psi MPa % % %L1 Douglas fir 2 100 000 14 500 3500 24.1 6.9 42.2 35.3 0.75L2 Douglas fir 1 800 000 12 400 3000 20.7 10.9 54.9 44.0 0.67L3 Lodgepole pine 1 100 000 7 600 1933 13.3

38、 23.0 78.8 55.8 0.5A Graded in accordance with WWPA and WCLIB rules under the American Lumber Standard (5 and 6). L3 lodgepole pine graded under rules for L3 Douglas fir.B Based on 6.1.4 for Douglas fir and 6.1.4 and 7.5 for lodgepole pine.C Based on 6.1.1.1 for Douglas fir and 6.1.1 for lodgepole p

39、ine.D Based on knot surveys and analysis in accordance with Annex A3 and Annex A6.E As determined by formula X1.2 of Practice D245, in accordance with 7.2.1.1 (1).D3737 1220P35 2590!5250!310!2922.740!51522.740!3222.740!5515.9O25222.740!3227.740!3!5443.1P25 25922.740!52522.740!3122.740!2927.740!51527

40、.740!3227.740!598.56103!O15227.740!3229.740!3!5920.7P15 25927.740!52527.740!3127.740!2929.740!51529.740!3229.740!5214.6103!A4.2.5 An Ik/Ig ratio is calculated for each zone using Eq A4.9.SIkIgD650.069!S2.12.1D572.0!10.109!S1.82.1D1297!10.230!S1.12.1D291.1!210.26!31!0.353!2S2.12.1D2163.3103!10.440!2S

41、1.82.1D2229.3103!10.558!2S1.12.1D214.21103!210.26!3SIkIgD650.198SIkIgD550.109!S1.81.8D1297!10.230!S1.11.8D291.1!29.260!310.440!2S1.81.8D2229.3103!10.558!2S1.11.8D214.21103!29.260!3SIkIgD550.2499SIkIgD450.230!S1.11.1D291.1!10.558!2S1.11.1D214.21103!25.260!3SIkIgD450.4585SIkIgD350.230!S1.11.1D41.14!10

42、.558!2S1.11.1D2515.9!22.740!3SIkIgD350.5381SIkIgD250.109!S1.81.8D443.1!10.230!S1.11.8D41.14!27.740!310.440!2S1.81.8D298.56103!10.558!2S1.11.8D2515.9!27.740!3SIkIgD250.2075SIkIgD15D3737 12210.069!S2.12.1D920.7!10.109!S1.82.1D443.1!10.230!S1.12.1D41.14!29.740!31!0.353!2S2.12.1D2214.6103!10.440!2S1.82.

43、1D298.56103!10.558!2S1.12.1D2515.9!29.740!3SIkIgD150.1688A4.2.6 The stress modification factor for knots is calculated for each zone using Eq A4.10, subject to the minimum strength ratiofrom 7.2.1.1 (1) (Table A4.1).SMFbx knots 65s113s0.1980dds12s0.1980dd3S12S0.19802 DD$0.75SMFbx knots 650.741$0.75S

44、MFbx knots 650.75SMFbx knots 55s113s0.2499dds12s0.2499dd3S12S0.24992 DD$0.67SMFbx knots 550.646$0.67SMFbx knots 550.67SMFbx knots 45s113s0.4585dds12s0.4585dd3S12S0.45852 DD$0.50SMFbx knots 450.291$0.50SMFbx knots 450.50SMFbx knots 35s113s0.5381dds12s0.5381dd3S12S0.53812 DD$0.50SMFbx knots 350.211$0.

45、50SMFbx knots 350.50SMFbx knots 25s113s0.2075dds12s0.2075dd3S12S0.20752 DD$0.67SMFbx knots 250.724$0.67SMFbx knots 250.724SMFbx knots 15s113s0.1688dds12s0.1688dd3S12S0.16882 DD$0.75SMFbx knots 150.792$0.75SMFbx knots 150.792A4.2.7 The stress modification factor for slope of grain is determined for e

46、ach zone from Table 4, using the factors forcompression for the zones above the neutral axis and the factors for tension for the zones below the neutral axis.SMFbx SOG6 = 0.87SMFbx SOG5 = 0.82SMFbx SOG4 = 0.66SMFbx SOG3 = 0.53SMFbx SOG2 = 0.69SMFbx SOG1 = 0.74A4.2.8 The stress modification factor fo

47、r each zone is determined using Eq A4.11.SMFbx6 = min0.75, 0.87 = 0.75SMFbx5 = min0.67, 0.82 = 0.67SMFbx4 = min0.5, 0.66 = 0.5SMFbx3 = min0.5, 0.53 = 0.5SMFbx2 = min0.724, 0.69 = 0.69SMFbx1 = min0.792, 0.74 = 0.74A4.2.9 The maximum stress permitted on each zone is calculated using Eq A4.12.D3737 122

48、2Fmax,6 = 1.4 (3500 psi) (0.75) = 3675 psiFmax,5 = 1.4 (3000 psi) (0.67) = 2814 psiFmax,4 = 1.4 (1930 psi) (0.50) = 1351 psiFmax,3 = 1.0 (1930 psi) (0.50) = 965 psiFmax,2 = 1.0 (3000 psi) (0.69) = 2070 psiFmax,1 = 1.0 (3500 psi) (0.74) = 2590 psiA4.2.10 The apparent outer fiber stress on the beam co

49、rresponding to Fmax, j for each zone is calculated using Eq A4.13.apparent,653675 psiS 1010.26DS2.12.1DS589.6666.7D53168 psiapparent,552814 psiS 109.26DS2.11.8DS589.6666.7D53135 psiapparent,451351 psiS 105.26DS2.11.1DS589.6666.7D54336 psiapparent,35965 psiS 102.74DS2.11.1DS589.6666.7D55946 psiapparent,252070 psiS 107.74DS2.11.8DS589.6666.7D52759 psiapparent,152590 psiS 109.74DS2.