ImageVerifierCode 换一换
格式:PDF , 页数:16 ,大小:154.28KB ,
资源ID:516022      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-516022.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D4001-2013 Standard Test Method for Determination of Weight-Average Molecular Weight of Polymers By Light Scattering《用低扩散法测定聚合物分子量和平均分子量的标准试验方法》.pdf)为本站会员(terrorscript155)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D4001-2013 Standard Test Method for Determination of Weight-Average Molecular Weight of Polymers By Light Scattering《用低扩散法测定聚合物分子量和平均分子量的标准试验方法》.pdf

1、Designation: D4001 93 (Reapproved 2006)D4001 13Standard Test Method forDetermination of Weight-Average Molecular Weight ofPolymers By Light Scattering1This standard is issued under the fixed designation D4001; the number immediately following the designation indicates the year oforiginal adoption or

2、, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This test method describes the test procedures for determining the weigh

3、t-average molecular weight Mw of polymers by lightscattering. It is applicable to all nonionic homopolymers (linear or branched) that dissolve completely without reaction ordegradation to form stable solutions. Copolymers and polyelectrolytes are not within its scope. The procedure also allows thede

4、termination of the second virial coefficient, A2, which is a measure of polymer-solvent interactions, and the root-mean-squareradius of gyration (s2)1/2, which is a measure of the dimensions of the polymer chain.1.2 The molecular-weight range for light scattering is, to some extent, determined by th

5、e size of the dissolved polymermolecules and the refractive indices of solvent and polymer. A range frequently stated is 10,000 to 10,000,000, but this may beis often extended in either direction with suitable systems and by the use of special techniques.1.2.1 The lower limit to molecular weight res

6、ults from low levels of excess solution scattering over that of the solvent. Thegreater the specific refractive increment dn/dc (difference in refractive indices of solution and solvent per unit concentration), thegreater the level of solution scattering and the lower the molecular weight that cansh

7、all be determined with a given precision.1.2.2 The upper limit to molecular weight results from the angular dependence of the solution scattering, which is determinedby the molecular size. For sufficiently large molecules, measurements must be made at small scattering angles, which are ultimatelyout

8、side the range of the photometer used.1.3 The values stated in SI units are to be regarded as standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and h

9、ealth practices and determine the applicability of regulatorylimitations prior to use.NOTE 1There areis no similar or equivalent ISO standards.known ISO equivalent to this standard.2. Referenced Documents2.1 ASTM Standards:2IEEE/ASTM SI-10 American National Standard for Use of the International Syst

10、em of Units (SI): The Modern Metric System3. Terminology3.1 DefinitionsUnits, symbols, and abbreviations are in accordance with IEEE/ASTM SI-10.4. Significance and Use4.1 The weight-average molecular weight is a fundamental structure parameter of polymers, which is related to many physicalproperties

11、 of the bulk material, such as its rheological behavior. In addition, knowledge of the weight-average molecular weight,together with knowledge of the number-average molecular weight from osmometry, provides a useful measure of the breadth ofthe molecular-weight distribution.4.2 Other important uses

12、of information on the weight-average molecular weight are correlation with dilute-solution ormelt-viscosity measurements and calibration of molecular-weight standards for use in liquid-exclusion (gel-permeation)chromatography.1 This test method is under the jurisdiction of ASTM Committee D20 on Plas

13、tics and is the direct responsibility of Subcommittee D20.70 on Analytical Methods.70.05).Current edition approved March 15, 2006Nov. 1, 2013. Published April 2006November 2013. Originally approved in 1981. Last previous edition approved in 19992006as D4001-93 (1999).-93 (2006). DOI: 10.1520/D4001-9

14、3R06.10.1520/D4001-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard a

15、nd is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only

16、 the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.3 To the extent that

17、 the light-scattering photometer is appropriately calibrated, light scattering is an absolute method and mayistherefore be applied to nonionic homopolymers that have not previously been synthesized or studied.5. Apparatus5.1 Volumetric Flasks, 100-mL, or other convenient size.5.2 Transfer Pipets.5.3

18、 Photometer, whose major components, described in Appendix X1, are a light source, a projection optical system, asample-cell area, a receiver optical system, a detector system, and a recording system. Typical photometers are described andsummarized (1)3 in the literature.5.4 Differential Refractomet

19、er, with sensitivity of approximately 3 106 refractive-index units, capable of measuring thespecific refractive increment dn/dc at the wavelength and temperature of the scattering measurements (2).NOTE 2Specific refractive increments are tabulated (2,3) for many polymer-solvent systems.5.5 Refractom

20、eter, Abb type or equivalent, capable of measuring the refractive indices of solvents and solutions at thewavelength and temperature of the scattering measurements.5.6 Spectrophotometer, capable of measuring the absorbance of solutions at the wavelength of the scattering measurements.5.7 Laminar-Flo

21、w Clean-Air Station, to provide a dust-free area for preparing and cleaning solutions and filling the scatteringcell.5.8 Filters and Filter Holders, for cleaning solvents and solutions. Membrane filters with pore sizes from 0.10 to 0.45 m, usedin glass or plastic filter holders, are recommended.5.8.

22、1 For water and aqueous solutions, and for organic solvents that do not attack the material, the use of polycarbonate(Nucleopore) filters is recommended. These filters have the advantages of high flow rate without the use of gas pressure, minimalretention of solute on the filter, and efficient clean

23、ing action. For other solvents, the use of cellulosic filters (Millipore or equivalent)is recommended.NOTE 3Sintered-glass filters may beis sometimes used, but these are relatively expensive and difficult to clean between uses. Centrifugation may beissometimes used, but this step requires special ca

24、re and techniques, or special scattering cell design, to be satisfactory.6. Reagents and Materials6.1 Solvents, as required. Since dn/dc is a function of composition, solvents shouldshall be of high purity. Significant errors inmolecular weight, which depends on the square of d n/dc, maywill be incu

25、rred if literature values of dn/dc are employed and theactual value of this quantity is different because of impurities in the solvent.6.2 12-Tungstosilicic Acid, as standard for calibration of photometer.7. Sample7.1 The sample must be homogeneous, and must be thoroughly free of all foreign impurit

26、ies. If at all possible, samples to beused for light-scattering measurements must be specially treated from synthesis on to minimize exposure to or contamination withparticulate impurities. Gels, which may Gels that consist of very high-molecular-weight particles, are sometimes formed duringsynthesi

27、s and will interfere with the analysis.All such particulate matter must be removed, sometimes with considerable difficulty.It should be understood that when this is done, the remaining sample is no longer truly representative of the entire polymer. Theextent of the difference from the original sampl

28、e will depend on the removal techniques employed.NOTE 4Reduction of sample particle size in a clean Spex or Wiley mill speeds solution and, with slow-dissolving materials, may be is essential ifthe measurements are to be made in a reasonable time. Overheating with consequent sample degradation must

29、be avoided during the milling process.Hard, tough samples or those with low melting points can be are handled by mixing with clean dry ice, milling the mixture, and then allowing the dryice to sublime. Clean dry ice may be obtained by opening a tank of carbon dioxide to the atmosphere. Commercial dr

30、y ice is usually has often been shownto be contaminated.8. Preparation of Dust-Free Cell and Contents8.1 Clean all glassware, including the scattering cell, with a suitable detergent to remove grease and other contaminants. Useof an ultrasonic cleaning bath is recommended. Rinse glassware at least f

31、our times with distilled water to remove all traces ofdetergent, and dry in a clean, dust-free drying oven.NOTE 5A laminar-flow clean-air station is recommended for providing a dust-free area for solution preparation and filtration. If a clean-air stationis not used, a closed area in a location free

32、 of drafts and of sufficient size to hold the filter unit, scattering cell, and other glassware shouldshall be provided.used.3 The boldface numbers in parentheses refer to the list of references at the end of this test method.D4001 1328.2 Filter solvent directly into the scattering cell. First rinse

33、 the cell several times with 5 to 10 mL of filtered solvent each, toremove dust particles. Be sure upper Upper surfaces of the interior of the cell are shall be well washed down. Close the cell witha cap similarly rinsed with filtered solvent. After rinsing, fill the cell with the minimum amount of

34、solvent required to bring theliquid level above the point where the light beam in the photometer passes through the cell.NOTE 6Use of a small filter holder fitting between a hypodermic syringe and needle is convenient where only small quantities of liquids need be arefiltered. A cell cap, with a hol

35、e just large enough to insert the needle, may conveniently be is used.8.3 Place the scattering cell in the photometer, or in an equivalent strong light beam, and examine it in the dark, viewing at smallscattering angles. Bright specks of dust shouldmust not be visible; if they are, the cell was not

36、rinsed completely or the filtrationprocedure is inadequate.8.4 Subsequent use of the clean cell for adding increments of filtered solution or for replacing solvent with solution requiresno further rinsing, except to ensure that residual solvent remaining, after the cell is emptied, is removed and re

37、placed with solution.9. Procedure9.1 Calibrate the light-scattering photometer. This calibration is required to convert measurements of scattered light intensityfrom arbitrary to absolute values, an essential step in the calculation of molecular weight. The calibration procedure, which islengthy and

38、 requires great care to obtain accurate results, is given in Appendix X2. The calibration constant of most photometersremains stable for long periods of time, however, so thatmaking the calibration procedure need be carried out onlyinfrequently.infrequent.9.2 Prepare a stock solution of polymer, not

39、ing the precautions of Sections 7 and 8, at a concentration estimated as follows: Fora polymer of Mw = 100,000 in a solventsuch that dn/d c 0.2 mL/g (for example, polystyrene in 2-butanone), the stock solution shouldshall be in the range from 10 to20 g/L. Since scattered intensity is proportional to

40、 Mw and to the square of dn/dc, estimates of the stock-solution concentrationrequired for other samples and systems can be is made. Prepare no more stock solution than is required by the following procedure.9.3 Select one of the following measurement schemes:9.3.1 Where the volume of liquid required

41、 for measurement in the photometer can be is varied by at least a factor of two, it isrecommended that the scattering from the minimum volume of solvent be measured first, followed by measurement of solutionsprepared in the cell by the addition of weighed or volumetrically measured aliquots of filte

42、red stock solution. From four to six suchsolutions shouldshall be measured, the most concentrated consisting of approximately equal volumes of solvent and stock solutionif its concentration is selected in accordance with 9.2, and the least concentrated being about one fourth this concentration. Aspe

43、cific example is given in Appendix X3.9.3.2 If the volume of liquid in the scattering cell cannot be varied as in 9.3.1, it will be is necessary to prepare and filter intothe cell from four to six separate solutions covering the range suggested in 9.3.1.9.3.3 A further alternative, which alternative

44、 is felt to be unduly complicated, is to to measure the most concentrated solutionfirst (for this purpose, the stock solution concentration estimated in 9.3.1 shouldshall be reduced by a factor of two), followed bysuccessive dilutions with solvent.The scattering from the pure solvent must be measure

45、d in a separate step, and it may be necessaryto step. If necessary, start dilution sequences at two or more concentration levels to obtain the range specified in 9.3.1.9.4 Measure the scattering of the pure solvent, filtered into the cell as described in Section 8, and of each of the series of filte

46、redsolutions described in 9.3, following the instructions provided with the photometer or in the literature (4), being sure that thefollowing steps are included. (This procedure is based on the scheme of 9.3.1.)9.4.1 Instrument CheckSee that the photometer is prepared for measurement, with the lamp

47、lit, high voltage supplied to thephotomultiplier detector, and all components fully warmed up and stabilized.9.4.2 Solvent PreparationFill the cleaned scattering cell with filtered solvent as described in Section 8, insert it in theinstrument, and align it as required.9.4.3 Intensity LevelSelect the

48、 wavelength-isolating filter to be used. Turn the detector to the specified angle and set the levelof high voltage, or adjust the slit openings, as called for to provide an appropriate solvent reading. In subsequent steps, do notreadjust these variables, but change amplifier gain by known factors or

49、 insert neutral filters of known transmittance as required tomaintain readings on scale.9.4.4 Solvent MeasurementAfter the cell has remained undisturbed in the photometer for 10 to 15 min to allow residual dustto settle out, read and record the scattered intensity at angles of 30, 90, 150, and at least three pairs between, symmetricallyplaced with respect to 90, as available on the photometer used.9.4.5 ReferenceTurn the phototube to the specified reference angle, adjust amplifier gain or insert neutral filters as required,insert the reference standard, and re

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1