ASTM D4228-2005(2017) Standard Practice for Qualification of Coating Applicators for Application of Coatings to Steel Surfaces《钢表面涂层涂刷油漆工的资格评定的标准实施规程》.pdf

1、Designation: D4228 05 (Reapproved 2017)Standard Practice forQualification of Coating Applicators for Application ofCoatings to Steel Surfaces1This standard is issued under the fixed designation D4228; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides a standard qualifying method forcoating applicators to verify the

3、ir proficiency and ability toattain the required quality for application of specified coatingsto steel surfaces including those in safety-related areas in anuclear facility.1.2 Variations or simplifications of the practice set forthherein may be appropriate for special coating work such asmaintenanc

4、e or qualifications of equipment suppliers shoppersonnel. It is not the intent of this practice to mandate asingular basis for all qualifications.1.3 Evaluation of the coating applicator being qualified inaccordance with this practice, shall be by qualified agents asspecified in 4.1. Reports shall b

5、e prepared as specified inSection 5, and certification as specified in Section 6.1.4 It is the intent of this practice to judge only the ability ofthe coating applicator to apply specified coatings with theproper tools and equipment.1.5 The values stated in inch-pound units are to be regardedas the

6、standard. The values given in parentheses are forinformation only.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health and environmental practices and de

7、ter-mine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mend

8、ations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Terminology2.1 Definitions:2.1.1 coating applicator, nan individual who has workedin the painting trade sufficiently long enough to master the useof all applicable tools and the materials being applied.2.1.2

9、governing documents, ntechnical specifications,jobsite procedures, and reference documents.2.1.3 qualifying agents, nthe designated representatives ofthe owner or of the coating organization, or both, who havesufficient experience in the practical application and evaluationof coatings applied to ste

10、el surfaces.3. Application of Coatings3.1 This practice requires the coating applicator to apply thespecified coating in conformance to the governing documentsto a test panel similar to that detailed in Fig. 1. A physical testarea may be selected by the owner/representative. The test areashall simul

11、ate job conditions and acceptance criteria shall bethe specification requirement. This panel is typical of the panelused for qualification, and may be modified to suit siteconfigurations.3.2 This practice requires the coating applicator to performthe application using the proper technique and applic

12、ationequipment consistent with the specified coating materials.3.3 The surfaces of the test panel shall be prepared inaccordance with the governing documents.3.4 Place the test panel approximately 12 in. (305 mm)above ground level and at approximately 30 from the verticalplane, with the complex side

13、 up. This will simulate the types ofdifficult coating situations encountered by coating applicators.3.5 The coating applicator shall demonstrate his ability toapply the specified coating to a uniform dry-film thickness inaccordance with the governing documents, as evaluated by thequalifying agents.3

14、.6 Allow required drying as prescribed by the governingdocuments prior to taking the dry-film thickness reading of theapplied coating. If a coating system specified requires multiplecoats, treat each coat as a separate application, allowing aspecified drying time before inspecting each completed coa

15、t.3.7 The coating applicator shall be provided with thefollowing:1This practice is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining Work for Power Generation Facilities and is the directresponsibility of Subcommittee D33.05 on Application and Surface Preparation.Current e

16、dition approved Sept. 1, 2017. Published September 2017. Originallyapproved in 1983. Last previous edition approved in 2012 as D4228 05 (2012).DOI: 10.1520/D4228-05R17.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international

17、standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.13

18、.7.1 Information regarding the specified coatingmaterial(s), including wet and dry film thickness required, andall other information contained in the governing documents forthe coating system being applied.3.7.2 Coating materials properly mixed in accordance withthe governing documents and ready for

19、 application.3.7.3 The necessary equipment for the proper application ofthe specified coating.3.7.4 Miscellaneous equipment, brushes, and thinners re-quired for cleaning the equipment after completion of the test.3.7.5 A practice area to adjust and test the equipment priorto performing the test.3.7.

20、6 All necessary safety equipment.3.7.7 Wet-film thickness gage for testing the coating thick-ness during application, where applicable.4. Evaluation of Coating Application4.1 Evaluation of the coating applicator shall be made bytwo qualifying agents. Only one qualifying agent can beproduction-relate

21、d.4.2 The qualifying agents shall be capable of answeringtechnical questions requested by the coating applicator relatingto the application of the specified coating material(s). Thequalifying agents shall be thoroughly familiar with the speci-fied coating material(s) and acceptance criteria and shal

22、l beaware of any difficulties in applying the coating to any surface.4.3 The qualifying agents shall have a wet-film gage of thesame type used by the coating applicator, as well as a calibratedmagnetic-type dry-film thickness gage.4.4 The qualifying agents shall take dry-film thicknessreadings on al

23、l areas of the test panel, except nuts and bolts.These readings shall be recorded as specified in Section 5.Wet-film readings may be used to check the coating applica-tors progress during application. The dry-film thickness read-ing shall be used to verify the specified dry-film thicknessrequirement

24、s and uniformity of application. The number andlocation of readings shall be as indicated on Fig. 2.4.5 The coating applicator and the qualifying agents shallunderstand the required dry-film thickness range requirementsof the governing documents before any coatings are applied.4.6 The qualifying age

25、nts shall inspect the finished surfaceto verify that it conforms to the requirements of the governingdocuments. A description of the appearance of the completedapplied coating and dry film thickness shall be recorded on theform shown in Fig. 2.5. Report5.1 The qualifying agents shall use a report fo

26、rm similar tothat in Fig. 2 to record dry-film thickness readings specified in4.4, and the appearance of the completed coating surface asspecified in 4.6 is recorded on a form similar to Fig. 3.5.2 The qualifying agents and coating applicator shall signthe report form.5.3 The generation of documenta

27、tion and maintenance ofrecords shall be as delineated in the applicable documents.FIG. 1 Test PanelComplex SideFIG. 2 Record Form for Test ApplicationD4228 05 (2017)26. Initial Qualification6.1 The qualifying agents shall prepare a form similar toFig. 3. The qualification form shall state the coatin

28、g materialsused and the application equipment used in the test.6.2 The qualifying agents and the coating applicator shallsign the qualification form.7. Requalification7.1 The owner or his designated representative may deter-mine the degree of requalification to be permitted, as well asthe acceptance

29、 of previously qualified coating applicatorsbased on time interval since the date of the qualification formand provided the same coating materials and applicationprocedures are used. Note the acceptance of previous qualifi-cation in the quality assurance file or the project.8. Limited Qualifications

30、Touch Up and Repair8.1 Limited qualifications can be accomplished using onlyareas representative of the actual plant surfaces, even thoughthey do not include all areas represented in Fig. 1.9. Limited QualificationsBrushes, Rollers, or, OtherSpecial Tools9.1 Limited qualifications for special applic

31、ation tools maybe required on certain projects. When such limited qualifica-tion is performed, the limitations shall be noted on the recordsfor qualification and application.10. Keywords10.1 applicator; qualifications, (initial, limited); qualifyingagents; report; requalificationsASTM International

32、takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own

33、 responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be add

34、ressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at

35、 the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585

36、(phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 3 Qualification FormD4228 05 (2017)3