ASTM D4295-1989(2005) Standard Classification for Rubber Compounding Materials-Zinc Oxide《橡胶配料-氧化锌的分类》.pdf

1、Designation: D 4295 89 (Reapproved 2005)Standard Classification forRubber Compounding MaterialsZinc Oxide1This standard is issued under the fixed designation D 4295; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last

2、revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This classification system covers the compounding ma-terial commercially known as zinc oxide. The types of zincoxide used

3、in the rubber industry are related to the productionprocess used. Typical chemical and physical properties areincluded.2. Referenced Documents2.1 ASTM Standards:2D 280 Test Methods for Hygroscopic Moisture (and OtherMatter Volatile Under the Test Conditions) in PigmentsD 3037 Test Methods for Carbon

4、 BlackSurface Area byNitrogen AdsorptionD 3280 Test Methods for Analysis of White Zinc PigmentsD 4075 Test Methods for Compounding MaterialsFlameAtomic Absorption TechniqueDetermination of MetalsD 4315 Test Methods for Rubber Compounding MaterialZinc Oxide3. Significance and Use3.1 Zinc oxide is an

5、important rubber compounding mate-rial. It is used to activate the organic accelerators to increasethe rate of vulcanization and to enhance physical properties. Itis also a vulcanizing agent for halogen-containing elastomers.4. Classification of Zinc Oxides by Types4.1 American Process or Direct Typ

6、eWhen zinc oxide ismanufactured by the reduction and reoxidation of a zinc-bearing material, such as a zinc ore by a carbonaceous fuel, itis called American process or direct type. American processzinc oxide is produced with widely varying chemical propertiesand physical characteristics. Nodular-typ

7、e particle shape, asobserved by the light microscope, is generally preferred forrubber compounding. Due to wide variations in the materialprocessed and in the process itself, the properties of Americanprocess zinc oxide can only be characterized in a general way.4.2 French Process or Indirect TypeWh

8、en zinc oxide ismanufactured by the burning of zinc vapor (produced byboiling zinc metal in a retort or zinc boiler), it is called Frenchprocess or indirect type. It is characterized by a high degree ofchemical purity resulting from the use of high purity (99.9%zinc). As generally produced, the part

9、icles are nodular in shapeas observed by the light microscope.4.3 Secondary Zinc Oxide Type:4.3.1 ChemicalWhen zinc oxide is manufactured as aby-product of a chemical reaction, it is considered a secondarytype. The chemical and physical properties can vary widelydepending on the raw material source

10、and the type of reaction.4.3.2 MetallurgicalWhen zinc oxide is manufacturedfrom burning zinc vapor produced by boiling die cast scrapzinc, galvanized zinc dross, or other scrap zinc units withoutpurification, it is considered a secondary type. The chemicalpurity can vary widely and is dependent on t

11、he purity of thefeed metal.5. Composition and Properties5.1 Typical properties for untreated zinc oxide by types aredescribed in Table 1.5.2 Treated Zinc OxideZinc oxide for use in rubber isoften surface treated, most frequently with a fatty acid such aspropionic acid.5.2.1 A fatty acid treated zinc

12、 oxide will typically containabout 0.5 % less zinc oxide than the corresponding untreatedgrade.5.2.2 The typical fatty acid treated zinc oxide shows agreater heat loss, about 0.2 %, than the corresponding untreatedgrade due to partial vaporization of the fatty acid.1This classification is under the

13、jurisdiction of ASTM Committee D11 onRubber and is the direct responsibility of Subcommittee D11.20 on CompoundingMaterials and Procedures.Current edition approved May 1, 2005. Published May 2005. Originallyapproved in 1983. Last previous edition approved in 1999 as D 4295 89(1999).2For referenced A

14、STM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Consho

15、hocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the ri

16、skof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of th

17、is standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake

18、 your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by

19、 contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Typical Properties of Zinc OxidePropertyASTMMethodAmericanType(Direct)French Type (Indirect) Secondary TypesClass 1 Class 2 Class 3 Chem

20、icalMetallurgicalClass 1 Class 2% Zinc oxide D 3280 99.0 99.5 99.5 99.5 95.0 99.0 99.0% Lead D 4075 0.10 0.002 0.002 0.002 0.10 0.10 0.10% Cadmium D 4075 0.05 0.005 0.005 0.005 0.05 0.05 0.05% Sulfur D 3280 0.15 0.02 0.02 0.02 0.15 0.02 0.02% Heat loss at 105C D 280 0.25 0.30 0.25 0.25 0.50 0.25 0.25% Sieve residue, 45 m D 4315 0.10 0.05 0.05 0.05 0.10 0.10 0.10Surface area, m2/g D 3037 3.5 9.0 5.0 3.5 40.0 5.0 3.5D 4295 89 (2005)2