ASTM D4360-2011 Standard Specification for Methyl n-Amyl Ketone《甲基n正戊基铜的标准规范》.pdf

1、Designation: D4360 11Standard Specification forMethyl n-Amyl Ketone1This standard is issued under the fixed designation D4360; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indic

2、ates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers methyl n-amyl ketone (98 %grade) for use in paint, varnish, lacquer, and related products.1.2 For specific hazard information and guida

3、nce, see thesuppliers Material Safety Data Sheet for materials listed in thisspecification.1.3 The following applies to all specified limits in thisstandard; for purposes of determining conformance with thisstandard, an observed value or a calculated value shall berounded off “to the nearest unit” i

4、n the last right-hand digitused in expressing the specification limit, in accordance withthe rounding-off method of Practice E29.2. Referenced Documents2.1 ASTM Standards:2D268 Guide for Sampling and Testing Volatile Solvents andChemical Intermediates for Use in Paint and RelatedCoatings and Materia

5、lD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)D1364 Test Method for Water in Volatile Solvents (KarlFischer Reagent Titration Method)D1613 Test Method for Acidity in Volatile Solvents andChemical Intermediate

6、s Used in Paint, Varnish, Lacquer,and Related ProductsD3893 Test Method for Purity of Methyl Amyl Ketone andMethyl Isoamyl Ketone by Gas ChromatographyD4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterD5386 Test Method for Color of Liquids Using Trist

7、imulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 Federal Specification:PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packagingof33. Properties3.1 Methyl n-amyl ketone shall conform to

8、 the followingrequirements:Apparent specific gravity20/20Cor25/25C0.8150.818or0.8120.815Color, Pt-Co scale, max (Note 1)10Distillation, 760 mm Hg, CInitial boiling point, minDry point, max147153.5Water, max, weight % 0.1Acidity, as acetic acid, max, weight % 0.02Purity, min, weight % 98NOTE 1Instrum

9、ental Pt-Co color determined by Test Method D5386have been shown to have no statistically significant difference from Pt-Cocolor determined by Test Method D1209. However, it is not knownwhether methyl n-amyl ketone was part of the sample set included in theinterlaboratory study.4. Sampling4.1 The ma

10、terial shall be sampled in accordance withPractice E300.5. Test Methods5.1 The properties enumerated in this specification shall bedetermined in accordance with the following ASTM methods.5.1.1 Apparent Specific GravityDetermine the specificgravity by any convenient method that is accurate to the th

11、irddecimal place, the temperature of both specimen and waterbeing 20 or 25C. (See Test Method D4052 and the SpecificGravity section of Guide D268.)5.1.2 ColorTest Method D1209.5.1.3 Distillation RangeTest Method D1078, using atemperature measuring device having a range of 95 to 255Cand a resolution

12、of 0.1C.5.1.4 WaterTest Method D1364.5.1.5 AcidityTest Method D1613.1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents, Plasticizers, and Chemical Intermediat

13、es.Current edition approved Nov. 1, 2011. Published December 2011. Originallyapproved in 1984. Last previous edition approved in 2003 as D4360 - 03. DOI:10.1520/D4360-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annu

14、al Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.1*A Summary of Changes section appear

15、s at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.6 PurityTest Method D3893.6. Packaging and Package Marking6.1 Package size to be agreed upon between the purchaserand the supplier.6.2 Packaging shall c

16、onform to applicable carrier rules andregulations or when specified shall conform to SpecificationPPP-C-2020.7. Keywords7.1 2-heptanone; MAK; methyl n-amyl ketone; solventsSUMMARY OF CHANGESCommittee D01 has identified the location of selected changes to this standard since the last issue(D4360 03)

17、that may impact the use of this standard. (Approved November 1, 2011.)(1) Added a new Note 1 in table in 3.1.(2) Added Test Method D5386 to the list of ReferencedDocuments.(3) Revised 5.1.3.(4) Removed Specification E1 from 2.1.ASTM International takes no position respecting the validity of any pate

18、nt rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision

19、at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comme

20、nts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted

21、 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D4360 112