ImageVerifierCode 换一换
格式:PDF , 页数:3 ,大小:68.23KB ,
资源ID:517288      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-517288.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM D4527-1999(2011) Standard Test Method for Carbon BlackSolvent Extractables《炭黑溶剂抽出物》.pdf)为本站会员(bowdiet140)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM D4527-1999(2011) Standard Test Method for Carbon BlackSolvent Extractables《炭黑溶剂抽出物》.pdf

1、Designation: D4527 99 (Reapproved 2011)Standard Test Method forCarbon BlackSolvent Extractables1This standard is issued under the fixed designation D4527; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A

2、 number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the procedure for measuringcarbon black solvent extractables.1.1.1 This test method determines the total mater

3、ial ex-tracted from carbon black by toluene under specified condi-tions. The procedure is also applicable to other solvents such ascyclohexane, etc.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not p

4、urport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For a specificprecautionary statement, see

5、 Section 7.2. Referenced Documents2.1 ASTM Standards:2D3051 Recommended Practice for Carbon BlackStatingthe Precision of ASTM Test Methods3D3396 Recommended Practice for Carbon BlackMeasuring the Precision of ASTM Test Methods33. Summary of Test Method3.1 A specimen of carbon black is extracted for

6、48 h (orother specified time) in a Soxhlet extractor, the solvent re-moved by controlled temperature evaporation, and the ex-tracted residue determined gravimetrically. If the carbon blackextractables are to be subjected to additional analysis, seeSection 7.4. Significance and Use4.1 The carbon blac

7、k extract test procedure provides auniform and precise method for the gravimetric determinationof organic-solvent extractables on carbon black. Accuracy andprecision are acceptable for most specification or regulatorypurposes, or both. However, carbon black with very low extract(less than 0.02 %) ma

8、y require a more rigorous extractionprocedure. The actual chemical composition of the extract canvary significantly with the type and origin of the carbon black.5. Apparatus5.1 Soxhlet Extraction Apparatus, with interchangeableground joints, 40 mm I.D. extraction tube, and 250-cm3flask.45.2 Extracti

9、on Thimble, glass, 35-mm diameter by 90-mmheight, with coarse porosity fritted disc.5When filled with 50cm3of toluene, drainage time for the first 40 cm3should notexceed 95 s. Discard thimbles taking longer.5.3 Heater, for extraction flask, with adjustable heat input.Ahot plate extraction heater or

10、hemispherical heating mantle ispreferred.5.4 Filter Funnel, glass fritted disc type, with mediumporosity fritted disc.5.5 Filter Flask, 125 or 250 cm3.5.6 Water Bath, or other suitable warming means for evapo-rating solvent from extract at a controlled temperature of 40 to50C.5.7 Container, suitable

11、 for final solvent removal and weigh-ing of residue. A lightweight aluminum dish 63 by 17.5 mm, aTFE-fluorocarbon cup or a 50-cm3glass beaker is suggested.65.8 Vacuum Oven, gravity-convection type, capable of tem-perature regulation within 61C at 125C and temperatureuniformity within 65C.1This test

12、method is under the jurisdiction of ASTM Committee D24 on CarbonBlack and is the direct responsibility of Subcommittee D24.31 on Non-CarbonBlack Components of Carbon Black.Current edition approved May 1, 2011. Published July 2011. Originally approvedin 1985. Last previous edition approved in 2004 as

13、 D4527 99 (2004). DOI:10.1520/D4527-99R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The las

14、t approved version of this historical standard is referencedon www.astm.org.4Fisher Scientific No. 9-556B available from Fisher Scientific Co., 203 FisherAve., Pittsburgh, PA 15219, has been found satisfactory. The use of KontasK-586100 (glass jacketed) available from Kontas Glass Co., 8000 Spruce S

15、t.,Vineland, NJ 08360, simplifies insulating the apparatus and reduces the possibilityof breakage.5Fisher Scientific 9-653B available from Fisher Scientific Co., has been foundsatisfactory.6Fisher Scientific No. 8-732-5C (aluminum dish) available from Fisher Scien-tific Co., and Ventron No. 2034 (te

16、flon cup) available from Ventron InstrumentCorp., Cahn Division, 16707 S. Carmenita Rd., Cerritos, CA 90701, have beenfound to be satisfactory.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.9 Oven, gravity-convection type, capable

17、 of temperatureregulation within 61C at 125C and temperature uniformitywithin 65C.5.10 Desiccator.5.11 Analytical Balance, with a sensitivity of 60.1 mg.6. Reagents and Materials6.1 Toluene, having a residue after evaporation less than 10ppm (preferably less than 2 ppm).76.2 Nitrogen.6.3 Glass wool,

18、 extracted with toluene, air-dried, followedby drying in a convection oven at 125C for 1 h. Store in aclosed container until ready to use.6.4 Aluminum Foil.7. Precautions7.1 For safety reasons, conduct the extraction and solventevaporation in an approved fume hood. Carbon blacks maycontain polynucle

19、ar aromatic compounds, some of which arecarcinogens. These compounds, when present, are so stronglybound to the carbon black that they are biologically inactive.However, they may be removed by extraction with toluene orother appropriate solvents. Avoid skin contact with solventextracts from such car

20、bon blacks.7.2 For most pelleted blacks, the depth of 60 mm in thethimble should provide a sample of 15 to 25 g. Unpelletedblacks should be predensified sufficiently that this depth willrequire a sample of at least 10 g.7.3 Do not use joint lubricant on the ground joints. Tominimize vapor loss by le

21、akage, the joints may be sealed withTFE-fluorocarbon inserts or wrapped with TFE-fluorocarbonlaboratory tape.7.4 New thimbles should be washed before use by suctionwith hot HCl and then rinsed with distilled or deionized waterto remove loose particles of foreign matter such as dust.Thimbles are conv

22、eniently cleaned by back washing undersuction with appropriate media (water, acetone, etc.). If thefritted disc becomes fouled with carbon black, it may benecessary to burn it out by slowly heating the thimble fromroom temperature to 500C in a muffle furnace. One hour isusually sufficient. The use o

23、f chromic acid cleaning solution isnot recommended. The permeability of the clean thimbleshould be checked periodically. Discard thimbles with drainagetimes exceeding the 95 s specified under 5.2.7.5 To prevent contamination, it is recommended that allglassware used in this procedure be reserved for

24、 the extractionof carbon black. If this is not feasible, the glassware must beextracted before use in accordance with 7.6.7.6 New glassware, including thimbles, must be extracted,repeatedly if necessary, with toluene or other solvent until theblank is acceptable (preferably less than 0.3 mg/150 cm3s

25、olvent).7.7 Two or three glass beads may be added to the extractionflask to promote smooth boiling. Do not use porous boilingchips.7.8 An extraction must be discarded if there is any visiblecarbon black in the extraction flask or if the thimble does notdrain properly and overflows at any time during

26、 the extraction.7.9 The nitrogen should be delivered through a glass ormetal tip. Do not allow plastic or rubber to contact the solvent.7.10 To protect from dust, a loose cover over the evapora-tion vessel is recommended.7.11 Solvent evaporation may be conducted in a vacuumevaporator, if available.7

27、.12 Any further analysis of the extracted material typicallyrequires that it be in solution. Complete re-solution of the dryextract may be difficult or impossible. Therefore, if furtheranalysis is to be performed, an additional sample of the carbonblack should be extracted and solvent removal carrie

28、d only tothe desired reduced volume. It is recommended that exposureto strong light, especially sunlight, be avoided during extrac-tion and subsequent handling, and that the extract be blanketedwith inert gas (nitrogen) if retained for any length of time.7.13 It has been found that there may be sign

29、ificant varia-tion in the amount of residue found in different bottles oftoluene bearing the same lot number. Consequently, blanksshould be run on each bottle.8. Procedure8.1 Dry an adequate specimen of the carbon black for1hinthe gravity-convection oven set at 125C in an open containerof suitable d

30、imensions so that the depth of the black is no morethan 10 mm. Cool and store the sample in a desiccator.8.2 Weigh, into a clean, dry extraction thimble, sufficientdried carbon black to fill the thimble to a depth of approxi-mately 60 mm. Record the weight of black to 0.1 g. Place aplug of glass woo

31、l above the black. Insert the thimble into theextraction tube, place 150 cm3of toluene in the extractionflask, and assemble the apparatus (see 7.1-7.6).8.3 Extract continuously for 48 h (or other time if specified),heating so that the cycle time between siphonings is 4 to 5 min(see 7.7). Wrap alumin

32、um foil loosely around the extractiontube and upper part of the flask to reduce heat loss. Terminatethe extraction with the extraction cup nearly full to reduce thequantity of solvent to be subsequently evaporated from theresidue in the extraction flask (See 7.8).8.4 Filter the contents of the extra

33、ction flask into a cleanfilter flask using moderate suction, rinsing the extraction flaskand filter funnel with several small portions of toluene.8.5 Evaporate the contents of the filter flask at 40 to 50Cuntil approximately 10 cm3remains. Direct a stream of drynitrogen onto the surface of the solut

34、ion to hasten evaporation(see 7.9-7.11).8.6 Transfer the remaining solution to the previously driedand weighed (to 0.1 mg) final container, rinsing the flask withseveral small portions of toluene. Continue evaporation toessentially dryness (see 7.12).8.7 To complete solvent removal to constant resid

35、ue mass,place the container in a vacuum oven at 40C. Setting thecontainer on the floor of the oven should be avoided; anon-conductive support or equivalent should be used. Slowly7Distilled-in-glass toluene available from Burdick and Jackson, 1953 T.S.Harvey, Muskegan, MI 49442 and Photrex grade avai

36、lable from J.T. BauerChemical Co., 223 Red School Ln., Phillipsburg, NJ 08865 are preferred products.Analytical reagent grade available from Mallinckrodt, Inc., 675-T McDonnell Blvd.,St. Louis, MO 63134 has generally been found acceptable.D4527 99 (2011)2reduce the oven pressure to approximately 3.3

37、 kPa andthereafter hold at that level. After a suitable time (usually 45min to 1 h), cool the container and contents to room tempera-ture in a desiccator and weigh to 0.1 mg. Return to the oven for15 min, cool, and reweigh. Repeat as necessary until the massis constant. Subtract the original mass to

38、 obtain the mass ofresidue.8.8 Make duplicate blank determinations on each bottle oftoluene placed in use. Follow this procedure exactly but omitthe carbon black (see 7.13).9. Calculation9.1 Calculate the mass percent extractables to the nearest0.01 % as follows:Extractables, mass % 5R 2 BW3 100 (1)

39、where:R = mass of residue, g,B = mass of residue from blank, g, andW = mass of carbon black sample, g.10. Report10.1 Report the following information:10.1.1 Proper identification of the sample,10.1.2 The solvent used,10.1.3 The extraction time, and10.1.4 The result obtained, reported to the nearest

40、0.01 %.11. Precision and Bias11.1 These precision data are based on single tests of threesamples by five laboratories on two days. The range of thesamples studied was from about 0.06 % to about 1.02 %.Precision is expressed in absolute terms.NOTE 1The precision is based on limited data in that only

41、fivelaboratories participated in the interlaboratory study.11.2 In test method statistical terminology, bias is thedifference between an average test value and the reference ortrue test property value. Reference values do not exist for thistest method since the value or level of the test property is

42、exclusively defined by this test method. Bias, therefore, cannotbe determined.11.3 Repeatability (Single-Operator)The repeatabilityhas been estimated to be 60.06 percentage points. Two testresults are significantly different if their difference exceeds0.09 percentage points.11.4 Reproducibility (Mul

43、tilaboratory)The reproducibil-ity has been estimated to be 60.09 percentage points. Two testresults are significantly different if their difference exceeds0.13 percentage points.NOTE 2This precision statement was developed following the guide-lines presented in Practices D3051 and D3396.12. Keywords

44、12.1 carbon black; cyclohexane; extract; silica gel adsorbentaromatic/polar fractions; solvent extractables; tolueneASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly a

45、dvised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, eith

46、er reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend.

47、 If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Indi

48、vidual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D4527 99 (2011)3

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1