ASTM D4882-2005 Standard Test Method for Bond Strength of Electrical Insulating Varnishes by the Twisted-Coil Test《用扭线试验测定电绝缘清漆粘结强度的标准试验方法》.pdf

1、Designation: D 4882 05An American National StandardStandard Test Method forBond Strength of Electrical Insulating Varnishes by theTwisted-Coil Test1This standard is issued under the fixed designation D 4882; the number immediately following the designation indicates the year oforiginal adoption or,

2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the bondstrength of an electrical i

3、nsulating varnish when applied to atwisted coil of film-insulated magnet wire. The use of aparticular type of film-insulated wire will show the values forthat combination of film coating and varnish.1.2 This standard does not purport to address all, if any, ofthe safety concerns, if any, associated

4、with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. A specific precau-tionary statement is given in Section 7.1.3 The values stated in inch-pound units are th

5、e standard.The values given in parentheses are for information only.NOTE 1Although this standard and Method C of IEC 61033 differ inapproach or detail, data obtained using either are technically equivalent.2. Referenced Documents2.1 ASTM Standards:2D115 Test Methods for Testing Solvent Containing Va

6、r-nishes Used for Electrical InsulationD 1711 Terminology Relating to Electrical InsulationD 2519 Test Method for Bond Strength of Electrical Insu-lating Varnishes by the Helical Coil TestD 6054 Practice for Conditioning Electrical Insulating Ma-terials for Testing2.2 IEC Standard:IEC 61033 Test Met

7、hods for the Determination of BondStrength of Impregnating Agents to an Enamelled WireSubstrate33. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 bond strength, na measure of the force required toseparate surfaces which have been bonded together.3.2 Refer to Terminology D 1711 f

8、or definitions of otherterms.4. Summary of Test Method4.1 Flexural strength tests are made on twisted coils todetermine the force required to break the coils under specificconditions.5. Significance and Use5.1 Values obtained by flexural test can provide informationwith regard to the bond strength o

9、f the particular varnish incombination with a particular type of magnet wire, whenmeasured under conditions described in this test method.6. Apparatus6.1 Coil winder as shown in Fig. 1 and Fig. 2.6.2 Coil Twister as shown in Fig. 3.6.3 Test apparatus as described in Test Method D 2519.7. Safety Prec

10、autions7.1 It is unsafe to use varnish at temperatures above theflash point without adequate ventilation, especially if thepossibility exists that flames or sparks are present. Storevarnish in sealed containers.8. Test Specimen Preparation8.1 The test specimen is a wound coil made from film-insulate

11、d magnet wire, 28 AWG (0.320 mm). The coil shall bemade by means of suitable winding equipment as shown in Fig.1. To prevent opening of the coil after removal from thewinding equipment, each end of the magnet wire, or shortpieces of film-insulated wire, may be wrapped around the coiltwo or three tim

12、es. For this purpose the winding equipment isprovided with appropriate notches as shown in Fig. 2. Forwinding the coil the following dimensions apply:Winding diameter 2.25 6 0.05 in. (57 6 1 mm)Width of slot .25 6 0.05 in. (6 6 1 mm)Number of turns 100 (See Note 2)Nominal wire diameter 28 AWG (0.320

13、 mm)NOTE 2Instead of 100 turns of a single wire, 50 turns of two parallelwires may be used to provide a bifilar winding.1This test method is under the jurisdiction ofASTM Committee D9 on Electricaland Electronic Insulating Materials and is the direct responsibility of SubcommitteeD09.01 on Electrica

14、l Insulating Varnishes, Powders, and Encapsulating Compounds.Current edition approved Sept. 1, 2005. Published September 2005. Originallyapproved in 1988. Last previous edition approved in 2001 as D 4882 01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer

15、 Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute, 25 W. 43rd St., 4thFloor, New York, NY 10036.1Copyright ASTM International, 100 Barr Harbor Drive,

16、PO Box C700, West Conshohocken, PA 19428-2959, United States.8.1.1 After the coil has been wound, remove it from thewinding equipment and stretch into an oval shape as shown inFig. 4. Twist the coil two full turns around its longitudinal axisby means of a twisting device as shown in Fig. 3. The twis

17、tedcoil formed is about 0.28 in. (7 mm) in diameter and 3.25 to 3.5in. (85 to 90 mm) in length and serves as a substrate for thevarnish.8.2 The type of magnet wire and test conditions shall bemutually agreed upon between all involved parties.8.3 Prepare six or more specimens for each condition to be

18、investigated.8.4 For solvent-containing varnishes, adjust the viscosity ofthe varnish by trial, to produce a dry film build of 0.0017 to0.0021 in. (.043 to .053 mm) on a double-coated copper panelcoated in accordance with Test Methods D115.8.5 Do not adjust solventless varnishes.8.6 Attach several t

19、wisted coils to a rack and immersevertically in the varnish until bubbling stops. Withdraw them at4 6 0.2 in./min (100 6 5 mm/min) and allow them to drainhorizontally for solventless varnishes 10 to 12 min at standardlaboratory atmosphere in accordance with Practice D 6054. Forsolvent-containing var

20、nishes drain vertically 10 to 12 min atstandard laboratory atmosphere in accordance with PracticeD 6054. Place the coils in an oven in the same position asdrained. Cure at the temperature and for the time recommendedby the manufacturer. Reverse dip the coils following thepreceding steps if testing a

21、 solvent-containing varnish.8.7 When testing solventless varnishes the twisted coils aresingle dipped.9. Procedure9.1 Follow the procedure as required in Test MethodD 2519.10. Report10.1 Report the data as required in Test Method D 2519.11. Precision and Bias411.1 PrecisionData from an interlaborato

22、ry study of thistest method are as follows:Data from six laboratories, 10 individual values from eachlaboratory per condition tested.Tested at 25 CMean 51 lbf (227 N)Standard Deviation 8.1 lbf (36 N)95 % Confidence level 15.9 lbf (71 N)Tested at 150 CMean 31 lbf (138 N)Standard Deviation 4.4 lbf (20

23、 N)95 % Confidence level 8.6 lbf (38 N)11.2 BiasThis test method has no bias because the valuefor bond strength of electrical insulating varnishes by thetwisted coil test is defined solely in terms of this test method.12. Keywords12.1 bond strength; electrical insulating; magnet wire;twisted coil; v

24、arnish4Supporting data are available from ASTM Headquarters. Request RR:D-9-1027.FIG. 1 Coil WinderFIG. 2 Coil Winder, Front ViewD4882052ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this sta

25、ndard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years an

26、dif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee,

27、which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-295

28、9,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 3 Coil TwisterFIG. 4 Oval-Shaped CoilD4882053