1、Designation: D4888 06 (Reapproved 2011)Standard Test Method forWater Vapor in Natural Gas Using Length-of-Stain DetectorTubes1This standard is issued under the fixed designation D4888; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision
2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a procedure for rapid andsimple field determination of water vapor in natural ga
3、spipelines. Availabel detector tubes provide a total measuringrange of 0.1 to 40 mg/L, although the majority of applicationswill be on the lower end of this range (that is, under 0.5 mg/L).At least one manufacturer provides tubes that read directly inpounds of water per million cubic feet of gas. Se
4、e Note 1.1.2 Detector tubes are usually subject to interferences fromgases and vapors other than the target substance. Such inter-ferences may vary among brands because of the use of differentdetection methods. Consult manufacturers instructions forspecific interference information. Alcohols and gly
5、cols willcause interferences on some water vapor tubes because of thepresence of the hydroxyl group on those molecules.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-pri
6、ate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Summary of Test Method2.1 The sample is passed through a detector tube filled witha specially prepared chemical. Any water vapor present in thesample reacts with the chemical to produce a color
7、 change orstain. The length of the stain produced in the detector tube,when exposed to a measured volume of sample, is directlyproportional to the amount of water vapor present in thesample. A hand-operated piston or bellows-type pump is usedto draw a measured volume of sample through the tube at ac
8、ontrolled rate of flow. The length of stain produced isconverted to milligrams per litre of H2O by comparison to acalibration scale supplied by the manufacturer for each box ofdetection tubes. The system is direct reading, easily portable,and completely suited to making rapid spot checks for waterva
9、por under field conditions.NOTE 1Detector tubes are available with calibration scales printed inpounds of water per million cubic feet of gas (lb/MMCF). The conversionfactor is 1 mg/L = 62.3 lb/MMCF (7 lb/MMCF = 0.11 mg/L).3. Significance and Use3.1 The measurement of water vapor in natural gas isim
10、portant because of the gas quality specifications, the corro-sive nature of water vapor on pipeline materials, and the effectsof water vapor on utilization equipment.3.2 This test method provides inexpensive field screening ofwater vapor. The system design is such that it may be used bynontechnical
11、personnel with a minimum of proper training.4. Apparatus4.1 Length-of-Stain Detector TubesA sealed glass tubewith the breakoff tips sized to fit the tube holder of the pump.The reagent layer inside the tube, typically a silica gel substratecoated with the active chemical, must be specific for waterv
12、apor and produce a distinct color change when exposed to asample of gas containing water vapor. Any substances knownto interfere must be listed in the instructions accompanying thetubes. A calibration scale should be marked directly on thetube; however, other markings that provide for ready interpre
13、-tation of water vapor content from a separate calibration scalesupplied with the tubes shall be acceptable. The calibrationscale shall correlate water vapor concentration to the length ofthe color stain. Shelf life of the detector tubes must be aminimum of two years from date of manufacture when st
14、oredaccording to manufacturers recommendations.4.2 Detector Tube PumpA hand-operated pump of apiston or bellows type. It must be capable of drawing 100 mLper stroke of sample through the detector tube with a volumetolerance of 65 mL.2It must be specifically designed for usewith detector tubes.NOTE 2
15、A detector tube and pump together form a unit and must beused as such. Each manufacturer calibrates detector tubes to match the1This test method is under the jurisdiction of CommitteeD03 on Gaseous Fuelsand is the direct responsibility of Subcommittee D03.07 Analysis of ChemicalComposition of Gaseou
16、s Fuels.Current edition approved Nov. 1, 2011. Published July 2012. Originally approvedin 1988. Last previous edition approved in 2006 as D4888 06. DOI: 10.1520/D4888-06R11.2Direct Reading Colorimetric Indicator Tubes Manual , First ed., AmericanIndustrial Hygiene Association, Akron, OH 44311, 1976.
17、1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.flow characteristics of its specific pump. Crossing brands of pumps andtubes is not permitted, as considerable loss of system accuracy is likely tooccur.24.3 Gas Sampling ChamberAny con
18、tainer that providesfor access of the detector tube into a uniform flow of samplegas at atmospheric pressure and isolates the sample from thesurrounding atmosphere. A stainless steel needle valve (orpressure regulator) is placed between the source valve and thesampling chamber for the purpose of thr
19、ottling the sampleflow. Flow rate should approximate one to two volume changesper minute or, at minimum, provide exit gas flow throughoutthe detector tube sampling period.NOTE 3Asuitable chamber may be devised from a polyethylene washbottle of nominal 500-mL (16-oz) or 1-L (32-oz) size. The wash bot
20、tlesinternal delivery tube provides for delivery of sample gas to the bottom ofthe bottle. A12-in. hole cut in the bottles cap provides access for thedetector tube and vent for the purge gas (Fig. 1).5. Procedure5.1 Select a sampling point that will provide access to arepresentative sample of the ga
21、s to be tested (source valve onthe main line). The sample point should be on top of thepipeline and equipped with a stainless steel sample probeextending to the middle third of the pipeline. Open the sourcevalve momentarily to clear the valve and connecting nipple offoreign materials.5.2 Install nee
22、dle valve (or pressure regulator) at the sourcevalve outlet. Connect sampling chamber using the shortestlength of tubing possible (Fig. 1). Many flexible tubingmaterials will be suitable for water vapor sampling; however, ifthe sampler is also used for other constituents such as hydrogensulfide, the
23、n tubing materials should be chosen carefully.Avoidusing tubing that reacts with or absorbs hydrogen sulfide, suchas copper or natural rubber. Use materials such as TFE-fluorocarbon, polyethylene, or stainless steel. Stainless steeltubing is preferred. (Warning Exiting gases are highlyflammable and
24、may contain toxic levels of hydrogen sulfide.Consider venting the exit gases away from the user whenpossible.)5.3 Open source valve. Open needle valve enough to obtainpositive flow of gas chamber, in accordance with 4.3. Purge thecontainer for at least 3 min (Fig. 1). Purge for at least 10 minif a p
25、olyethylene bottle is used.5.4 Before each series of measurements, test the pump forleaks by operating it with an unbroken tube in place. Consultmanufacturers instructions for leak check procedure detailsand for maintenance instruction if leaks are detected. The leakcheck typically takes 1 min.5.5 S
26、elect the tube range that best encompasses water vaporconcentration. Reading accuracy is improved when the stainlength extends into the upper half of the calibration scale.Consult manufacturer guidelines for using multiple strokes toachieve a lower range on a given tube.5.6 Break off the tube tips a
27、nd insert the tube into the pump,observing the flow direction indication on the tube. Place thedetector tube into the sampling chamber through the accesshole, such that the tube inlet is near the chamber center (Fig. 1).NOTE 4Detector tubes have temperature limits of 0 to 40C (32 to104F), and sample
28、 gases must remain in that range throughout the test.Cooling probes are available for sample tempertures exceeding 40C.5.7 Operate the pump to draw the measured sample volumethrough the detector tube. Observe tube instructions whenapplying multiple strokes. Ensure that a positive flow ismaintained t
29、hroughout the sample duration at the samplingchamber gas exit vent. Observe tube instructions for propersampling time per pump stroke. The tube inlet must remain inposition inside the sampling chamber until the sample iscompleted. Many detector tube pumps will have stroke finishindicators that elimi
30、nate the need to time the sample.NOTE 5It is very important to ensure that ambient air is not beingdrawn into the sample. Ambient humidity is often much higher than thewater vapor level in the gas sample, and intrusion could bias the readingshigh (for example, at 60F and 10 % relative humidity air c
31、ontains about83-lb H2O/MMCF or about 1.33 mg/L).5.8 Remove the tube from the pump and immediately readthe water vapor concentration from the tubes calibration scaleor from the charts provided in the box of tubes. Read the tubeat the maximum point of the stain. If “channeling” hasoccurred (nonuniform
32、 stain length), read the maximum andminimum stain lengths and average the two. Consult tubeinstructions for any special information in the event of multi-colored stains.NOTE 6If the calibration scale is not printed directly on the detectortube, be sure that any separate calibration chart is the prop
33、er match for thetube in use.5.9 If the number of strokes used differs from the number ofstrokes specified for the calibration scale, correct the readingfor water vapor concentration (WVC) as shown below (see also5.5):FIG. 1 Pump and Tube ApparatusD4888 06 (2011)2WVC corrected!5WVC reading!3specified
34、 strokesactual strokes(1)5.10 Record the reading immediately, along with the gastemperature and the barometric pressure. Observe any tem-perature corrections supplied in the tube instructions. Altitudecorrections become significant at elevations above 2000 ft.Correct for barometric pressure, as show
35、n below:WVC corrected!5WVC reading!3750 mm Hgbarometric pressure, mm Hg(2)NOTE 7Even though the amount of chemicals contained in detectortubes is very small, the tubes should not be disposed of carelessly. Ageneral disposal method includes soaking the opened tubes in water beforetube disposal. The w
36、ater should be treated to a neutral pH before itsdisposal.6. Quality Assurance6.1 Detector tubes from each batch or lot of tubes should betested to conform the published accuracy, (generally 6 25 %).6.2 The tubes should continue to meet the published accu-racy until the expiration date, if the tubes
37、 are shipped andstored per manufacturer instructions.7. Precision and Bias7.1 The accuracy of detector tube systems is generallyconsidered to be 625 %. This is based mainly on programsconducted by the National Institute of Occupational Safety andHealth (NIOSH) in certifying detector tubes for low-le
38、velcontaminants in air adapted to worker exposure monitoring.2NIOSH tested tubes at12 , 1, 2, and 5 times the threshold limitvalue (TLV), requiring 625 % accuracy at the three higherlevels and 635 % at the12 TLV level (for example, H2S witha TLV level of 10 ppm was tested at levels of 5, 10, 20, and
39、 50ppm). The higher tolerance allowed at the low level was due tothe loss accuracy for shorter stain lengths.3NIOSH discontin-ued this program in 1983, and it was picked up by the SafetyEquipment Institute (SEI) in 1986.8. Keywords8.1 gaseous fuels; natural gasASTM International takes no position re
40、specting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This
41、 standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Inter
42、national Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown b
43、elow.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-955
44、5 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).3“NIOSH Certification Requirements for Gas Detector Tube Units,” NIOSH/TC/A-012, July 1978.D4888 06 (2011)3
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1