ASTM D4924-1989(2017) Standard Classification for Petroleum Waxes for Use in Rubber Compounding《橡胶配合用石油蜡的标准分类》.pdf

1、Designation: D4924 89 (Reapproved 2017)Standard Classification forPetroleum Waxes for Use in Rubber Compounding1This standard is issued under the fixed designation D4924; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This classification is intended to establish a classifica-tion system and test methods for petroleum waxes used inrubb

3、er compounding primarily as a static protective agent ormaterial for unsaturated rubbers such as styrene-butadienerubber, polyisoprene rubber, natural rubber, chloroprenerubber, acrylonitrile-butadiene rubber, and polybutadiene rub-ber. These unsaturated rubbers are subject to ozone cracking.Under c

4、ertain exposure conditions, waxes retard this cracking.1.2 This classification is applicable to petroleum waxes usedas process aids in rubber compounding. It is not applicable tononpetroleum waxes such as carnuba wax, candelille wax, orceresin wax, nor to synthetic hydrocarbon waxes such aspolyethyl

5、ene wax. These non-petroleum waxes display a dif-ferent behavior on gas chromatographic analysis than dopetroleum waxes.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-pr

6、iate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D87 Test Method for Melting Point of Petroleum Wax(Cooling Curve)D445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids (and Calculat

7、ion of Dynamic Viscos-ity)D721 Test Method for Oil Content of Petroleum WaxesD938 Test Method for Congealing Point of PetroleumWaxes, Including PetrolatumD1321 Test Method for Needle Penetration of PetroleumWaxesD1500 Test Method for ASTM Color of Petroleum Products(ASTM Color Scale)D1747 Test Metho

8、d for Refractive Index of Viscous Mate-rialsD1833 Test Method for Odor of Petroleum WaxD2887 Test Method for Boiling Range Distribution of Pe-troleum Fractions by Gas ChromatographyD3944 Test Method for Solidification Point of PetroleumWaxD4419 Test Method for Measurement of Transition Tem-peratures

9、 of Petroleum Waxes by Differential ScanningCalorimetry (DSC)2.2 ASTM Committee Proposal:D02 Proposal P167 Test Method for Boiling Range Distri-bution of Crude Petroleum3NOTE 1A procedure using similar gas chromatographic methodologybut designed specifically for waxes is currently being developed by

10、ASTMCommittee D02.04.C.3. Summary of Classification3.1 The boiling point range of the petroleum wax is deter-mined by simulated distillation by gas chromatography (TestMethod D2887). If necessary, an internal standard is used todetermine the amount of material not volatile under theconditions of the

11、 chromatograph.3.2 Classification is made on the basis of the amount of thesample with normal boiling point above 538C (1000F).3.3 Further characterization is then done using other testmethods on the wax. In particular, the melting point behavior,color, odor, and viscosity when melted and refractive

12、 indexwhen melted have been found useful.4. Significance and Use4.1 Petroleum waxes in rubber compounds are commonlyused to provide protection from degradation by ozone understatic conditions, that is, when there is little or no flexing of therubber products. The mode of action for this protection i

13、s (1)migration of the wax through the rubber to the surface of theproduct and (2) the formation of an ozone impervious film onthe surface.1This classification is under the jurisdiction of ASTM Committee D11 onRubber and Rubber-like Materials and is the direct responsibility of SubcommitteeD11.20 on

14、Compounding Materials and Procedures.Current edition approved Feb. 1, 2017. Published March 2017. Originallyapproved in 1989. Last previous edition approved in 2012 as D4924 89 (2012).DOI: 10.1520/D4924-89R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Custom

15、er Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard

16、was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.14.2 This s

17、tandard classifies the petroleum waxes on thebasis of molecular weight. In general, waxes of lower molecu-lar weight (“paraffinic” or “crystalline”) migrate through therubber more rapidly and form more brittle film than the highermolecular weight waxes (“microcrystalline”). Wax mixturesand blends ar

18、e commonly used.4.3 No direct inference of suitability for use in a particularrubber compound is made or implied by the classificationsherein.5. Basis of Classification5.1 Determine the boiling point curve by gas chromato-graphic distillation, using Test Method D2887. The presence ofhigh boiling wax

19、 (carbon number 42) is indicated in TestMethod D2887 by a baseline that does not return to zero at anequivalent temperature of 538C. Internal standard methodsare used to determine the amount of high boiling material. It isoften useful to use cyclohexane or toluene both for a solvent toinject the wax

20、 into the gas chromatograph and for an internalstandard.5.2 Divide the boiling point distribution curve into two partsat a boiling point of 538C (1000F).5.3 Classify the wax according to Table 1.5.4 If desired, the wax can be further characterized asfollows:5.4.1 By determination of melting point be

21、havior by anyone of Test Methods D87, D938, D3944,orD4419; by certainchemical characteristics such as oil content (Test MethodD721) or odor (Test Method D1833); physical properties of thesolid wax such as hardness by needle penetration (Test MethodD1321), or properties of the molten wax such as visc

22、osity (TestMethod D445), color (Test Method D1500), clarity, andfreedom from foreign solids (inspection only) and RefractiveIndex (Test Method D1747). These properties are of limitedimportance for wax used as a protective agent but may affectother properties of the rubber compounds. They are also us

23、edto control lot to lot variation.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risko

24、f infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this

25、standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake yo

26、ur views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by co

27、ntacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Classification of WaxType Wax DesignationMass Wax ofBoiling Point538C, %A paraffin 30D4924 89 (2017)2