ASTM D5003-2006a(2011) Standard Test Method for Hardgrove Grindability Index (HGI) of Petroleum Coke《石油焦的哈德格罗夫可磨性指数(HGI)的标准试验方法》.pdf

1、Designation: D5003 06a (Reapproved 2011)Standard Test Method forHardgrove Grindability Index (HGI) of Petroleum Coke1This standard is issued under the fixed designation D5003; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the yea

2、r of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONIntroduction of petroleum coke into the coal market in recent years has necessitated the use of manyof the test m

3、ethods for coal so like data would be available for comparison and blending purposes. TestMethod D409 does not cover petroleum coke in its scope and its statements of precision and bias donot include petroleum coke. This test method provides the procedures and precision and bias data forthe hardgrov

4、e grindability index (HGI) of petroleum coke. Use of this test method or Test MethodD409 produces the same value for the sample of petroleum coke being analyzed.1. Scope1.1 This test method covers the determination of the hard-grove grindability index (HGI) of those petroleum cokes thatcontain no de

5、dusting additive. The procedure for this testmethod is the same as in Test Method D409. Sections of thistest method contain the significance and use of the HGI ofpetroleum coke, preliminary sample preparation procedures,and procedure and precision and bias data specific to petroleumcoke.NOTE 1The si

6、ze consistency (particle size distribution) of fluidpetroleum coke is generally 100 % passing a 6.73 mm (No. 3) sieve andgreater than 80 % passing a 2.00 mm (No. 10) sieve. Much of fluid cokeswill pass a 0.59 mm (No. 30) sieve. Because of this fineness the HGI valueis related to the coarser particle

7、s in fluid coke and large samples arerequired to prepare sufficient material of the correct particle size for TestMethod D409.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.2.1 ExceptionHardgrove grindability index is uni

8、tless.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Refere

9、nced Documents2.1 ASTM Standards:2D409 Test Method for Grindability of Coal by theHardgrove-Machine MethodD4930 Test Method for Dust Control Material on CalcinedPetroleum Coke3. Terminology3.1 Definitions:3.1.1 calcined petroleum coke, npetroleum coke that hasbeen thermally treated to drive off the

10、volatile matter and todevelop crystalline structure.3.1.2 fluid coke, npetroleum coke with a granular, micro-scopic layered structure resulting from injection of petroleumfeedstock into a flowing, loose bed of coke particles.3.1.3 Hardgrove Grindability Index, HGI, unitless, ninpetroleum coke techno

11、logy, measurement of the relative ease ofpulverizing a raw petroleum coke or green petroleum coke incomparison with coal standards. The higher the HGI value, theeasier the petroleum coke is to grind.3.1.4 petroleum coke, nsolid, carbonaceous residue pro-duced by thermal decomposition of heavy petrol

12、eum fractionsor cracked stocks, or both.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.05 on Properties of Fuels, Petroleum Coke and Carbon Material.Current edition approved May 1, 2011. Publis

13、hed August 2011. Originallyapproved in 1989. Last previous edition approved in 2006 as D500306a. DOI:10.1520/D5003-06A.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer

14、to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.5 raw petroleum coke, npetroleum coke that has notbeen calcined.4. Summary of Test Method4.1 The sample of petroleum coke i

15、s reduced (crushed) toproduce a high yield of particles passing a 1.19 mm (No. 16)sieve and retained on a 0.59 mm (No. 30) sieve. These particlesare reduced in the hardgrove grindability machine according toTest Method D409. The quantity of particles retained on a0.074 mm (No. 200) sieve is used to

16、calculate the HGI of thesample.5. Significance and Use5.1 The HGI is used to predict the ranking of raw petroleumcokes or calcined petroleum cokes in industrial size mills usedfor crushing operations. The rankings are based on energyrequired and feed rate or both.5.2 The HGI is also used to select r

17、aw petroleum cokes andcoals that are compatible with each other when milled togetherin a blend so that segregation of the blend does not occurduring particle size reduction.6. Hazards6.1 Calcined petroleum coke is generally coated with adedusting agent to decrease the occurrence and the quantity ofd

18、ust during subsequent transporting of the calcined petroleumcoke. The dedusting agent is an oil or suitable material. Whena dedusting agent is present and is not removed prior to thedetermination of HGI there can be interference in the sievingstep to measure the portions retained on and passing a 0.

19、074mm (No. 200) sieve. Removal of the dedusting agent aftercalcined petroleum coke is reduced to pass the 4.76 mm (No.4) sieve and before stage crushing to pass the 1.19 mm (No. 16)sieve is required. Suitable solvents for oil removal are dichlo-romethane, dichloroethane and toluene. (WarningSee thea

20、ppropriate materials safety data sheet.) The solvent used mustbe removed prior to the reduction to pass the 1.19 mm (No. 16)sieve. Heating to 10C above the boiling point of the solventused or application of vacuum is satisfactory for the removal.7. Sampling and Sample Preparation7.1 A guide for samp

21、ling petroleum cokes and calcinedcoke3and a practice for preparing samples of petroleum cokeare in the ASTM process of development and will be refer-enced when they are available. The sample preparation in TestMethod D409 is adequate.7.2 When a dedusting agent is present remove it in themanner requi

22、red by the supplier of the calcined petroleumcoke. The supplier knows what the added agent is, and shouldbest know how to remove it. See Test Method D4930.8. Procedure8.1 The procedure (including apparatus) for raw petroleumcoke and for calcined petroleum coke having no dedustingagent is the same as

23、 listed in Test Method D409.9. Precision and Bias9.1 PrecisionThe statements for repeatability and repro-ducibility for petroleum coke and calcined petroleum coke arebeing developed following RR:D02-1007.49.2 BiasThe procedure in this test method has no biasbecause the value of the hardgrove grindab

24、ility index can bedefined only in terms of the test method.10. Keywords10.1 coke; grindability; petroleum cokeANNEX(Mandatory Information)A1. TEST METHOD D409A1.1 Test Method D409 is under the jurisdiction of ASTMCommittee D05 on Coal and Coke. Committee D02 follows allrevisions and modifications of

25、 Test Method D409 throughliaison contact with Committee D05. ASTM Committee D02will revise other sections of this test method when necessary toconform to changes in Test Method D409.3The guide and practice are being developed by ASTM Committee D02 onPetroleum Products and Lubricants.4Filed at ASTM I

26、nternational Headquarters and may be obtained by requestingResearch Report RR:D02-1007.D5003 06a (2011)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that

27、determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapprove

28、d or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel

29、 that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual repri

30、nts (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5003 06a (2011)3