ASTM D5100 D5100M-1995a(2010)e1 Standard Test Method for Adhesion of Mineral Aggregate to Hot Bitumen《矿物集了与热沥青粘合性的标准试验方法》.pdf

1、Designation: D5100/D5100M 95a (Reapproved 2010)1Standard Test Method forAdhesion of Mineral Aggregate to Hot Bitumen1This standard is issued under the fixed designation D5100/D5100M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision,

2、the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEUnits information was corrected editorially in July 2010.1. Scope1.1 This test method determines the adhesion of

3、mineralaggregate when applied over a pour coat of hot bitumen on aroof membrane.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of th

4、e other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health prac

5、tices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D226 Specification forAsphalt-Saturated Organic Felt Usedin Roofing and WaterproofingD312 Specification for Asphalt Used in RoofingD450 Specification for Coal-Tar Pitch Used in Ro

6、ofing,Dampproofing, and WaterproofingD1079 Terminology Relating to Roofing and Waterproofing3. Terminology3.1 DefinitionsFor definitions of terms used in this testmethod, see Terminology D1079.4. Summary of Test Method4.1 Asmall section of roof surface is fabricated with roofingfelt or membrane usin

7、g measured amounts of a bituminouspour coat and mineral aggregate surfacing. The assembly isallowed to cool, the loose aggregate is removed and weighed,and the mass of adhered aggregate is calculated and reported.5. Significance and Use5.1 The quantities of mineral aggregate adhered to thesurface of

8、 a roof vary with the characteristics and total amountof the aggregate. Mineral aggregate shields bituminous mem-branes from solar radiation. Unadhered mineral aggregate canbe displaced by wind, water, and traffic, exposing the bitumen.5.2 This test method provides a laboratory means of deter-mining

9、 and recording the mass of aggregate that adheres to abituminous pour coat.6. Apparatus6.1 Steel Tray, measuring 143 mm 558 in. 6 1 % squareby 13 mm 0.5 in. 6 10 % in height.6.2 Scales, for weighing bitumen and mineral aggregate,balance 1.00-kg 2.2-lb capacity, sensitive to 0.01 % of thecapacity.6.3

10、 Containers, for hot bitumen and mineral aggregate (1-L1-qt capacity).7. Procedure7.1 Cut a piece of saturated felt to just cover the bottom ofthe steel tray; the saturated felt shall be Type 1 complying withSpecification D226.7.2 Attach the saturated felt to the inside of the tray with athin film o

11、f a release agent such as silicone stopcock grease orpetroleum jelly. Lightly grease the insides of the sides of thetray with the same material.7.3 Weigh out 400 g 0.88 lb of gravel, chert, or trap rock,or 300 g 0.66 lb of slag mineral aggregate surfacing 61%.Record this mass as A. This is equivalen

12、t to 19.5 kg/m2400lb/100 ft2 and 14.6 kg/m2300 lb/100 ft2, respectively.7.4 Apply top pour coat of bitumen uniformly according toquantities and temperatures listed in Table 1.7.5 Immediately apply mineral aggregate into hot bitumenand spread uniformly over entire surface within the tray.Allowthe ass

13、embly to cool for 30 min minimum.7.6 Turn sample upside down and collect loose aggregate.Weigh the loose aggregate and record this mass as B.1This test method is under the jurisdiction ofASTM Committee D08 on Roofingand Waterproofing and is the direct responsibility of Subcommittee D08.03 onSurfacin

14、g and Bituminous Materials for Membrane Waterproofing and Built-upRoofing.Current edition approved July 1, 2010. Published July 2010. Originally approvedin 1990. Last previous edition approved in 2005 as D5100 95a (2005). DOI:10.1520/D5100_D5100M-95AR10E01.2For referenced ASTM standards, visit the A

15、STM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, Uni

16、ted States.7.7 Repeat the procedure three more times, recording eachindividual mass determination.8. Calculation8.1 Calculate the mass of the adhered aggregate for each testas:C 5 A 2 B (1)where:C = mass of the adhered aggregate in pounds per squarefoot (4.88 (A B) gives the mass of the adheredaggre

17、gate in kg/m2).8.2 Calculate the mean mass of the adhered aggregate Cmbydividing the sum of the four determinations by four.8.3 Calculate an estimate of the standard deviation s by:s 54(C22 (C!212(2)8.4 Calculate the standard error of the mean S by:S 5s2(3)9. Report9.1 Report the following informati

18、on:9.1.1 The type of aggregate, including screen grading, andthe type of bitumen used.9.1.2 The mass of the adhered aggregate for any singledetermination as Cm6 3.18 3 s (95 % level of confidence).9.1.3 The mean mass of adhered aggregate as Cm63.18 3 S.10. Precision and Bias10.1 PrecisionThe precisi

19、on of this test method dependson the characteristics of the mineral aggregate.The precision ofany single test series can be estimated from the statisticsrequired by the test method. Differences between laboratoriescan be tested with standard statistical techniques such as thenull hypothesis.10.2 Bia

20、sThe procedure of this test method for theadhesion of mineral aggregate to hot bitumen has no biasbecause the quantity of aggregate adhered in the laboratory isdefined by this test method.11. Keywords11.1 adhered mineral aggregate; hot bitumen; roofmembraneASTM International takes no position respec

21、ting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This sta

22、ndard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Internati

23、onal Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below

24、.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (f

25、ax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Bitumen Application Rates and TemperaturesASTM Standard TypeApplicationTemperatureC FApplication RateSpecification D312 IIIIIIIV177 6 14 3506 25 204 6 14 4006 25218 6 14 425 6 25232 6 14 4506 2560 g/tray or 2.9 kg/m260 lb/100 ft2Specification D450 IIII182 6 14 360 6 25191 6 14 375 6 2575 g/tray or 3.7 kg/m275 lb/100 ft2D5100/D5100M 95a (2010)12