ASTM D5350-1995(2006) Standard Test Method for Determination of Organically Combined Sulfuric Anhydride by Titration Test Method A《用滴定测试法A测量有机合成三氧化硫的标准试验方法》.pdf

1、Designation: D 5350 95 (Reapproved 2006)Standard Test Method forDetermination of Organically Combined Sulfuric Anhydrideby Titration, Test Method A1This standard is issued under the fixed designation D 5350; the number immediately following the designation indicates the year oforiginal adoption or,

2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the organi-cally combined sulfuric

3、anhydride existing in a sample ofsulfated oil by boiling the sample with sulfuric acid anddetermining the acidity of the reaction mixture. This testmethod is applicable only to oils that split off their combinedSO3upon boiling with mineral acids and that do not containcompounds that cannot be accura

4、tely titrated in water solutionwith methyl orange as the indicator. This test method wasderived from Test Methods D 500, Sections 15 through 19.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are provided forinformation only.1.3 This standard does

5、 not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Stand

6、ards:2D 500 Test Methods of Chemical Analysis of Sulfonatedand Sulfated Oils3. Significance and Use3.1 This test method is intended for the determination oforganically combined sulfuric anhydride in sulfated oils.4. Apparatus4.1 The apparatus required consists of a glass flask providedwith a glass s

7、topper and an air condenser. The connectionbetween the flask and the condenser shall be a ground joint.Perforated glass beads shall be used to prevent bumping.4.1.1 Flask, an Erlenmeyer flask (Fig. 1) made of borosili-cate glass, having a capacity of approximately 300 mL andprovided with a glass sto

8、pper.4.1.2 CondenserThe condenser required consists of aglass tube, 915 mm (36 in.) in length, and 8 mm (516 in.) inoutside diameter. The lower end of the tube shall be flared andground to fit the mouth of the Erlenmeyer flask.4.1.3 Glass Beads, perforated glass beads, made of chemi-cally resistant

9、glass, approximately 4 mm (532 in.) in diameter.Before using, the glass beads shall be boiled thoroughly inseveral portions of water or until the wash water reacts neutralto methyl orange indicator.5. Reagents5.1 Ethyl Ether.5.2 Methyl Orange Indicator Solution (1 g/L)Dissolve 0.1g of methyl orange

10、in 100 mL of water.5.3 Sodium Chloride (NaCl), solid.5.4 Sodium Hydroxide, Standard Solution (1 N)Accurately prepare and standardize a 1 N sodium hydroxide(NaOH) solution. Express the strength or concentration of thesolution as milligrams of KOH per millilitre; 1 mL of 1 NNaOH solution is equivalent

11、 to 56.1 mg of KOH.5.5 Sodium Hydroxide, Standard Solution (0.5 N)Accurately prepare and standardize a 0.5 N NaOH solution.Express the strength of the solution as milligrams of KOH permillilitre; 1 mL of 0.5 N NaOH solution is equivalent to 28.05mg of KOH.5.6 Sulfuric Acid, Standard (0.5 N)Accuratel

12、y prepareand standardize a 0.5 N sulfuric acid (H2SO4) solution. Expressthe strength of the solution as milligrams of KOH per millilitre;1mLof0.5N H2SO4is equivalent to 28.05 mg of KOH.1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Sub

13、committee D31.08 on Fats and Oils. This testmethod was developed in cooperation with the American Leather Chemists Assn.(Method H 421957).Current edition approved April 1, 2006. Published April 2006. Originallyapproved in 1993. Last previous edition approved in 2001 as D 5350 95(2001).2For reference

14、d ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Con

15、shohocken, PA 19428-2959, United States.5.7 Sulfuric Acid (1+19)Carefully mix one volume ofconcentrated sulfuric acid (H2SO4, sp gr 1.84) into 19 volumesof water while stirring.6. Procedure6.1 The procedure consists of two determinations: namely,(1) the alkalinity of the sample, designated as A, and

16、 (2) theincrease in acidity after boiling the sample with sulfuric acid,designated as F.6.1.1 Alkalinity, ADissolve 10 g of the sample in 100 mLof water in the 300-mL glass-stoppered Erlenmeyer flask,warming to obtain solution, if necessary. After cooling, add 30g of NaCl, 25 mL of ether, and five d

17、rops of methyl orangeindicator solution; then add 0.5 N H2SO4with frequent butgentle shaking until the mixture is slightly acid. Shake thecontents of the flask vigorously, and complete the titration byadding first 0.5 N NaOH solution several drops at a time untilthe solution is alkaline and then the

18、 acid one or two drops at atime until the end point is reached. Shake the solutionvigorously after each addition of reagent. Drain burets for 3min before taking readings. Calculate the alkalinity, A,asfollows:A 5 B 3 D! 2 C 3 E!#/W (1)where:A = total alkalinity, mg of KOH/g,B = millilitres of H2SO4r

19、equired for titration of thesample,C = millilitres of NaOH solution required for titration ofthe sample,D = strength of H2SO4, mg of KOH/mL,E = strength of NaOH solution, mg of KOH/mL, andW = weight of sample, g.6.1.2 Increase in Acidity upon Boiling, FWeigh 10 g ofthe sample into the Erlenmeyer fla

20、sk and boil under the aircondenser with H2SO4(1+19) for 112 h or until both the oil andwater layers are perfectly clear, using glass beads to preventbumping. The volume of H2SO4added shall be sufficient toneutralize the total alkalinity, A, of the sample plus 25 mL inexcess. Regulate the heating so

21、that the solution boils rathervigorously but with very little evaporation taking place. At theend of the heating period allow the contents to cool, wash thecondenser with a spray of water from a wash bottle, anddisconnect the condenser.Add 30 g of NaCl, 25 mL of ether, 50mL of water, and five drops

22、of indicator solution and titrate thesolution with 1 N NaOH solution to the same end point as inthe total alkalinity titration, 6.1.1. During the titration stopperthe flask frequently and shake the contents of the flaskthoroughly. Drain the burets for 3 min before readings aretaken.NOTE 1Reserve the

23、 titrated solution for the subsequent determinationof total desulfated fatty matter (Section 29 to 32 of Test Methods D 500).6.1.2.1 Make a blank determination simultaneously with thesample, using the same amount and strength of the H2SO4,approximately the same weight of glass beads, and heating and

24、titrating under the same conditions as the sample.6.1.2.2 Calculate the increase in acidity upon boiling, F,asfollows:F 5 S 2 B!N/W (2)where:F = increase in acidity (Note 2) upon boiling, mg ofKOH/g,S = millilitres of NaOH solution required for titration ofthe sample,B = millilitres of NaOH solution

25、 required for titration ofthe blank,N = strength of NaOH solution, mg of KOH/mL, andW = weight of sample, g.NOTE 2The increase in acidity, F, may be negative, in which caseretain the sign obtained from the equation in Section 7.7. Calculation7.1 Calculate the percentage of organically, combined sul-

26、furic anhydride as follows:Organically combined sulfuric anhydride, % 5 0.1426A 1 F! (3)where:0.1426 = one tenth of the molecular ratio of SO3:KOH,A = total alkalinity, mg of KOH/g, andF = increase in acidity upon boiling, mg of KOH/g.= Retain the sign of F as obtained in 6.1.2.8. Precision and Bias

27、8.1 Although this test method is widely used, precision andbias information is not available at this time.9. Keywords9.1 leather; sulfated oils; sulfuric anhydride; titrationFIG. 1 Apparatus for Determination of Organically CombinedSulfuric Anhydride, Test Method AD 5350 95 (2006)2ASTM International

28、 takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their ow

29、n responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be ad

30、dressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, a

31、t the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 5350 95 (2006)3