ASTM D5453-2008b 809 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons Spark Ignition Engine Fuel Diesel Engine Fuel and Engine Oil by Ultraviolet Fluore.pdf

1、Designation: D 5453 08bAn American National StandardStandard Test Method forDetermination of Total Sulfur in Light Hydrocarbons, SparkIgnition Engine Fuel, Diesel Engine Fuel, and Engine Oil byUltraviolet Fluorescence1This standard is issued under the fixed designation D 5453; the number immediately

2、 following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This test

3、method covers the determination of total sulfurin liquid hydrocarbons, boiling in the range from approxi-mately 25 to 400C, with viscosities between approximately0.2 and 20 cSt (mm2/S) at room temperature.1.2 Three separate interlaboratory studies (ILS) on preci-sion, and three other investigations

4、that resulted in an ASTMresearch report, have determined that this test method isapplicable to naphthas, distillates, engine oil, ethanol, FattyAcid Methyl Ester (FAME), and engine fuel such as gasoline,oxygen enriched gasoline (ethanol blends, E-85, M-85, RFG),diesel, biodiesel, diesel/biodiesel bl

5、ends, and jet fuel. Samplescontaining 1.0 to 8000 mg/kg total sulfur can be analyzed(Note 1).NOTE 1Estimates of the pooled limit of quantification (PLOQ) for theprecision studies were calculated. Values ranged between less than 1.0 andless than 5.0 mg/kg (see Section 8 and 15.1).1.3 This test method

6、 is applicable for total sulfur determi-nation in liquid hydrocarbons containing less than 0.35 %(m/m) halogen(s).1.4 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety

7、 concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For warningstatements, see 3.1, 6.3, 6.4, Section 7, and 8.1.2. Referenced D

8、ocuments2.1 ASTM Standards:2D 1298 Test Method for Density, Relative Density (SpecificGravity), or API Gravity of Crude Petroleum and LiquidPetroleum Products by Hydrometer MethodD 4052 Test Method for Density and Relative Density ofLiquids by Digital Density MeterD 4057 Practice for Manual Sampling

9、 of Petroleum andPetroleum ProductsD 4177 Practice for Automatic Sampling of Petroleum andPetroleum ProductsD 6299 Practice for Applying Statistical Quality Assuranceand Control Charting Techniques to Evaluate AnalyticalMeasurement System Performance3. Summary of Test Method3.1 A hydrocarbon sample

10、is either directly injected orplaced in a sample boat. The sample or boat, or both, is insertedinto a high temperature combustion tube where the sulfur isoxidized to sulfur dioxide (SO2) in an oxygen rich atmosphere.Water produced during the sample combustion is removed andthe sample combustion gase

11、s are next exposed to ultraviolet(UV) light. The SO2absorbs the energy from the UV light andis converted to excited sulfur dioxide (SO2*). The fluorescenceemitted from the excited SO2* as it returns to a stable state,SO2, is detected by a photomultiplier tube and the resultingsignal is a measure of

12、the sulfur contained in the sample.(WarningExposure to excessive quantities of ultraviolet(UV) light is injurious to health. The operator must avoidexposing any part of their person, especially their eyes, notonly to direct UV light but also to secondary or scatteredradiation that is present.)1This

13、test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.03 on Elemental Analysis.Current edition approved July 1, 2008. Published August 2008. Originallyapproved in 1993. Last previous edition approved in 200

14、8 as D 545308a.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the

15、end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4. Significance and Use4.1 Some process catalysts used in petroleum and chemicalrefining can be poisoned when trace amounts of sulfur bearingmaterials are contained

16、in the feedstocks. This test method canbe used to determine sulfur in process feeds sulfur in finishedproducts, and can also be used for purposes of regulatorycontrol.5. Apparatus5.1 FurnaceAn electric furnace held at a temperature(1075 6 25C) sufficient to pyrolyze all of the sample andoxidize sulf

17、ur to SO2.5.2 Combustion TubeA quartz combustion tube con-structed to allow the direct injection of the sample into theheated oxidation zone of the furnace or constructed so that theinlet end of the tube is large enough to accommodate a quartzsample boat. The combustion tube must have side arms for

18、theintroduction of oxygen and carrier gas. The oxidation sectionshall be large enough (see Fig. 1) to ensure complete combus-tion of the sample. Fig. 1 depicts conventional combustiontubes. Other configurations are acceptable if precision is notdegraded.5.3 Flow ControlThe apparatus must be equipped

19、 withflow controllers capable of maintaining a constant supply ofoxygen and carrier gas.5.4 Drier TubeThe apparatus must be equipped with amechanism for the removal of water vapor. The oxidationreaction produces water vapor which must be eliminated priorto measurement by the detector. This can be ac

20、complished witha membrane drying tube, or a permeation dryer, that utilizes aselective capillary action for water removal.5.5 UV Fluorescence DetectorA qualitative and quantita-tive detector capable of measuring light emitted from thefluorescence of sulfur dioxide by UV light.5.6 Microlitre SyringeA

21、 microlitre syringe capable ofaccurately delivering 5 to 20-L quantities. The needle shall be50 mm (65 mm) long.5.7 Sample Inlet SystemEither of two types of sampleinlet systems can be used.5.7.1 Direct InjectionA direct injection inlet system mustbe capable of allowing the quantitative delivery of

22、the materialto be analyzed into an inlet carrier stream which directs thesample into the oxidation zone at a controlled and repeatablerate. A syringe drive mechanism which discharges the samplefrom the microlitre syringe at a rate of approximately 1 L/s isrequired. For example, see Fig. 2.5.7.2 Boat

23、 Inlet SystemAn extended combustion tubeprovides a seal to the inlet of the oxidation area and is swept bya carrier gas. The system provides an area to position thesample carrying mechanism (boat) at a retracted positionFIG. 1 Conventional Combustion TubesD 5453 08b2removed from the furnace. The boa

24、t drive mechanism willfully insert the boat into the hottest section of the furnace inlet.The sample boats and combustion tube are constructed ofquartz. The combustion tube provides a cooling jacket for thearea in which the retracted boat rests awaiting sample intro-duction from a microlitre syringe

25、. A drive mechanism whichadvances and withdraws the sample boat into and out of thefurnace at a controlled and repeatable rate is required. Forexample, see Fig. 3.5.8 Refrigerated CirculatorAn adjustable apparatus ca-pable of delivering a coolant material at a constant temperatureas low as 4C could

26、be required when using the boat inletinjection method (optional).5.9 Strip Chart Recorder, (optional).5.10 Balance, with a precision of 60.01 mg (optional).6. Reagents6.1 Purity of ReagentsReagent grade chemicals shall beused in tests. Unless otherwise indicated, it is intended that allreagents shal

27、l conform to the specifications of the Committeeon Analytical Reagents of the American Chemical Society,where such specifications are available.3Other grades may beused, provided it is first ascertained that the reagent is ofsufficiently high purity to permit its use without lessening theaccuracy of

28、 the determination.6.2 Inert GasArgon or helium only, high purity grade(that is, chromatography or zero grade), 99.998 % minimumpurity, moisture 5 ppm w/w maximum.6.3 OxygenHigh purity (that is, chromatography or zerograde), 99.75 % minimum purity, moisture 5 ppm w/w maxi-mum, dried over molecular s

29、ieves. (WarningVigorouslyaccelerates combustion.)6.4 Toluene, Xylenes, Isooctane, reagent grade (other sol-vents similar to those occurring in samples to be analyzed arealso acceptable). Correction for sulfur contribution from sol-vents (solvent blank) used in standard preparation and samplespecimen

30、 dilution is required. Alternatively, use of a solventwith nondetectable level of sulfur contamination relative to thesulphur content in the sample unknown makes the blankcorrection unnecessary. (WarningFlammable solvents.)6.5 Dibenzothiophene, FW184.26, 17.399 % (m/m) S (Note2).6.6 Butyl Sulfide, F

31、W146.29, 21.92 % (m/m) S (Note 2).6.7 Thionaphthene (Benzothiophene), FW134.20, 23.90 %(m/m) S (Note 2).NOTE 2A correction for chemical impurity can be required.6.8 Quartz Wool, or other suitable absorbent material that isstable and capable of withstanding temperatures inside thefurnace (see Note 3)

32、.NOTE 3Materials meeting the requirements in 6.8 provide a moreuniform injection of the sample into the boat by wicking any remaining3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For Suggestions on the testing of reagents notlisted by the Ame

33、rican Chemical Society, see Annual Standards for LaboratoryChemicals, BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.FIG. 2 Direct Inject Syringe DriveD 5453 08b3drops of the sample from the tip of the

34、 syringe needle prior to introductionof the sample into the furnace. Consult instrument manufacturer recom-mendations for further guidance.6.9 Sulfur Stock Solution, 1000 g S/mLPrepare a stocksolution by accurately weighing approximately 0.5748 g ofdibenzothiophene or 0.4562 g of butyl sulfide or 0.

35、4184 g ofthionaphthene into a tared 100 mL volumetric flask. Dilute tovolume with selected solvent. This stock can be further dilutedto desired sulfur concentration (Notes 4-7).NOTE 4Working standards that simulate or match the composition ormatrix of the samples analyzed can reduce test result bias

36、 between directinject and boat sample inlet systems.NOTE 5Working standards should be remixed on a regular basisdepending upon frequency of use and age. Typically, stock solutions havea useful life of about 3 months.NOTE 6Calibration standards can be prepared and diluted on amass/mass basis when res

37、ult calculations are adjusted to accommodatethem.NOTE 7Calibration standards from commercial sources can be used ifchecked for accuracy and if precision is not degraded.6.10 Quality Control (QC) Samples, preferably are portionsof one or more liquid petroleum materials that are stable andrepresentati

38、ve of the samples of interest. These QC samplescan be used to check the validity of the testing process asdescribed in Section 14.7. Hazards7.1 High temperature is employed in this test method. Extracare must be exercised when using flammable materials nearthe oxidative pyrolysis furnace.8. Sampling

39、8.1 Obtain a test unit in accordance with Practice D 4057 orPractice D 4177. To preserve volatile components which are insome samples, do not uncover samples any longer thannecessary. Samples shall be analyzed as soon as possible aftertaking from bulk supplies to prevent loss of sulfur or contami-na

40、tion due to exposure or contact with sample container.(WarningSamples that are collected at temperatures belowroom temperature can undergo expansion and rupture thecontainer. For such samples, do not fill the container to the top;leave sufficient air space above the sample to allow room forexpansion

41、.)8.2 If the test unit is not used immediately, then thoroughlymix in its container prior to taking a test specimen.9. Preparation of Apparatus9.1 Assemble and leak check apparatus according to manu-facturers instructions.FIG. 3 Boat Inlet SystemD 5453 08b49.2 Adjust the apparatus, depending upon th

42、e method ofsample introduction, to meet conditions described in Table 1.9.3 Adjust the instrument sensitivity and baseline stabilityand perform instrument blanking procedures following manu-facturers guidelines.10. Calibration and Standardization10.1 Based on anticipated sulfur concentration, select

43、 one ofthe suggested curves outlined in Table 2. Narrower ranges thanthose indicated may be used, if desired. However, the testmethod precision using narrower ranges than those indicatedhave not been determined. Ensure the standards used forcalibration bracket the concentrations of the samples being

44、analyzed. Carefully prepare a series of calibration standardsaccordingly. Make other volumetric dilutions of the stocksolution to cover the various ranges of operation within thesecalibration curve guidelines. The number of standards used percurve can vary, if equivalent results are obtained.10.2 Fl

45、ush the microlitre syringe several times with thesample prior to analysis. If bubbles are present in the liquidcolumn, flush the syringe and withdraw a new sample.10.3 A sample size recommended for the curve selectedfrom Table 2 must be quantitatively measured prior to injectioninto the combustion t

46、ube or delivery into the sample boat foranalysis (Note 8 and Note 9). There are two alternativetechniques available.NOTE 8Injection of a constant or similar sample size for all materialsanalyzed in a selected operating range promotes consistent combustionconditions.NOTE 9Injection of 10 L of the 100

47、 ng/L standard would establisha calibration point equal to 1000 ng or 1.0 g.10.3.1 The volumetric measurement of the injected materialcan be obtained by filling the syringe to the selected level.Retract the plunger so that air is aspirated and the lower liquidmeniscus falls on the 10 % scale mark an

48、d record the volumeof liquid in the syringe. After injection, again retract theplunger so that the lower liquid meniscus falls on the 10 %scale mark and record the volume of liquid in the syringe. Thedifference between the two volume readings is the volume ofsample injected (Note 10).NOTE 10An autom

49、atic sampling and injection device can be used inplace of the described manual injection procedure.10.3.2 Fill the syringe as described in 10.3.1. Weigh thedevice before and after injection to determine the amount ofsample injected. This procedure can provide greater accuracythan the volume delivery method, provided a balance with aprecision of 60.01 mg is used.10.4 Once the appropriate sample size has been measuredinto the microlitre syringe, promptly and quantitatively deliverthe sample into the apparatus. Again, there are two alternativet