ASTM D5505-2014 Standard Practice for Classifying Emulsified Recycling Agents《再循环乳化剂分类的标准实施规程》.pdf

1、Designation: D5505 06D5505 14Standard Practice forClassifying Emulsified Recycling Agents1This standard is issued under the fixed designation D5505; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice identifies emulsified petroleum products that may be used as recycling agents in recycled mixes. Thesematerials are classified

3、 by viscosity or by low temperature penetration after aging.1.2 This practice addresses emulsified materials designed specifically for use in recycling. The use of emulsified materials forrecycling shall not be limited to this practice. For instance, the emulsified asphalts specified in Specificatio

4、ns D977 and D2397 maybe used.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of

5、 this standard to consult and establish appropriate safety and health practices and determine the applicability ofregulatory limitations prior to use.1.3 This practice addresses emulsified materials designed specifically for use in recycling. The use of emulsified materials forrecycling shall not be

6、 limited to this practice. For instance, the emulsions specified in Specfications D977 and D2397 may be used.2. Referenced Documents2.1 ASTM Standards:2D5 Test Method for Penetration of Bituminous MaterialsD70 Test Method for Density of Semi-Solid Bituminous Materials (Pycnometer Method)D140 Practic

7、e for Sampling Bituminous MaterialsD244 Test Methods and Practices for Emulsified AsphaltsD977 Specification for Emulsified AsphaltD1754 Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)D2007 Test Method for Characteristic Groups in Rubber Extender and Processing O

8、ils and Other Petroleum-Derived Oils by theClay-Gel Absorption Chromatographic MethodD2042 Test Method for Solubility of Asphalt Materials in TrichloroethyleneD2170 Test Method for Kinematic Viscosity of Asphalts (Bitumens)D2397 Specification for Cationic Emulsified AsphaltD2872 Test Method for Effe

9、ct of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)D4124 Test Method for Separation of Asphalt into Four FractionsD6930 Test Method for Settlement and Storage Stability of Emulsified AsphaltsD6933 Test Method for Oversized Particles in Emulsified Asphalts (Sieve Test)D6937 T

10、est Method for Determining Density of Emulsified AsphaltD6997 Test Method for Distillation of Emulsified AsphaltD7402 Practice for Identifying Cationic Emulsified AsphaltsD7496 Test Method for Viscosity of Emulsified Asphalt by Saybolt Furol ViscometerD7553 Test Method for Solubility of Asphalt Mate

11、rials in N-Propyl Bromide1 This practice is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.41 on EmulsifiedAsphalt Specifications.Current edition approved Dec. 1, 2006June 1, 2014. Published December 2006July 2014. Origi

12、nally approved in 1994. Last previous edition approved in 20012006 asD5505 97 (2001).D5505 06. DOI: 10.1520/D5505-06.10.1520/D5505-14.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume infor

13、mation, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately de

14、pict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1

15、9428-2959. United States13. Significance and Use3.1 Recycling of deteriorated asphalt pavements is being used as a routine method of maintenance and rehabilitation. Utilizationof existing materials as the major component of this procedure may yield benefits in quality, economy, and preservation of n

16、aturalresources. Recycling takes many forms; hot, cold, in-situ, central plant and surface. This practice may be used for various recyclingmethods.3.2 This practice describes emulsified recycling (ER) agents as belonging to three groups; ER-1, ER-2, and ER-3 as shown inTable 1. The range of recyclin

17、g methods demands several emulsified recycling agents. The groups should provide adequatefreedom of selection for most recycling methods.3.2.1 ER-1 is a material whose main function is to rejuvenate aged asphalt. The material is a petroleum derivative, and highlycompatible with asphalts. It is class

18、ified by viscosity.3.2.2 ER-2 and ER-3 are materials that combine rejuvenators and asphalt components in one emulsified asphalt. These softresidues are classified by low temperature penetration after aging. They are typically used in recycling where there is an increaseddemand for asphalt as when ne

19、w aggregates are added, or where immediate cohesiveness is desired.TABLE 1 Specifications for Emulsified Recycling AgentsTests TestMethod ER-1 ER-2 ER-3min max min max min maxOn emulsionViscosity, 50C, SFS D244 100 20 450 20 450Sieve, % D6933 0.1 0.1 0.1Storage stability,24 h,%D6930 1.5 1.5 1.5Resid

20、ue, bydistillation, %D6997 65 65 65Dilution reportASpecific gravity D70 report report reportCompatibilityB varies report report reportOn residue from distillationKinematic Viscosity, 60C, mm2/s D2170 50 200Saturates, % D2007 30 30 30Solubility in Tri-chloroethyleneD2042 97.5 97.5 97.5On residue from

21、 distillation after RTFOCPenetration, 4C,50 g, 5 sD5 75 200 5 75RTFO, weightchange, %D2872 4 4 4TABLE 1 Specifications for Emulsified Recycling AgentsTests TestMethod ER-1 ER-2 ER-3min max min max min maxViscosity, 50C, SFS D7496 100 20 450 20 450Sieve, % D6933 0.1 0.1 0.1Storage stability,24 h,%D69

22、30 1.5 1.5 1.5Residue, bydistillation, %D6997 65 65 65Dilution reportASpecific gravity D6937 report report reportCompatibilityB D7402 report report reportTests on residue from distillationKinematic Viscosity, 60C, mm2/s D2170 50 200Saturates, % D4124 30 30 30Solubility, % D2042 orD755397.5 97.5 97.5

23、Tests on residue from distillation and RTFOCPenetration, 4C,50 g, 5 sD5 75 200 5 75RTFO, masschange, %D2872 4 4 4A ER-1 shall be certified for dilution with potable water.B This specification allows a variety of emulsions, including high-float and cationic emulsions. emulsified asphalts. The enginee

24、r should take the steps necessary to keepincompatible materials from co-mingling in tanks or other vessels. It would be prudent to have the chemical nature (float test for high float emulsions, particle charge testfor cationic emulsions, or other tests as necessary) charge nature certified by the su

25、pplier.C RTFO shall be the standard. referee method. When approved by the engineer, the Thin Film Oven Test (Test Method D1754) may be substituted for compliance testing.D5505 1423.3 The choice of ER will be determined by the properties of the asphalt binder in the aged pavement, the methods of recy

26、clingplanned, the amount, if any, of new aggregates, and other design needs.4. Classification4.1 This practice describes emulsified recycling (ER) agents as belonging to three groups; ER-1, ER-2, and ER-3 as shown inTable 1. The range of recycling methods demands several emulsified recycling agents.

27、 The groups should provide adequatefreedom of selection for most recycling methods.4.1.1 ER-1 is a material whose main function is to rejuvenate aged asphalt. The material is a petroleum derivative, and highlycompatible with asphalts. It is classified by viscosity.4.1.2 ER-2 and ER-3 are materials t

28、hat combine rejuvenators and asphalt components in one emulsion. These soft residues areclassified by low temperature penetration after aging. They are typically used in recycling where there is an increased demand forbitumen as when new aggregates are added, or where immediate cohesiveness is desir

29、ed.4.2 The choice of ER will be determined by the consistency of the binder in the aged pavement, the methods of recyclingplanned, the amount, if any, of new aggregates, and other design needs.4. Properties4.1 All emulsified recycling agents shall be homogenous, free flowing at pumping temperature,

30、and shall conform to therequirements of Table 1.4.2 Emulsified recycling agent residue should be combined with aged asphalts and evaluated to determine proper ER selectionand to determine quantity of treatment. Resulting asphalt binder properties shall be judged suitable for the intended use.5. Samp

31、ling5.1 Carry out sampling in accordance with Practice D140.5.2 Store samples in new, clean, airtight sealed containers as specified in Practice D140 at a temperature not less than 4C untiltested.6. Test Methods6.1 The properties of the Emulsified Recycling Agents given in Table 1 shall be determine

32、d in accordance with the followingASTM Test Methods:6.1.1 ViscosityTest Method D7496.6.1.2 SieveTest Method D6933.6.1.3 Storage StabilityTest Method D6930.6.1.4 Residue by DistillationTest Method D6997.6.1.5 Specific GravityTest Method D6937.6.1.6 CompatibilityPractice D7402.6.1.7 Tests on Residue f

33、rom Distillation:6.1.7.1 Kinematic ViscosityTest Method D2170.6.1.7.2 SaturatesTest Method D4124.6.1.7.3 SolubilityTest Method D2042 or D7553.6.1.7.4 RTFO ConditioningTest Method D2872.6.1.7.5 Tests on RTFO Residue:(1) PenetrationTest Method D5.(2) Mass ChangeTest Method D2872.D5505 1437. Keywords7.

34、1 emulsified recycling agent; emulsions;emulsified asphalt; recyclingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of an

35、y such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are in

36、vited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not receive

37、d a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of t

38、his standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 144