ASTM D5539-2013 Standard Specification for Seed Starter Mix《种子初始混合的标准规范》.pdf

1、Designation: D5539 13Standard Specification forSeed Starter Mix1This standard is issued under the fixed designation D5539; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates

2、 the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the material characteristics,physical requirements, and sampling appropriate to the desig-nation of a soil or soil-like material for seed s

3、tarting purposes.This would consist of the duration of germination ending afterthe cotyledon stage (at the opening of the first true leaves).1.2 Seed starter mix may include natural soils and artificialmixtures of natural or artificial materials used for the initialgermination of seeds to the cotyle

4、don stage.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard. Alternate sieve designations in parentheses are asprovided in Specification E11.1.4 This standard does not purport to address all of thesafety concerns, if any, asso

5、ciated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applicabil-ity of regulatory limitations prior to use.1.5 The text of this standard references notes and footnoteswhich provide explanatory material. Thes

6、e notes and footnotes(excluding those in tables and figures) shall not be consideredas requirements of the standard.2. Referenced Documents2.1 ASTM Standards:2C330 Specification for Lightweight Aggregates for Struc-tural ConcreteC331 Specification for Lightweight Aggregates for ConcreteMasonry Units

7、D653 Terminology Relating to Soil, Rock, and ContainedFluidsD2607 Classification of Peats, Mosses, Humus, and RelatedProducts (Withdrawn 1990)3D4531 Test Methods for Bulk Density of Peat and PeatProductsE11 Specification for Woven Wire Test Sieve Cloth and TestSieves3. Terminology3.1 DefinitionsFor

8、definitions of general terms, refer toTerminology D653.4. Material and Manufacture4.1 The success of a seed starter mix is measured in itsability to provide a germinating seed with certain basic needs,that are outlined as follows.Avariety of materials, both naturaland artificial, can be employed to

9、provide the characteristicsthat will fill the need.4.2 FunctionA seed starter media provides a seed (seed-ling) with four basic needs:4.2.1 Aeration to permit an exchange of gases between theemerging roots and the surrounding medium,4.2.2 Adequate seed (seedling) to starter media contact topermit wa

10、ter to flow to the seed and seedling root. Thisfunction also relates to the media having a sufficient amount ofwater retention to maintain the amount of moisture needed forplant use,4.2.3 A surface that does not inhibit emergence. This relatesto the medias ability to resist surface crusting, and4.2.

11、4 A bulk density that does not inhibit root elongationand proliferation.4.3 MaterialWhile one material may be able to provide allof the needs of a seed (seedling), a mixture of varyingpercentage of at least two of these materials has been found inpractice to yield more consistent results over a wide

12、 range ofmanagement practices. Therefore, seed starters are generallymixtures of materials. The following is a list of materials thathave been used as or in seed starter mixes:4.3.1 VermiculiteThis is a natural mineral that has beentreated with heat until it becomes porous. This material has theabil

13、ity to hold a significant amount of water and still allow forexcellent drainage. However, it does not provide for goodseed-media contact.1This specification is under the jurisdiction of ASTM Committee D18 on Soiland Rock and is the direct responsibility of Subcommittee D18.22 on Soil as aMedium for

14、Plant Growth.Current edition approved June 15, 2013. Published July 2013. Originallyapproved in 1994. Last previous edition approved in 2013 as D5539 94 (2013).DOI: 10.1520/D5539-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.o

15、rg. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,

16、100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.3.2 Sphagnum Peat MossThis is a natural accumulationof plant material decayed and decaying under anaerobicconditions, and meeting the specifications outlined in Classi-fication D2607. Industry-wide, this seems to b

17、e the onematerial that has no substitute.4.3.3 PerliteThis is a volcanic ash that looks like smallbeads of plastic. Similar to vermiculite, it holds less water butprovides more seed-media contact.4.3.4 Coarse SandThis is mineral soil material that passesthrough a 2.0-mm (No. 10) sieve but is retaine

18、d on a 425-m(No. 40) sieve. It provides good drainage and maintainsfriability. Sieve designations are reported as outlined in Speci-fication E11.4.3.5 Expanded Shale, Clay, or SlateThese are engineeredmaterials that are structural grade, inert, porous lightweightaggregates with properties meeting th

19、e requirements of Speci-fication C330 and C331. Because of their particle strength,these aggregates do not consolidate after initial compaction andare thus free draining.4.3.6 Peat Humus and Other Peat ProductsThis materialis more highly decomposed than the sphagnum variety. Itmeets the specificatio

20、ns outlined in Classification D2607.While it may be used in the mixture, it tends to compact easily.4.3.7 Composted Organic MaterialsThis material has de-sirable nutrient qualities if the seedling is not to be trans-planted; however, it has the same drawbacks as the peat humus.Other properties of th

21、is material may or may not be desirabledepending on the organic parent material and the manner ofcomposting.4.3.8 Other Organic MaterialsWhile raw organic mattermay be tempting from the standpoint of increased friability, itmay lead to nitrogen depletion and pest (disease and insect)problems. Also,

22、some wood products contain natural andartificial toxins which are lethal to plants. As such, eachmaterial would have to be evaluated on its own merit.4.3.9 Other Inorganic MaterialsThis category includescinders, ashes, and a variety of artificial inert soil-like material.Each of these materials woul

23、d have to be evaluated based on itsability to hold moisture, soluble salt content, resistance tocompaction, and pH.4.4 DensityThe bulk density of the media must be suchthat it does not inhibit plant emergence or root elongation. Abulk density less than 1.3E+03 kg/m3(on an oven dry basis(1.3 g/cm3) h

24、as been found in practice to provide adequateresults. This measurement is made using Test Method D4531for the dry density of the media.4.5 pHThe optimum pH for a seed starter media varies bythe species of the plant being grown. Thus, a specific optimumrange of pH is not appropriate for this specific

25、ation. However,the pH must not be extremely acidic or basic.4.6 Soluble SaltsThe concentration of soluble salts mustbe such that it will result in a conductivity less than 0.35 S/m(3.5 mmhos).4Also the portion of the concentration of saltsattributable to sodium (Na) or chloride (Cl) must not exceed1

26、0 % of the total salt concentration. Conductivity measure-ments are made by Method 10-3.3 in Agronomy No. 9, Part 2.54.7 NutrientsSince seeds contain their own food supply,the nutrient content of the growth media is not an issue. Overthe germination period covered by this specification, seeds willsp

27、rout and form healthy seedlings in a mixture totally devoid ofnutrients. However, low concentrations of nutrients in themixture pose no drawbacks in the stage of seedling growthcovered by this specification and may yield certain advantages.Nutrients in a starter mix also allow a seedling to remain i

28、n thesame media further into its life, reducing the need for trans-planting. Since nutrients pose no harm and are beneficial to theplant in later seedling growth stages, the issue of plant nutrientsin the seed starter mix is left to the individual manufacturer oruser.4.8 SanitationGerminating seedli

29、ngs are extremely vul-nerable to insects and diseases. To protect the seedling throughthis period, handling of the media must be as sanitary aspractical to reduce the amount of harmful insect eggs andlarvae, nematodes, viruses, and microbes. Further sterilizationtechniques can be used, if desired.5.

30、 Rejection and Rehearing5.1 The mixture cannot be labeled as a seed starter mix if itfails to conform to any of the requirements of this specification.5.2 Material that fails to conform to the requirements of thisspecification may be rejected. Rejection should be reported tothe producer or supplier

31、promptly and in writing. In case ofdissatisfaction with the results of tests, the producer or suppliermay make claim for a rehearing.6. Packaging and Package Marking6.1 Unless otherwise specified in the purchase contract orby the purchaser, the prepared mix is packaged in variousquantities. Bales an

32、d bulk sales are also allowed.6.2 Unless otherwise specified in the purchase contract orby the purchaser, the name of the manufacturer, name ofproduct, net volume, and a statement denoting compliance withthis specification shall be legibly marked on each package.7. Keywords7.1 horticulture; peat; se

33、ed starter; seedlings; soil4A conductivity of 0.35 S/m (3.5 mmhos) is safe for most plants; however, somesalt sensitive plant species can be damaged by a conductivity of 0.35 S/m.5“Methods of SoilAnalysis,” Method 10-3.3, Agronomy No. 9, Part 2,AmericanSociety of Agronomy, Madison, WI, 1982.D5539 13

34、2SUMMARY OF CHANGESCommittee D18 has identified the location of selected changes to this standard since the last issue (D5539 94(2013) that may impact the use of this standard. (Approved June 15, 2013.)(1) Updated Section 1.(2) Updated Section 3.(3) Updated Section 5.ASTM International takes no posi

35、tion respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibili

36、ty.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to AST

37、M International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address

38、shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5539 133