ASTM D5883-1996(2008) 866 Standard Guide for Use of Rotary Kiln Produced Expanded Shale Clay or Slate (ESCS) as a Mineral Amendment in Topsoil Used for Landscaping and Related Purp.pdf

1、Designation: D 5883 96 (Reapproved 2008)Standard Guide forUse of Rotary Kiln Produced Expanded Shale, Clay or Slate(ESCS) as a Mineral Amendment in Topsoil Used forLandscaping and Related Purposes1This standard is issued under the fixed designation D 5883; the number immediately following the design

2、ation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide covers the material

3、characteristics, physicalrequirements, and sampling appropriate for the designation ofthe material as a mineral amendment.1.2 The presence in the topsoil of the correct nutrient andpH level is necessary for healthy plant growth. This guide doesnot, however, cover a determination of the nutrients, no

4、r theiravailability.2NOTE 1The nutrient content of topsoil is important and the chemicalsusually evaluated are nitrogen, phosphate, and potassium. Nutrient defi-ciencies may be corrected by using fertilizers. Excess soluble salts shouldbe examined as to their desirability. The acidity or alkalinity

5、of the soil isalso important. Excess acidity may be corrected by the application of limedust. Excess alkalinity may be corrected by the application of sulfur orother suitable acidifying compounds. The latter item, in addition tolowering pH, also could be considered as an aggregate when consideringth

6、e particle size distribution.1.3 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of t

7、his standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.5 This guide offers an organized collection of informationor a series of options and does not recommend a specificcourse of action. This document cannot replac

8、e education orexperience and should be used in conjunction with professionaljudgment. Not all aspects of this guide may be applicable in allcircumstances. This ASTM standard is not intended to repre-sent or replace the standard of care by which the adequacy ofa given professional service must be jud

9、ged, nor should thisdocument be applied without consideration of a projects manyunique aspects. The word “Standard” in the title of thisdocument means only that the document has been approvedthrough the ASTM consensus process.2. Referenced Documents2.1 ASTM Standards:3C 29/C 29M Test Method for Bulk

10、 Density (“Unit Weight”)and Voids in AggregateC 566 Test Method for Total Evaporable Moisture Contentof Aggregate by DryingD75 Practice for Sampling AggregatesD 653 Terminology Relating to Soil, Rock, and ContainedFluidsD 1140 Test Methods for Amount of Material in Soils Finerthan No. 200 (75-m) Sie

11、veD 4972 Test Method for pH of SoilsD 5268 Specification for Topsoil Used for LandscapingPurposesE11 Specification for Wire Cloth and Sieves for TestingPurposes3. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication, refer to Terminology D 653.3.2 Definitions of Terms Speci

12、fic to This Standard:3.2.1 amendment, physicalany substance, such as sand,calcined clay, peat, or sawdust, added to the soil to alter itsphysical properties.3.2.2 slit trench draina narrow trench (usually 5 to 10centimeters wide) back-filled to the surface with a material,such as sand, gravel, or cr

13、ushed rock, to facilitate surface orsubstance drainage.3.2.3 soil amendment (physical), nany substance, such assand, calcined clay, shale or slate, peat or sandust, added to thesoil to alter its physical properties.1This guide is under the jurisdiction ofASTM Committee D18 on Soil and Rockand is the

14、 direct responsibility of Subcommittee D18.22 on Soil as a Medium forPlant Growth.Current edition approved Jan. 1, 2008. Published February 2008. Originallyapproved in 1995. Last previous edition approved in 2002 as D 5883 96 (2002).2Nutrient testing procedures are found in the state Agricultural Ex

15、perimentStation recommendations from the state within which the landscape is located,“Methods of Soil Analysis” Editor-in-Chief: C. A. Black, Agronomy No. 9, Vol 2,American Society of Agronomy, Inc., Madison, WI, and Hesse, P.R., A Textbook ofSoil Chemical Analysis, Chemical Publishing Co., New York

16、, NY 1972.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Driv

17、e, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.2.4 soil modification, nalteration of soil characteristicsby addition of physical amendments: commonly used toimprove physical conditions of soils.3.2.5 soil probea soil sampling tool having a hollowcylinder with a cutting edge at the

18、 lower end.3.2.6 topdressing, na prepared soil mix added to a turfsurface and usually physically worked in by matting, raking,irrigating, or all three, to a smooth surface.3.2.7 topsoil, nusually the original surface layer of grass-land or cultivated land. Topsoil does not generally include soilfrom

19、 peatlands or other special areas, such as land disturbed byindustrial activity. Topsoil is usually a darker shade of brown,gray, or red than the subsoil that lies immediately beneath it,because it contains organic matter intimately mixed with themineral matter. Topsoil tends to be more friable and

20、perviousthan inorganic soils.4. Significance and Use4.1 When physically evaluating a soil, relative to its suit-ability to support plant growth (primarily grasses), tests mustbe performed to determine the presence and amount of solidmatter (organic and inorganic) compatibility that can determinepote

21、ntial air-void content and water-holding ability, and finally,deleterious materials.4.2 Typical general ranges of soil content for suitabletopsoils are presented in Specification D 5268. It should berecognized, however, that in some geographic regions, concur-rence with the values in the referenced

22、table would be difficult.In such situations, locally acceptable specifications need to bedeveloped.5. Function and Material5.1 FunctionThe potential/success of a topsoil amend-ment is measured/determined by its ability to provide some orall of the desired properties/characteristics of the topsoil th

23、atare absent in the unamended topsoil or soil. Soils consistessentially of three space-occupying components: water, airvoids, and solid particulate matter. The third component can befurther divided into two sub-components: organic matter, suchas peat, muck or other decayed matter: and inorganic mine

24、ralmatter, such as clay, silt and sand. ESCS falls into the lattergroup of the third component sub-component group, as a bettersubstitute for sand.5.2 MaterialESCS, is a rotary kiln produced vesicularamorphous silicate particulate material. It is a highly porous,low density material with an apparent

25、 specific gravity ofapproximately 0.8 to 2.4, and a dry/loose unit weight ofapproximately 35 to 70 lb/ft3, (561 to 1121 kg/m3). Thepre-sized raw shale, clay or slate used to produce ESCS is firedin the kiln at a temperature between 1800F (982C) and2200F (1205C). As it exits the kiln the material is

26、sterile,inert, and ceramic. Some crushing may be performed tofacilitate final sizing in a screening system. ESCS in generallyneutral in pH although the pH can vary somewhat dependingon the raw material and the fuel in the kiln. Density, or looseunit weight, is determined by Test Method C 29/C 29M. T

27、heabsorption may be determined by Test Method C 566 aftersoaking the sample a sufficient period of time, usually 3 to 7days, depending on the source and the grading of the material.The particle distribution may be determined with appropriatesieves as stated in Specification E11. The ESCS may besampl

28、ed in accordance with Practice D75.6. Application6.1 ESCS is generally used in horticultural topsoil applica-tions as a substitute for the sand sub-component of soils solidcomponent (see Specification D 5268, Table 1). The mainadjustment that needs to be made is a correction for the weightand volume

29、 relationship of ESCS fines, that is, the minus No.4 (4.75 mm) sieve size to a similar size of sand. The oven-dryor saturated surface dry/loose unit weight tests (see TestMethod C 29/C 29M) can be performed to establish theweight-volume relationship. Typically, a loose cubic foot ofESCS fines will w

30、eigh approximately from 35 lb/ft3(560 kg/m3to 70 lb/ft3) (1120 kg/m3) depending on the source. Absorptionof ESCS varies with the source, but is usually from approxi-mately 18 % to 35 % of the oven-dry loose unit weight. Severalblends of topsoil using ESCS with or in place of the sandshould be prepar

31、ed and evaluated with regard to potential foraeration, moisture retention, resistance to compaction, and theother items covered in Specification D 5268.NOTE 2ESCS was originally patented as Haydite in 1918. It has beenused in horticultural research as well as in private and commercial plant(and gras

32、s) soil modification management in the United States and Europesince the early 1920s. It is used extensively in hydroponics, as well.7. Keywords7.1 horticulture; landscaping; mineral amendment Haydite;soil; soil amendment; modification; topsoilASTM International takes no position respecting the vali

33、dity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subj

34、ect to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquar

35、ters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standar

36、d is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 5883 96 (2008)2