1、Designation: D5909 96a (Reapproved 2011)Standard Test Method forDrying Time of Oxidative-Drying Printing Inks by SqualeneResistance1This standard is issued under the fixed designation D5909; the number immediately following the designation indicates the year oforiginal adoption or, in the case of re
2、vision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the procedure for determiningthe drying time of oxidative-drying printing
3、inks (also referredto as “sheetfed inks”) by squalene resistance of printed inkfilms.1.2 This test method is applicable to all paste inks that dryprimarily by oxidation regardless of the substrate on whichthey are printed. With appropriate changes in the test fluid, itmay also be used with paste ink
4、s that dry by other mechanisms,such as heatset or ultraviolet light.1.3 This test method utilizes a modified rub tester and isintended to serve as a “referee” procedure when laboratories,using less rigorous test procedures (see Appendix X1), cannotagree on their results.1.4 The values stated in SI u
5、nits are to be regarded as thestandard. The values given in parentheses are for informationonly.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health p
6、ractices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D4332 Practice for Conditioning Containers, Packages, orPackaging Components for TestingD5264 Practice for Abrasion Resistance of Printed Materi-als by the Sutherland Rub Teste
7、r3. Terminology3.1 Definition of Terms Specific to This Test Method:3.1.1 blanket, na composite structure, normally a rubber-like layer supported by one or more fabric or foam layers, orboth.3.1.2 squalene oil, nan organic liquid (C30H50unsatu-rated aliphatic hydrocarbon) that imitates the action of
8、 skin oil.3.1.3 DiscussionSqualene dissolves vehicle componentsin a typical oxidative-drying ink system but not when fullypolymerized.4. Summary of Test Method4.1 The test print is affixed to the base of the rub tester. Theremovable one-half pound weight of the instrument is fittedwith a piece of ru
9、bber blanket and covered with an absorbenttowel to which a small amount of squalene oil has been added.The weighted, oil-impregnated towel is allowed to rub backand forth over the test print for a prescribed number of cycles.4.2 The receptor towel is examined for evidence of inktransfer from the pri
10、nt. Results may be related qualitatively toan agreed upon standard, or, the intensity of the stain can bemeasured quantitatively with a colorimeter, spectrophotometer,or other reflectance type device.5. Significance and Use5.1 Inadequate setting or drying of sheetfed inks, or both,can cause blocking
11、 of stacked prints with subsequent loss ofproduct. “Setting” of an ink refers to the rapid rise in viscosityof the printed ink film, sometimes accompanied by surfacedrying, that prevents transference of the undried ink film toadjacent surfaces under light pressure. “Setting” is a propertyof the ink-
12、substrate combination. Inadequate drying may bedue to several factors, but the primary causes are: (1) omissionof metallic driers from the ink, improper ink formulation (2)unusual ink-substrate interactions, and (3) use of a fountainsolution that is too acidic. If the test prints are made on astanda
13、rd laboratory proof press, where there is no applicationof fountain solution, then only the first three possible causescan be evaluated. If the prints have been made on a commercialproduction printing press or some other acceptable means ofintroducing the fountain solution into the ink agreed upon,
14、thenthe effect of fountain solution can be determined. It will oftenbe necessary to run several tests to isolate the specific cause ofa drying problem.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct respons
15、ibility ofSubcommittee D01.56 on Printing Inks.Current edition approved June 1, 2011. Published June 2011. Originallyapproved in 1996. Last previous edition approved in 2006 as D5909 96a (2006).DOI: 10.1520/D5909-96AR11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact
16、ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 This test method is su
17、itable for most combinations ofoxidative drying inks and substrates. Because this test methodrelies on a visual assessment of the extent of drying, very lightcolors and clear varnishes may present difficulties in quantify-ing the extent of drying. In such cases, the supplier and thecustomer should a
18、gree upon an alternative method of assessingthe drying properties of the ink.6. Apparatus6.1 Rub Tester, conforming to Test Method D5264 butequipped with a special one-half pound weight and modified asin Section 9.6.2 Laboratory Printing Apparatus, capable of preparingtest prints from a blanket or r
19、ubber covered-printing disk (thatis, by the dry offset mode). The minimum print size is about 47by 115 mm.6.3 Reflection Densitometer, for use in controlling the inkdensity of the printed specimens.6.4 Spectrophotometer (Optional), for measuring the reflec-tance of receptor toweling.7. Materials7.1
20、Soft Toweling, cut to fit the sub tester receptor block 50by 140 mm.7.2 Squalene Oil,37.3 Rubber Blanket,4preferably having an adhesive or“sticky” backing, cut to 38 by 38 mm.7.4 Substrate, such as paper, paperboard or other as agreedupon between the supplier and the customer. The substrateshould be
21、 cut to a size appropriate to the printing apparatus(6.2).7.5 Reference Standards (optional), such as wet productionor laboratory prints of inks and substrates having known ordesired drying properties.8. Test Specimen and Conditioning8.1 Set the rub tester on a sturdy bench, preferably in a roomcond
22、itioned at 23 6 1C (73.4 6 2F) and 50 6 2 % relativehumidity, as described in Practice D4332.9. Preparation of the Rub Tester9.1 Remove the one-pound weight of the rub tester andreplace with the special half-pound weight. Affix the 38-mmsquare rubber blanket (7.3) to the center portion of the weight
23、.9.2 Remove the rubber pad from the lower surface of theinstrument. Replace with a glass plate of comparable size.9.3 In order to facilitate proper placement of the testspecimen, determine where the center stroke occurs and scribe,or otherwise indicate, a line on the glass plate. Similarly, scribeli
24、nes to facilitate placement of the specimen in the left-to-rightdirection.10. Procedure10.1 Using the manufacturers instructions, ink up thelaboratory printing apparatus and pull a print on the agreedupon substrate. Measure the optical density. If not within60.05 of the desired value, discard and ap
25、ply more or less inkto the print maker. Prepare a sufficient number of prints so that,after cutting, there will be a minimum of six specimens eachabout 47 by 115 mm. Record the time of printing on eachspecimen.NOTE 1The wide rubber disk of the bench type print tester producesa printed strip 47-mm wi
26、de and 230-mm long; by cutting in halfcross-wise, two 47 by 115 mm specimens per print are obtained. The plateof a common flat-bed proof press is 102 by 153 mm and also gives two 47by 115 mm specimens per print. In each case, three prints are needed toprovide six test specimens.10.2 A few minutes be
27、fore an hour has elapsed, clamp asingle thickness piece of toweling to the receptor block of therub tester. With a pipet or eye dropper, place five drops ofsqualene oil on the towel in the region that lies over the rubberblanket. Using the thumb, work the oil into the toweling so thatit is fully sat
28、urated, but not dripping in the region over therubber blanket.10.3 Center a specimen on the glass plate and tape down.One hour after the print was made, place the weight in itslocation on top of the specimen and turn the instrument on.Conduct the test for 15 strokes (a stroke consists of one backand
29、 forth cycle).10.4 Remove the specimen and receptor towel. Carefullyblot off any excess oil. Mark the number of hours that haveelapsed between the time of printing and that of rub testing.10.5 If inspection (11.1) indicates the print is not dry, set theprint and receptor towel aside, and repeat 10.2
30、 to 10.4 onanother print specimen at 1-h (or other agreed upon) intervalsafter printing. If the ink has not completely dried at the end of6 h, then the time interval must be extended by starting from10.1 and running the tests at longer intervals or longer times.11. Evaluation11.1 Visually inspect th
31、e print for evidence of adverseeffects and the receptor towel for evidence of ink transfer.11.2 (Optional) Set the spectrophotometer to the followingcondition: Illuminant C, large aperture, 2 observer. Determinethe reflectance of the receptor towels as a function of time,using an oil-soaked towel as
32、 the 100 % reflectance standard.Plot results in the form of L* versus time, noting on the graphthe points at which visual drying (11.1) occurred. Drying canbe considered complete when L* = 80 %.12. Report12.1 Report the time in hours at which there is no visibleeffect on the test print or the L* val
33、ue of the receptor towelreaches 80 %.12.2 If a reference standard was used, report whether thedrying time of the test sample was shorter, equal to, or longerthan the standard.13. Precision and Bias513.1 PrecisionAn interlaboratory study of this testmethod was conducted in which 5 laboratories tested
34、 3 inks3Available from chemical supply houses.4Suitable rubber blanket is available from local graphic art supply houses.5Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D01-1097.D5909 96a (2011)2ranging in drying time from about
35、 2 to 5 h. The overallstandard deviation was 0.74 h. Based on this result, thefollowing criteria should be used for judging the acceptabilityof results at the 95 % confidence level.13.1.1 RepeatabilityRepeatability cannot be determinedbecause the tests were not replicated.13.1.2 ReproducibilityTwo r
36、esults obtained by operatorsin different laboratories should be considered suspect if theydiffer by more than 2 h.13.2 BiasBias cannot be determined because there are nostandard materials.14. Keywords14.1 drying; oxidative drying; paper; paperboard; printingink; squalene resistanceAPPENDIX(Nonmandat
37、ory Information)X1. MANUAL METHODX1.1 The generally accepted industrial practice for deter-mining “drying” of inks involves wiping prints, preparedsimilarly to the procedure described in this test method, withcotton swabs or balls that have been impregnated with anappropriate fluid at various times.
38、X1.2 As part of the interlaboratory round-robin conductedin 13.1, four of the participating laboratories concurrentlymeasured the drying time of the same ink/paper combinationusing the procedure outlined in X1.1. Test results obtained bythe various operators differed by as much as 5 h, well beyondth
39、e 2 h cited in 13.1.2.X1.3 The manual procedure is very operator sensitive dueprimarily to the variation in applied pressure when wiping theprint. The present method, involving a rub tester, serves tostandardize the applied force and wiping action.ASTM International takes no position respecting the
40、validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is
41、subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Head
42、quarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This sta
43、ndard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5909 96a (2011)3
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1