ASTM D6015-2000(2005) Standard Test Method for Static Water Absorption of Leather《测定皮革静态吸水性的标准试验方法》.pdf

1、Designation: D 6015 00 (Reapproved 2005)Standard Test Method forStatic Water Absorption of Leather1This standard is issued under the fixed designation D 6015; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisio

2、n. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This test method covers the determination of the

3、 amountof water absorbed by leather at 23 6 2C by immersion understatic conditions. It may be used on all types of leather. Thistest method does not apply to wet blue.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of

4、the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:D 1517 Terminology Relating to Leather2D 1610 Practice for Conditioning Leather23. Terminology3.1 For defi

5、nitions of leather terms used in this test methodrefer to Terminology D 1517.4. Summary of Test Method4.1 In this test method the amount of water absorbed by aleather specimen is measured at room temperature with allsurfaces exposed to water.5. Significance and Use5.1 This test method is used to det

6、ermine compliance withspecifications for water absorption of upper leather. Thesignificance of the test method is limited by the static condi-tions employed, and the results do not reflect the waterabsorption under dynamic conditions of flexing.6. Apparatus6.1 Beaker, 1000 mL.6.2 Balance, sensitive

7、to 0.01 g.6.3 Blotting Paper.7. Test Specimen7.1 The test specimen shall be a square of leather approxi-mately 4 by 4 in. (102 by 102 mm).7.2 Unless otherwise specified in the detail specification,one specimen from each test unit of sample shall be tested.7.3 Prior to testing, the specimen shall be

8、conditionedaccording to Practice D 1610.8. Procedure8.1 Weigh the specimen to the nearest 0.01 g and record themass as W1.8.2 One to three specimens shall be completely immersed ina 1000 mL beaker of distilled water at 23C 6 2C. Thisshould be done in such a manner that the surface of thespecimens do

9、 not touch each other.8.3 After 1 h 61 min immersion, the specimens shall beremoved from the beaker and the surface water from eachremoved by lightly blotting the specimen with blotting paperprior to weighing.8.4 The specimen shall then be weighed immediately andthe mass recorded as W2.9. Calculatio

10、n9.1 The amount of water absorbed by each specimen shallbe calculated as follows:Water absorbed, % 5 W22 W1!/W1# 3 100 (1)where:W1= weight of the original specimen, grams, andW2= weight of the specimen after water immersion,grams.10. Report10.1 The amount of water absorbed by the specimen shallbe re

11、ported to the nearest 0.01 %.1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.03 on Footwear.Current edition approved Sept. 1, 2005. Published September 2005. Originallyapproved in 1996. Last previous edition approved in

12、 2001 as D 6015 - 00(2001).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100

13、 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.11. Precision and Bias11.1 This test method is adopted from the procedures of theFederal Government where it has long been in use. It wasapproved for publication before the inclusion of precision andbias statements was

14、mandated. The original interlaboratory testdata is no longer available. The user is cautioned to verify byuse of reference materials, if available, that the precision andbias of this test method is adequate for contemplated use.12. Keywords12.1 leather; static; water absorptionASTM International tak

15、es no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own re

16、sponsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addres

17、sed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at th

18、e address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 6015 00 (2005)2