ASTM D6506 D6506M-2001(2018)e1 5625 Standard Specification for Asphalt Based Protection Board for Below-Grade Waterproofing《低等级防水用沥青基防护板标准规范》.pdf

1、Designation: D6506/D6506M 01 (Reapproved 2018)1Standard Specification forAsphalt Based Protection Board for Below-GradeWaterproofing1This standard is issued under the fixed designation D6506/D6506M; the number immediately following the designation indicates theyear of original adoption or, in the ca

2、se of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEUnits information was editorially corrected in January 2018.1. Scope1.1 This specification covers

3、 an asphalt based protectionboard used for protecting the integrity of below grade or belowwearing surface waterproofing. The protection board protectsthe waterproofing system from backfill, surfacing, constructionactivities, and weathering conditions prior to backfilling orapplying surfacing.1.2 Th

4、e values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the st

5、andard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior

6、 to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBar

7、riers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D545 Test Methods for Preformed Expansion Joint Fillersfor Concrete Construction (Nonextruding and ResilientTypes)D994/D994M Specification for Preformed Expansion JointFiller for Concrete (Bituminous Type)D5147/D5147M Test Met

8、hods for Sampling and TestingModified Bituminous Sheet MaterialE154/E154M Test Methods for Water Vapor Retarders Usedin Contact with Earth Under Concrete Slabs, on Walls, oras Ground Cover3. Classification3.1 Two Classes of Product are Covered in This Specifica-tion:3.1.1 Class A, is made with aspha

9、lt saturated organic felt onthe bottom and a coated or saturated non-woven glass felt ontop.3.1.2 Class B, is made with glass fabrics both top andbottom.3.1.3 Classes A and B, each include three thicknesses ofboard. If desired, one side of each of these classes may becovered with a thin plastic anti

10、stick sheet.4. Materials and Manufacture4.1 The protection board shall be comprised of layers ofasphalt and reinforcing mat. One surface of the board will beuniformly coated with a bituminous material for limitedweather protection.4.2 The length and width measurements shall be as specifiedby the man

11、ufacturer. The tolerances of these dimensions(length and width) shall be 66mm14 in.4.3 The surfaces of the protection board shall be uniformand free from defects such as cracks and indentations. Theedges shall be uniform.5. Sampling5.1 Each sample shall consist of sufficient material toprovide at le

12、ast five specimens for the tests listed in Section 7.One representative sample shall be selected for each shipmentof 10 000 ft2or fraction thereof.6. Physical Requirements6.1 Nominal thicknesses of protection board are as follows:6.1.1 Type 1, board is116 in.1This specification is under the jurisdic

13、tion of ASTM Committee D08 onRoofing and Waterproofing and is the direct responsibility of Subcommittee D08.22on Waterproofing and Dampproofing Systems.Current edition approved Jan. 1, 2018. Published January 2018. Originallyapproved in 2001. Last previous edition approved in 2009 as D6506 01 (2009)

14、.DOI: 10.1520/D6506_D6506M-01R18E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM Internatio

15、nal, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guide

16、s and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16.1.2 Type 2, board is18 in.6.1.3 Type 3, board is14 in.6.2 Class A protection board shall conform to the require-ments in Table 1.6.3 Class B protection board shall conform to the require-ments

17、 in Table 2.7. Test Methods7.1 ThicknessDetermine the thickness of the specimenusing vernier calipers in accordance with Test Methods D5147/D5147M, Section 5.7.2 Puncture StrengthDetermine in accordance with TestMethods E154/E154M, Section 10.7.3 Water AbsorptionDetermine in accordance withSpecifica

18、tion D994/D994M, 8.3.7.4 Asphalt ContentDetermine according to Test MethodsD545, 7.5.7.5 Resistance to DecayDetermine according to TestMethods E154/E154M, Section 13.8. Keywords8.1 protection board; waterproofingASTM International takes no position respecting the validity of any patent rights assert

19、ed in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by t

20、he responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive

21、 careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Interna

22、tional, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through

23、the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Class A Protection Board RequirementsType 1 Type 2 Type 3Puncture Strength 222 N 50 lbf minimum 312

24、 N 70 lbf minimum 365 N 82 lbf minimumThickness 1.3 to 1.8 mm 0.050 to 0.070 in. 2.4 to 3.9 mm 0.095 to 0.155 in. 5.6 to 7.1 mm 0.220 to 0.280 in.Water Absorption 10.0 % maximum 10.0 % maximum 10.0 % maximumAsphalt, % by weight 65 % minimum 65 % minimum 65 % minimumResistance to Decay Meets puncture

25、 requirements aftercompletion of testMeets puncture requirements aftercompletion of testMeets puncture requirementsafter completion of testTABLE 2 Class B Protection Board RequirementsType 1 Type 2 Type 3Puncture Strength 222 N 50 lbf minimum 312 N 70 lbf minimum 365 N 82 lbf minimumThickness 1.3 to

26、 1.8 mm 0.050 to 0.070 in. 2.4 to 3.9 mm 0.095 to 0.155 in. 5.6 to 7.1 mm 0.220 to 0.280 in.Water Absorption 10.0 % maximum 10.0 % maximum 10.0 % maximumAsphalt, % by weight 40 % minimum 40 % minimum 40 % minimumResistance to Decay Meets puncture requirements aftercompletion of testMeets puncture requirements aftercompletion of testMeets puncture requirementsafter completion of testD6506/D6506M 01 (2018)12