ASTM D6633-2018 red 5000 Standard Practice for Basic Functional Stability of a Mechanical Pump Dispenser.pdf

1、Designation: D6633 05 (Reapproved 2010)D6633 18Standard Test Method Practice forBasic Functional Stability of a Mechanical Pump Dispenser1This standard is issued under the fixed designation D6633; the number immediately following the designation indicates the year oforiginal adoption or, in the case

2、 of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method practice covers the determination of the basic functional stability of a me

3、chanical pump dispenser with aproduct.1.2 This test method practice covers accelerated usage evaluations of mechanical pump dispensers (spray or flow types) witha product.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibili

4、tyof the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine theapplicability of regulatory limitations prior to use.Specific precautions are given in Section 5.1.4 This international standard was developed in accordance with internat

5、ionally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D2063 Test

6、 Methods for Measurement of Torque Retention for Packages with Continuous Thread ClosuresD3890 Practice for Number of Strokes to Prime a Mechanical Pump DispenserD4336 Practice for Determination of the Output Per Stroke of a Mechanical Pump DispenserE122 Practice for Calculating Sample Size to Estim

7、ate, With Specified Precision, the Average for a Characteristic of a Lot orProcess3. Significance and Use3.1 This test method practice is used for determining the accelerated usage of a mechanical pump dispenser for consumer usage.4. Apparatus4.1 Containers, that will allow the mechanical pump dispe

8、nser to be affixed to them (Note 1) and also be capable of containingproduct for a period of time at various environmental conditions (Note 2).NOTE 1If possible, the actual container to be marketed should be used.4.2 Product, a sufficient amount to fill the number of containers in accordance with 4.

9、1, reference 10.2.4.3 Balance, with direct reading to 0.01 g. Top loading or analytical style is recommended.4.4 Environments, where the mechanical pump dispenser and product will be kept during the test period.4.4.1 Ambient Area, maintained at 23 6 3C (73 6 5.4F).4.4.2 Oven (45C) , maintained at 45

10、 6 3C (113 6 5.4F).NOTE 2The oven temperature can be changed according to product formulation. If different temperatures are used, this should be noted in the testreport discussed in 11.4.4.3 Cycle Chamber, optional, alternating 5 to 50C (41 to 122F) every 24 h.1 This test method practice is under t

11、he jurisdiction ofASTM Committee F02 on FlexiblePrimary Barrier Packaging and is the direct responsibility of Subcommittee F02.30on Mechanical Pump Dispensers.Current edition approved Oct. 1, 2010May 1, 2018. Published March 2011June 2018. Originally approved in 2001. Last previous edition approved

12、in 20052010 asD6633 05.D6633 05(2010). DOI: 10.1520/D6633-05R10.10.1520/D6633-18.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page

13、on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that use

14、rs consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.5 Oven-Safe Tray, with abs

15、orbent paper towels laid in the tray.4.6 Food Coloring or Dye, optional.5. Precautions5.1 Appropriate handling considerations should be given to flammable, toxic, caustic, or other potentially hazardous materialused. When testing at any temperature, safety should be the number one consideration and

16、special attention should be used on theflash points of the products tested.6. Sampling6.1 Based upon the desired precision, sampling shall be performed in accordance with Practice E122.6.2 In the absence of any special sampling plan, performance shall be based on not less than the number of represen

17、tativespecimens exposed to any of the environmental conditions as specified in Section 9.7. Test Specimen7.1 Test specimens shall be clean, dry and previously unused mechanical pump dispensers.8. Conditioning8.1 If possible, condition the test specimens at 23 6 3C (73 6 5.4F) for not less than 4 h.

18、If the test specimens are notconditioned at the recommended temperature, this should be noted in the test report discussed in 11.8.2 Test pumps should be tested no sooner than 24 h after assembly when possible. If pumps are not conditioned at therecommended time, this should be noted in the test rep

19、ort discussed in 11.9. Test Specimen Preparation9.1 Prepare a minimum of 12 mechanical pump dispensers with product and containers to be used for accelerated usageevaluation.9.1.1 Affix the mechanical pump dispensers to containers at the minimum recommended torque load in accordance with TestMethod

20、D2063.9.1.2 Label all of the assembled units with the product name, any safety hazards for the product, name of the techniciancompleting the test, and the test number or means of identifying the test along with the following:9.1.2.1 Minimum 3 units labeled, “Upright, Ambient.”9.1.2.2 Minimum 3 units

21、 labeled, “Upright, Oven 45C.”9.1.2.3 Optional: Minimum 3 units labeled, “Upright, Cycle Chamber.”9.1.2.4 Minimum 3 units labeled “On-Side, Ambient.”9.1.2.5 Minimum 3 units labeled, “On-Side, Oven 45C).”9.1.2.6 Optional: Minimum 3 units labeled “On-Side, Cycle Chamber.”10. Procedure10.1 Test each me

22、chanical pump dispenser for strokes to prime in accordance with Test Method D3890. Report the findings in11.1.10.2 Test each mechanical pump dispenser for output per stroke in accordance with Test Methods D4336. Visually inspect thespray or flow of the product to ensure that no obstructions are pres

23、ent.10.3 Place all of the test specimens as prepared in 9.1 in their respective environments as indicated by the appropriate label oneach unit. Except for trigger sprayers, place specimens labeled “On-Side” with the orifice facing down. Trigger sprayers may havethe orifice oriented to the side while

24、 in the “on-side” position. If the mechanical pump dispensers use a protective hood or overcap,these test specimens should be stored with their protective devices in place. If the mechanical pump dispensers have a lockingfeature, these test specimens should be stored in the locked position during st

25、orage and unlocked for testing.10.4 Except for trigger sprayers, remove all of the test samples from their respective environments three times per week,(preferably Monday, Wednesday, and Friday), over a four week period for a total of 12 test days.10.5 For trigger sprayers, remove all of the test sp

26、ecimens from their respective environments once every two weeks for aduration of 12 weeks for a total of 7 test days.10.6 Allow the temperature of the test specimens to equilibrate (generally 4 to 6 h) to ambient temperature prior to the actualevaluations.10.7 Evaluate the primed mechanical pump dis

27、pensers for each of the following parameters:10.7.1 LeakageVisually inspect for the presence of product on the outside of either the mechanical pump dispenser or thecontainer. If any test specimen exhibits a high degree of leakage, discontinue any additional testing with that particular mechanicalpu

28、mp dispenser and report the findings in 11.1.D6633 18210.7.2 Retention of PrimeFully stroke each mechanical pump dispenser to determine if the mechanical pump dispenser hasretained its prime. If any test specimen has lost prime and it is unable to be reprimed, then discontinue any additional testing

29、 withthat particular mechanical pump dispenser and report the findings in 11.1.NOTE 3If the mechanical pump dispenser fails to re-prime as a result of a clog, then try cleaning in accordance with 10.7.3 before concluding thetest.10.7.3 CloggingVisually inspect the orifice of each mechanical pump dis

30、penser for the presence of product, either as is, orin a dried state and report the findings in 11.1. If the pump exhibits a high degree of clogging, which interferes with theperformance of the mechanical pump dispenser, try removing the dried product from off the face of the orifice. If this does n

31、otremedy the clog and results in an unusable mechanical pump dispenser, discontinue any additional testing with that particularmechanical pump dispenser and report the findings in 11.1.10.7.4 Output per StrokeDetermine the output per stroke (in accordance with Test Methods D4336) of each mechanical

32、pumpdispenser per D4336.10.7.5 Spray QualityObserve spray quality. Report any leakage and location in 11.1.10.8 Upon completion of the testing outlined in 10.6, return all functioning test specimens to their respective environments forcontinued testing at the next scheduled time interval.10.9 Retain

33、 all test specimens that were discontinued from testing because of one or more defects. Save these if futureexamination is required.11. Report11.1 Report the following information:11.1.1 Description of the mechanical pump dispenser (supplier, type, closure size, diptube length and application torque

34、 ofclosure to bottle),11.1.2 Identification of the product used,11.1.3 Statement to the effect that the tests were made in compliance with this test method practice along with the:11.1.4 Name of the technician completing the test, and11.1.5 Date of report along with dates for the test period.11.1.6

35、Detailed record of test on each mechanical pump dispenser,11.1.7 When a mechanical pump dispenser was discontinued from additional testing and the nature of its discontinuance, and11.1.8 Any observations or recommendations that may assist in correcting the various defects report upon.11.1.9 Data for

36、 each package on strokes to prime and delivery rate. Identify any patterns or trends seen in the delivery ate ofthe packages during the test.11.2 Report the overall results of the testing and draw a conclusion as to the acceptability of the mechanical pump dispenser.If the mechanical pump dispenser

37、is acceptable, but with certain limitations, note accordingly.12. Precision and Bias12.1 PrecisionThe precision is highly dependent on the particular pump style and contents tested. One laboratory hasinvestigated one particular fine mist pump style and a hair spray product with six replicate tests p

38、er temperature variable, yieldingno visual product leakage, very minor cloggage, and all specimens retaining prime. For all specimens evaluated for strokes toprime, the test yielded an average of 6.58 strokes with a range of 6 to 7 strokes and a standard deviation of 0.53 strokes. For the23C specime

39、ns evaluated for output per stroke, the test yielded an average of 0.136 g with a range of 0.130 to 0.142 g and astandard deviation of 0.02 g. For the 45C specimens evaluated for output per stroke, the test yielded an average of 0.136 g witha range of 0.131 to 0.142 g and a standard deviation of 0.0

40、2 g. Other pumps and contents will have other averages and will havemore or less variability between replicate tests. Users of this test method practice are suggested to reference historical files ofprevious tests of similar pumps and contents for an estimate of within laboratory repeatability. The

41、Committee believes thatbecause of this strong product and pump style dependency, further investigation of repeatability and reproducibility is notpracticable.12.2 BiasThis test method practice has no bias because an accepted reference or referee value is not available.D6633 18313. Keywords13.1 funct

42、ional stability; mechanical pump dispenser; packageASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent righ

43、ts, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for r

44、evision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing y

45、ou shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may b

46、e obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 184