1、Designation: D6716 08 (Reapproved 2013)Standard Test Method forTotal Ash in Wet Blue or Wet White1This standard is issued under the fixed designation D6716; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision.
2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of total ash inwet blue and wet white.1.2 For total ash in wet white, the procedure is ide
3、ntical;substitute wet white for wet blue in the standard.1.3 Total ash in wet blue may be reported upon a number ofdifferent bases (for example, fat-free, moisture-free, asreceived, excluding chromium, and so forth). Before proceed-ing with any tests, it is very important to determine upon whichbasi
4、s that the total ash is to be reported and to identify all othertest methods that will be required to be executed in order toachieve the determined reporting method.1.4 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.5 This st
5、andard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1
6、 ASTM Standards:2D3495 Test Method for Hexane Extraction of LeatherD6658 Test Method for Volatile Matter (Moisture) of WetBlue by Oven DryingD6659 Practice for Sampling and Preparation of Wet Bluefor Physical and Chemical TestsD6714 Test Method for Chromic Oxide in Ashed Wet Blue(Perchloric Acid Oxi
7、dation)3. Terminology3.1 Definitions:3.1.1 The terms and definitions employed within this testmethod are commonly used in normal laboratory practice andrequire no special comment.4. Summary of Test Method4.1 The weighed sample is ignited in air at 600 6 25C untilconstant mass is attained. The weighe
8、d residual matter istermed “ash” and is calculated as a percentage of the originalsample.5. Significance and Use5.1 This test method is useful in determining the approxi-mate amount of nonvolatile inorganic material in wet blue.This may be in the form of salts or oxides of the elements. Ina mixed-ch
9、rome tannage, the approximate percentage of otherelements in the wet blue may be determined by subtracting thechromic oxide that may be conveniently determined on the ash.(See Test Method D6714.)5.2 The specified temperature of 600C is high enough toproduce a reproducible result but it does not comp
10、letelydehydrate such oxides as aluminum oxide (Al2O3) and chromicoxide (Cr2O3). Likewise, such salts as sulfates and phosphatesmay be incompletely dehydrated, and if alkalis and chromiumare present simultaneously, oxidation to chromate may occur.Therefore, caution is advised in drawing conclusions b
11、ased onquantitative relations of the elements.6. Apparatus6.1 Crucible, 30- to 50-mL, high-form, platinum or porce-lain.6.2 Electric Muffle Furnace, with controller or rheostat andpyrometer, capable of maintaining a temperature of 600 625C.6.3 Dessicator, of appropriate size and charged with freshde
12、ssicant.6.4 Analytical Balance, capable of accurate weighings towithin 0.001 g.7. Test Specimen7.1 The specimen shall consist of 2 to 10 g of wet blue fromthe composite sample, prepared in accordance with PracticeD6659.1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand i
13、s the direct responsibility of Subcommittee D31.02 on Wet Blue.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 2001. Last previous edition approved in 2008 as D6716 08. DOI:10.1520/D6716-08R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcon
14、tact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1NOTE 1Typically, wet b
15、lue is a combination of organic hide substancein conjunction with inorganic chromium tanning salts. However, undersome circumstances, silicones or other solvent-soluble organo-metalliccomplexes (including electrolyte-stable fat liquors) are added duringmanufacture and may be present within the sampl
16、e. It may be desirable tocalculate ash upon an extracted (fat free) basis, and if so, this should beindicated within the final report. To report ash upon an extracted basis, itwill be necessary to execute Test Method D3495 on a portion of the samesample and weighed out at the same time as the specim
17、en for total ashdetermination.8. Procedure8.1 Weigh accurately into a tared crucible 2 to 10 g (60.001g) of wet blue, prepared as described in 7.1, and preferably atsufficiently close equilibrium with the laboratory humidity thatit does not gain or lose mass (moisture) at a significant rate.8.2 Plac
18、e the crucible and sample in the muffle furnace andmaintain at 600 6 25C for at least 4 h, or longer if necessary,to destroy carbonaceous matter (Note 2).8.3 To prevent any loss of ash, very carefully remove thecrucible from the furnace, cool in a desiccator, and weigh(Note 3). Ensure that the trans
19、fer of the crucible from oven todessicator is smooth and that there are no external air draughtsthat could cause loss of ash.8.4 Replace in the furnace and maintain at 600 6 25C foranother 15 min.8.5 Repeat the weighing operation.8.6 Continue heating for 15 min and weighing as describedabove until a
20、 mass constant within 0.002 g (2 mg) is obtained.8.7 Record the final weight.NOTE 2The procedure in Section 8 is satisfactory with most wet blue.However, with wet blue that is known or suspected to have a very highgrease content or has been heavily treated with fats and oils duringprocessing, start
21、with a cold muffle and raise temperature gradually to600C, or burn off the oil carefully over a gas burner before placing thecrucible in the hot furnace.NOTE 3If it is difficult to burn off the carbon, as evidenced byinspection or failure to achieve constant mass, moisten the ash with a fewdrops of
22、1:1 nitric acid, dry carefully over a low flame, and then transferto the muffle furnace and heat as before. If this procedure is unsuccessful,digest the ash in the crucible with 15 to 20 mL of hot water for a fewminutes, and filter the suspension through an ashless high-retention filterpaper. Transf
23、er the paper and insoluble residue to the crucible and igniteat 600 6 25C as described above. Cool, add the filtrate to the crucible,evaporate carefully to dryness, then ignite at 600 6 25C to constant massas described previously.9. Calculation9.1 Calculate the percentage of ash in the wet blue weig
24、hedas follows:Ash, % 5 A 2 B!C 2 B!# 3100where:A = weight of the ash and crucible,B = weight of the crucible, andC = weight of the sample and crucible.9.2 If it is desired to convert the percentage obtained aboveto the dry basis, perform a moisture determination (TestMethod D6658) on a portion of th
25、e same sample weighedunder the same conditions as in Section 8. If the percentagemoisture found is D, then calculate the percentage of ash on adry basis as follows:Ash, dry basis, % 5 A 2 B!C 2 B!# 3 100/1 2 D/100!#where A, B, and C have the same meaning as in 9.1.10. Precision and Bias10.1 Precisio
26、nThe precision of this test method is largelylimited by the homogeneity of the sample in a complex naturalmaterial such as wet blue.10.2 RepeatabilityAt the 95 % confidence level, duplicatedeterminations by the same operator should not differ by morethan 0.14 % ash.10.3 ReproducibilityAt the 95 % co
27、nfidence level, theaverage of duplicate determinations in each of two laboratoriesby different operators should not differ by more than 0.20 %ash.10.4 BiasInasmuch as all wet blue contains an unknownamount of natural or inherent ash, no meaningful statement canbe made with respect to bias.11. Keywor
28、ds11.1 aluminum oxide; ash; blue stock; chrome content;chromic oxide; total ash; wet blue; wet whiteASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that dete
29、rmination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or
30、 withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel tha
31、t your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints
32、(single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D6716 08 (2013)2
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1