ASTM D6887-2003(2013) 5000 Standard Test Method for Testing Alkyd Compatibility with Resin or Resin Solutions《测试醇酸树脂与树脂或树脂溶液的相容性的标准试验方法》.pdf

1、Designation: D6887 03 (Reapproved 2013)Standard Test Method forTesting Alkyd Compatibility with Resin or Resin Solutions1This standard is issued under the fixed designation D6887; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the procedure for determiningthe degree of compatibility of an alkyd with a specific

3、resin orresin solution.1.2 The most common use of this method is to test alkydcompatibility with a hydrocarbon resin or a solution of theresin in an aliphatic solvent, for lithographic ink vehicleapplications.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurem

4、ent are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitat

5、ions prior to use.2. Referenced Documents2.1 ASTM Standards:2D6038 Test Methods for Determining the Compatibility ofResin/Solvent Mixtures by Precipitation Temperature(Cloud Point)3. Terminology3.1 Definitions:3.1.1 compatibility, nresin and solvent mixture forms aclear, homogenous, and stable solut

6、ion. D60383.1.2 incompatibility, nresin and solvent mixture does notform a clear, homogenous, and stable solution.4. Summary of Test Method4.1 The required resin to alkyd ratio is mixed into a 150-mLbeaker and heated to 160C until clear and homogenous.4.2 The solution is placed into pre-labeled jars

7、 and cooled.4.3 Degree of compatibility is reported at 30 min and 24 hafter cooling to room temperature.5. Significance and Use5.1 Incompatibility of the system can lead to loss of gloss,decreased color strength, rheological problems and grind issuesin the flush or pigment base.5.2 This method is us

8、ed in the lithographic industry, espe-cially in pigment wetting applications, where the alkyd may ormay not be totally compatible with the resin selected for theapplication.6. Apparatus6.1 Beakers, 150 mL (4).6.2 Jars, with lids, 4 oz (4).6.3 Balance, capacity of at least 200 g, accurate to 60.1 g.6

9、.4 Hot Plate, capable of heating to a minimum of 200C.6.5 Thermometer, 0 to 200C, 61C.6.6 Spatula, or stirrer rods.7. Test Samples7.1 Alkyd to be tested.7.2 Resin or resin solution.8. Procedure8.1 Label each jar and beaker with the resin, alkyd and ratiobeing tested.8.2 Weigh into the beaker the fol

10、lowing materials:MaterialRatio2:1 3:1 4:1 5:1Resin/Resin Solution 16.0g 18.0g 20.0g 20.0gAlkyd 8.0g 6.0g 5.0g 4.0g8.3 Place the beakers on the hot plate and heat to 160C. Stirwith spatula or stir rod until clear.8.4 Pour the blend from each beaker into the appropriatelylabeled jar then cool to room

11、temperature.8.5 Wait 30 min then visually observe degree of clarity ofeach test sample.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.37 on Ink Vehicles.Current edition ap

12、proved June 1, 2013. Published June 2013. Originallyapproved in 2003. Last previous edition approved in 2008 as D6887 03 (2008).DOI: 1520/D6887-03R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStand

13、ards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1NOTE 1Some applications may require a longer waiting time such as24 h. If this is the case, recor

14、d compatibility of the solution after 24 h.9. Report9.1 Report the highest ratio where the blend remained clearafter 30 min or 24 h (time should be agreed upon by user of thistest method and application).9.2 If the mixtures are clear at all ratios tested, then the resincan be considered compatible t

15、o the highest ratio tested.10. Precision and Bias310.1 An inter-laboratory study was conducted in which sixlaboratories tested the compatibility of two hydrocarbon resinswith two alkyds. All laboratories agreed on the compatibility/incompatibility of each hydrocarbon resin with each alkyd.However, s

16、ince the test is non-quantitative, it is not possible tocompute repeatability, reproducibility or bias.11. Keywords11.1 aliphatic solvents; alkyds; compatibility; hydrocarbonresins; lithographic inks; pigment wettings; resin solutionsASTM International takes no position respecting the validity of an

17、y patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to rev

18、ision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your

19、 comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyr

20、ighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org

21、 (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).3Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D01-1128.D6887 03 (2013)2