1、Designation: D6984 10aStandard Test Method forEvaluation of Automotive Engine Oils in the Sequence IIIF,Spark-Ignition Engine1This standard is issued under the fixed designation D6984; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision
2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis test method described can be used by any properly equipped laboratory; it does not require theassis
3、tance of anyone outside that laboratory. However, the ASTM Test Monitoring Center (TMC)2provides reference oils and an assessment of the test results obtained on those oils by the laboratory(see Annex A1). By these means, the laboratory will know whether their use of the test method givesresults sta
4、tistically similar to those obtained by other laboratories. Furthermore, various agenciesrequire that a laboratory utilize the TMC services in seeking qualification of oils against specifications.For example, the U.S. Army imposes such a requirement in connection with several Army enginelubricating
5、oil specifications.Accordingly, this test method is written for use by laboratories that utilize the TMC services.Laboratories that choose not to use those services may simply ignore those portions of the test methodthat refer to the TMC.This test method may be modified by means of Information Lette
6、rs issued by the TMC. In addition,the TMC may issue supplementary memoranda related to the test method (see A1.8).1. Scope1.1 This test method covers an engine test procedure forevaluating automotive engine oils for certain high-temperatureperformance characteristics, including oil thickening, varni
7、shdeposition, oil consumption, as well as engine wear. Such oilsinclude both single viscosity grade and multiviscosity gradeoils that are used in both spark-ignition, gasoline-fueledengines, as well as in diesel engines.NOTE 1Companion test methods used to evaluate engine oil perfor-mance for specif
8、ication requirements are discussed in SAE J304.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.2.1 ExceptionsThe values stated in inches for ring gapmeasurements are to be regarded as standard, and where thereis no direct
9、SI equivalent such as screw threads, National PipeThreads/diameters, tubing size, or single source supply equip-ment specifications.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establ
10、ish appro-priate safety and health practices and determine the applica-bility of regulatory requirements prior to use.1.4 This test method is arranged as follows:Subject SectionScope 1Referenced Documents 2Terminology 3Summary of Test Method 4Significance and Use 5Apparatus 6Laboratory 6.1Drawings 6
11、.2Specified Equipment 6.3Test Engine 6.4Engine Parts 6.4.1Engine Speed and Load Control 6.5Sequence IIIF Fluid Conditioning Module 6.6Engine Cooling System 6.6.1Flushing Tank 6.7Coolant Mixing Tank 6.8Condenser Cooling Systems 6.91This test method is under the jurisdiction of ASTM Committee D02 onPe
12、troleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.B0.01 on Passenger Car Engine Oils.Current edition approved July 1, 2010. Published August 2010. Originallyapproved in 2003. Last previous edition approved in 2010 as D698410. DOI:10.1520/D6984-10a.2Until the next re
13、vision of this test method, the ASTM Test Monitoring Centerwill update changes in the test method by means of information letters. Informationletters may be obtained from theASTM Test Monitoring Center, 6555 PennAvenue,Pittsburgh, PA 15206-4489. Attention: Administrator. www.astmtmc.cmu.edu. Thisedi
14、tion incorporates revisions contained in all information letters through 09-1.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.Subject SectionEngine Oil-Cooling System 6.10Fuel System 6.11Induction Air Supply Humidity, Temperature, an
15、d Pressure 6.12Temperature Measurement 6.13Thermocouple Location 6.13.1Air-to-Fuel Ratio Determination 6.14Injector Flow Testing 6.14.1Exhaust and Exhaust Back Pressure Systems 6.15Blowby Flow Rate Measurement 6.16Pressure Measurement and Sensor Location 6.17Reagents and Materials 7Test Fuel 7.1Engi
16、ne and Condenser Coolant 7.2Coolant Additive 7.3Coolant Preparation 7.4Pre-Test Cleaning Materials 7.5Sealing and Anti-seize Compounds 7.6Test Oil Sample Requirements 8Preparation of Apparatus 9Condenser Cleaning 9.1Intake Manifold Cleaning 9.3Cleaning of Engine Parts (other than the block and heads
17、) 9.4Engine Block Cleaning 9.5Cylinder Head Cleaning 9.6Engine Build-up Procedure 9.7General Information 9.7.1Special Parts 9.7.2Hardware Information 9.7.3Fastener Torque Specifications and Torquing Proce-dures9.7.4Parts Replacement 9.8Engine Block Preparation 9.9Piston Fitting and Numbering 9.10Pis
18、ton Ring Fitting 9.10.1Pre-Test Camshaft and Lifter Measurements 9.11Camshaft Bearing Installation 9.12Camshaft Installation 9.13Main Bearings 9.14Crankshaft Installation 9.14.1Main Bearing Cap Installation 9.14.2Crankshaft Sprocket 9.15Camshaft Sprocket and Timing Chain 9.16Crankshaft End Play 9.17
19、Piston Pin Installation 9.18Piston Installation 9.18.1Harmonic Balancer 9.19Connecting Rod Bearings 9.20Engine Front Cover 9.21Coolant Inlet Adapter 9.22Oil Dipstick Hole 9.23Oil Pan 9.24Cylinder Head Assembly 9.25Adjustment of Valve Spring Loads 9.26Cylinder Head Installation 9.27Hydraulic Valve Li
20、fters 9.28Pushrods 9.29Valve Train Loading 9.30Intake Manifold 9.31Rocker Covers 9.32Water Inlet Adapter 9.33Condenser 9.34Coolant Outlet Adapter 9.35External Oil Cooling System 9.36Oil Sample Valve 9.37Ignition System 9.38Throttle Body 9.39Accessory Drive Units 9.40Exhaust Manifolds, Water-Cooled 9
21、.41Engine Flywheel 9.42Pressure Checking of Engine Coolant System 9.43Lifting of Assembled Engines 9.44Mounting the Engine on the Test Stand 9.45External Cooling System Cleaning 9.46Engine Coolant Jacket Cleaning (Flushing) 9.47Coolant Charging 9.48Test Oil Charging 9.49Subject SectionEngine Oil Pum
22、p Priming 9.50Calibration 10Laboratory and Engine Test Stand Calibration 10.1Testing of Reference Oils 10.2Reference Oil Test Frequency 10.3Reporting of Reference Oil Test Results 10.4Evaluation of Reference Oil Test Results 10.5Status of Non-Reference Oil Tests Relative to ReferenceOil Test10.6Stat
23、us of Test Stands Used for Non-Standard Tests 10.7Data Acquisition and Control 10.8Sample Rate 10.8.1Measurement Accuracy 10.8.2Temperature 10.8.3Pressure 10.8.4Flow 10.8.5Speed 10.8.6Load 10.8.7Measurement Resolution 10.8.8System Time Response 10.8.9Quality Index 10.8.10Engine Operating Procedure 1
24、1Dipstick and Hole Plug 11.1Dipstick Hole O-ring 11.2Engine Start-up and Shutdown Procedures 11.3Start-up 11.4Scheduled Shutdown 11.5Non-Scheduled Shutdowns 11.6Oil Sampling 11.7Oil Leveling 11.8Air-to-Fuel-Ratio Measurement and Control 11.9Air-to-Fuel Ratio Verification 11.10Blowby Flow Rate Measur
25、ement 11.11NOxDeterminations 11.12Data Recording 11.13Initial Run (10 min) 11.14Engine Oil Quality Testing (80 h) 11.15Test Termination 11.16Determination of Test Results 12Engine Disassembly 12.2Preparation of Parts for Rating of Sticking, Deposits,and Plugging12.3Piston Deposit Rating 12.4Post-Tes
26、t Camshaft and Lifter Wear Measurements 12.5End-of Test Used Oil Sample Testing 12.6Viscosity Test 12.7Testing Oil Samples for Wear Metals 12.8Blowby Flow Rate Measurements 12.9Oil Consumption Computation 12.10Photographs of Test Parts 12.11Retention of Representative Test Parts 12.12Severity Adjust
27、ments 12.13Determination of Operational Validity 12.14Report 13Report Forms 13.1Precision of Reported Units 13.2Deviations from Test Operational Limits 13.3Precision and Bias 14Keywords 15AnnexesThe Role of the ASTM Test Monitoring Center (TMC) andthe Calibration ProgramAnnex A1Sequence IIIF Test Pa
28、rts Replacement Guidelines Annex A2Sequence IIIF Determination Volume of Engine Oil in Pan Annex A3Sequence IIIF Test Fuel Analysis Annex A4Sequence IIIF Test Reporting Annex A5Sequence IIIF Test Air-to-Fuel Ratio Control Flow Chart Annex A6Sequence IIIF Test Set Points and Control States Annex A7Se
29、quence IIIF Quality Index Upper and Lower Values Annex A8Sequence IIIF Engine Oil Level Worksheet Annex A9Blowby Flow Rate Determination Annex A12Safety Precautions Annex A12Sequence IIIF Blueprint Listing Annex A13Fluid Conditioning Module Components Annex A14AppendixSequence IIIFHD Test Procedure
30、Appendix X1D6984 10a2Subject SectionSequence IIIFVIS Test Procedure Appendix X22. Referenced Documents2.1 ASTM Standards:3D16 Terminology for Paint, Related Coatings, Materials,and ApplicationsD86 Test Method for Distillation of Petroleum Products atAtmospheric PressureD130 Test Method for Corrosive
31、ness to Copper from Pe-troleum Products by Copper Strip TestD235 Specification for Mineral Spirits (Petroleum Spirits)(Hydrocarbon Dry Cleaning Solvent)D240 Test Method for Heat of Combustion of LiquidHydrocarbon Fuels by Bomb CalorimeterD323 Test Method for Vapor Pressure of Petroleum Prod-ucts (Re
32、id Method)D381 Test Method for Gum Content in Fuels by Jet Evapo-rationD445 Test Method for Kinematic Viscosity of Transparentand Opaque Liquids (and Calculation of Dynamic Viscos-ity)D525 Test Method for Oxidation Stability of Gasoline(Induction Period Method)D1319 Test Method for Hydrocarbon Types
33、 in LiquidPetroleum Products by Fluorescent Indicator AdsorptionD2699 Test Method for Research Octane Number of Spark-Ignition Engine FuelD2700 Test Method for Motor Octane Number of Spark-Ignition Engine FuelD3231 Test Method for Phosphorus in GasolineD3237 Test Method for Lead in Gasoline by Atomi
34、c Ab-sorption SpectroscopyD3338 Test Method for Estimation of Net Heat of Combus-tion of Aviation FuelsD3343 Test Method for Estimation of Hydrogen Content ofAviation FuelsD4052 Test Method for Density, Relative Density, and APIGravity of Liquids by Digital Density MeterD4175 Terminology Relating to
35、 Petroleum, PetroleumProducts, and LubricantsD4294 Test Method for Sulfur in Petroleum and PetroleumProducts by Energy Dispersive X-ray Fluorescence Spec-trometryD4485 Specification for Performance of Engine OilsD4684 Test Method for Determination of Yield Stress andApparent Viscosity of Engine Oils
36、 at Low TemperatureD4815 Test Method for Determination of MTBE, ETBE,TAME, DIPE, tertiary-Amyl Alcohol and C1to C4Alco-hols in Gasoline by Gas ChromatographyD5185 Test Method for Determination of Additive Ele-ments, Wear Metals, and Contaminants in Used Lubricat-ing Oils and Determination of Selecte
37、d Elements in BaseOils by Inductively Coupled Plasma Atomic EmissionSpectrometry (ICP-AES)D5191 Test Method for Vapor Pressure of Petroleum Prod-ucts (Mini Method)D5293 Test Method for Apparent Viscosity of Engine Oilsand Base Stocks Between 5 and 35C Using Cold-Cranking SimulatorD5452 Test Method f
38、or Particulate Contamination in Avia-tion Fuels by Laboratory FiltrationD5453 Test Method for Determination of Total Sulfur inLight Hydrocarbons, Spark Ignition Engine Fuel, DieselEngine Fuel, and Engine Oil by Ultraviolet FluorescenceD5862 Test Method for Evaluation of Engine Oils inTwo-Stroke Cycl
39、e Turbo-Supercharged 6V92TA DieselEngine4D6557 Test Method for Evaluation of Rust PreventiveCharacteristics of Automotive Engine OilsD6593 Test Method for Evaluation of Automotive EngineOils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasolineand Op
40、erated Under Low-Temperature, Light-Duty Con-ditionsD6750 Test Methods for Evaluation of Engine Oils in aHigh-Speed, Single-Cylinder Diesel Engine1K Proce-dure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % FuelSulfur)D7320 Test Method for Evaluation of Automotive EngineOils in the Sequence IIIG, Spar
41、k-Ignition EngineD7422 Test Method for Evaluation of Diesel Engine Oils inT-12 Exhaust Gas Recirculation Diesel EngineE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE191 Specification for Apparatus For Microdeterminationof Carbon and Hydrogen in Org
42、anic and Organo-MetallicCompoundsE608/E608M Specification for Mineral-Insulated, Metal-Sheathed Base Metal ThermocouplesE1119 Specification for Industrial Grade Ethylene GlycolG40 Terminology Relating to Wear and ErosionIEEE/ASTM SI-10 Standard for Use of the InternationalSystem of Units (SI): The M
43、odern Metric System2.2 Military Specification:5MIL-PRF-2104 Lubricating Oil, Internal Combustion En-gine, Tactical Service2.3 SAE Standards:6J183 Engine Oil Performance and Engine Service Classifi-cation (Other Than “Energy-Conserving”)J300 Engine Oil Viscosity Classification *HS-23/00*J304 Engine O
44、il Tests3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Withdrawn. The last approved version of this histori
45、cal standard is referencedon www.astm.org.5Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098.6Available from Society of Automotive Engineers, 400 Commonwealth Dr.,Warrendale, PA 15096-0001. These standards are not available
46、separately. Ordereither SAE Handbook Vol. 3, or SAE Fuels and Lubricants Standards ManualHS-23.D6984 10a32.4 Other Document:7CRC Manual 20 Rating Techniques and Breakdown Meth-ods3. Terminology3.1 Definitions:3.1.1 blowby, nin internal combustion engines, that por-tion of the combustion products and
47、 unburned air/fuel mixturethat leaks past piston rings into the engine crankcase duringoperation.3.1.2 BTDC (before top dead center), nused with thedegree symbol to indicate the angular position of the crankshaftrelative to its position at the point of uppermost travel of thepiston in the cylinder.3
48、.1.3 calibrate, vto determine the indication or output ofa device (e.g., thermometer, manometer, engine) with respectto that of a standard.3.1.4 clogging, nthe restriction of a flow path due to theaccumulation of material along the flow path boundaries.D41753.1.5 cold-stuck piston ring, nin internal
49、 combustionengines, a piston ring that is stuck when the piston and ring areat room temperature, but inspection shows that it was freeduring engine operation.3.1.5.1 DiscussionA cold-stuck piston ring cannot bemoved with moderate finger pressure. It is characterized by apolished face over its entire circumference, indicating essen-tially no blowby passed over the ring face during engineoperation. D41753.1.6 correction factor, na mathematical adjustment to atest result to compensate for industry-wide shifts in severity.D41753.1.7 corrosion, nthe chemical or electrochem
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1