1、Designation: D 7025 09Standard Test Method forAssessing Clean Flax Fiber Fineness1This standard is issued under the fixed designation D 7025; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in pa
2、rentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method provides two options that cover thedetermination of the fineness of clean loose flax fibers by:Option 1, measuring the specific su
3、rface area by the resistanceof a plug of flax fibers to air flow under prescribed conditions,or Option 2, estimating the mass per unit length.NOTE 1For other methods for determining the fineness of fibers referto Appendix X1.1.2 The values stated in SI units are to be regarded asstandard. No other u
4、nits of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of re
5、gulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 123 Terminology Relating to TextilesD 1441 Practice for Sampling Cotton Fibers for TestingD 1577 Test Methods for Linear Density of Textile FibersD 1776 Practice for Conditioning and Testing TextilesD 6798 Terminology Rel
6、ating to Flax and Linen3. Terminology3.1 Definitions:3.1.1 fineness index, nthe use of a cellulosic fiber tomeasure air permeability having a specific gravity of 1.5 and anominal linear density of 1.1 denier, 1.5 denier, or 3.0 denier.3.1.1.1 DiscussionViscose rayon fiber samples are lessvariable th
7、an natural fibers and manufactured to exactingproperties by many fiber distributors. These fibers are derivedfrom regenerated cellulose to contain a chemically inducedcrimp (4 to 6 crimps/cm) and a staple length of approximately5 cm. Linear density of these fibers can be verified using thebundle wei
8、ghing Option A of Test Method D 1577 to beapproximately 0.11, 0.17, and 0.33 mg/m. As detailed in TestMethod D 1577, fibers were cut with a mechanical cuttingdevice under sufficient tension to remove fiber crimp. Thesecellulosic fibers have the same specific gravity as flax and canbe used to determi
9、ne the specific surface area.3.1.2 specific surface index, nrelative fineness obtainedby measuring the specific surface area by the resistance ofairflow through a known mass of fiber compressed to a fixedvolume.3.1.2.1 DiscussionThe specific surface index is influ-enced by various types of flax whos
10、e fiber perimeter, fiberbundles, cross-sectional shape, density, and trash differ be-tween samples.3.2 For definitions of textile terms used in this test method,refer to Terminology D 6798.3.3 For definitions of other terms used in this test method,refer to Terminology D 123.4. Summary of Test Metho
11、d4.1 Using Option 1, a predetermined mass of clean looseflax fibers generated by using a mechanical blender is placed inthe specimen holder and compressed to a fixed volume.4.1.1 The resistance to airflow is measured using a cottonfiber instrument that provides a reading. This reading isconverted to
12、 a specific surface index which is derived from thelinear density of flax.4.2 Using Option 2, the average linear density of singlefibers in a bundle is calculated from mass and length measure-ments on the bundle and the number of single fibers in thebundle.NOTE 2There may be no overall correlation b
13、etween the resultsobtained with Options 1 and 2. Consequently, these two options cannot beused interchangeably. In case of controversy, Option 1 shall prevail.5. Significance and Use5.1 This test method for determining fineness of cleanedflax fibers is considered satisfactory for acceptance testing
14、ofcommercial shipments when the levels are controlled by use ofa range of calibration standards.5.1.1 If there are differences of practical significance be-tween reported test results for two or more laboratories,comparative tests should be performed by those laboratories to1This test method is unde
15、r the jurisdiction ofASTM Committee D13 on Textilesand is the direct responsibility of Subcommittee D13.17 on Flax and Linen.Current edition approved July 1, 2009. Published August 2009. Originallyapproved in 2004. Last previous edition approved in 2004 as D 702504a1.2For referenced ASTM standards,
16、visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1942
17、8-2959, United States.determine if there is a statistical bias between them, usingcompetent statistical assistance. As a minimum, use testsamples that are as homogenous as possible, are drawn fromthe material from which the disparate test results were ob-tained, and are randomly assigned in equal nu
18、mbers to eachlaboratory for testing. These test results from the two labora-tories should be compared using a statistical test for unpaireddata, at a probability level chosen prior to the testing series. Ifa bias is found, either its cause must be found and corrected, orfuture test results for that
19、material must be adjusted inconsideration of the known bias.5.2 The resistance that a plug of flax fibers offers to the flowof air is measured as an approximate indication of the averagerelative fineness of the fibers.5.2.1 The total surface area of finer fibers has a larger perunit mass and increas
20、ed resistance to airflow than do coarserfibers.5.3 Instruments are available to indicate the resistance to airflow using either compressed air or a vacuum; and areconstructed (1) to measure airflow under constant pressuredrop across the plug, (2) to measure pressure drop when aconstant flow of air i
21、s maintained, or (3) to indicate resistanceto air flow from both a balanced and unbalanced Wheatstonebridge.5.4 The reliability of the results of any test method dependsprimarily upon how well the specimens tested represent theoriginal source material. Flax fibers are different from manytextile fibe
22、rs, such as cotton or synthetic ones, in that they arenot individual filaments but bundles of fibrous material thatmay or may not be completely separated into individualfilaments and therefore have a high degree of variability. Whilecleaning and processing can produce separation and changes inlength
23、, there is no certainty of fibrillation of the fibrousmaterial.NOTE 3A modification of this test method can be used in commercialtrading to select bales that will conform to contract guarantees forspecified specific surface index. For this purpose, the usual practice to testonly one specimen per sam
24、ple.5.4.1 This specific surface index reading is related to theaverage linear density of single fibers in a bundle calculatedfrom mass and length measurements on the bundle and thenumber of single fibers in the bundle.5.5 The specific surface index of flax fibers may be afunction of fineness, degree
25、 of retting, cleanliness, variety,bundle separation, and plant maturity harvest date. This fine-ness of flax fibers affects their mill processing and spinningperformance as well as contributes significantly to the appear-ance and strength of the yarns produced.5.6 The accuracy of weighing can be con
26、trolled by thenumber of fibers composing the bundle. However, with shortfiber of low linear density the number of fibers to be countedbecomes prohibitive unless the bundle mass is kept low.6. Apparatus and Materials6.1 Air-Flow Instrument,3a device calibrated in micronairereadings or yielding numeri
27、cal readings from which specificsurface index readings can be computed.6.2 Balances, with one having a capacity suitable for massof the specific surface index specimen to be used and sensitiv-ity of at least 0.2 % of the mass and another for linear densityhaving a capacity of 15 mg and sensitivity o
28、f at least 0.005 mg.6.3 Air Supply, to furnish the required pressure or vacuum tooperate the instrument in accordance with the manufacturersinstructions.6.4 Fineness Calibration Standards, viscose rayon fibersreduced to 5 cm with a nominal linear density of 1.1, 1.5, or 3.0denier and a nominal speci
29、fic surface fineness index value of2.55, 2.9, or 4.0.6.5 Mechanical Cutting Device, Template, StelometerClamps, or Die, having a precision of 0.1 % designed to permitcutting fibers of a specified length.6.6 Stationary Coarse Comb, approximately 63 mm inwidth and having needles approximately 12.5 mm
30、in lengthand spaced 19 needles to the centimeter.6.7 Mechanical Blender, to open and blend the flax fibers.7. Sampling and Selection of Specimens7.1 Take the test specimen by random sampling from thelaboratory sample prepared as recommended in PracticeD 1441.7.1.1 Pass the test specimen through a me
31、chanical blenderto open and blend fibers as directed in 6.1 of recommendedPractice D 1441.8. Conditioning8.1 Bring the laboratory sample from the prevailing atmo-sphere to moisture equilibrium for testing which is 21 6 1C(70 6 2F) and 65 6 2 % relative humidity and check theequilibrium as directed i
32、n Practice D 1776. No preconditioningis required.OPTION 1: SPECIFIC SURFACE INDEX FINENESS9. Scope9.1 This option covers the fineness measurement by resis-tance to airflow which is converted to the specific surface indexto help characterize fibers by approximating the fineness. (SeeNote 2.)10. Proce
33、dure10.1 Test the conditioned calibration specimens in theatmosphere for testing textiles.10.1.1 Set up and adjust the instrument as directed in themanufacturers instructions.3Apparatus and accessories are commercially available.D702509210.1.2 Adjust the instrument if necessary to secure values,whic
34、h correspond to the values assigned to the CalibrationReference Standards at the beginning of each testing period.10.2 Use a mechanical blender twice to open and blend eachstandard viscose rayon fiber.10.3 Using 5 g specimens, make two tests with eachstandard viscose rayon fiber.10.3.1 When the aver
35、age of the two results is not within 0.1unit of the established specific surface index reading, recheckthe instrument and the technique used by the operator.10.3.2 Check the instrument against the standards again atthe end of each testing period.10.3.3 When incorrect readings on the standards are ob
36、-tained at the end of a testing period, discard the results, recheckthe instrument, and repeat the tests.410.4 Test the conditioned laboratory specimens in the atmo-sphere for testing textiles.10.5 Use a mechanical blender twice to open and blend flaxfibers. Using forceps, remove obvious, large piec
37、es of shiveand other foreign materials.10.5.1 Weigh outa5gtest specimen for the instrument.10.5.2 Place the weighed specimen in the fiber compressioncylinder, fluffing it with the fingers as it is packed into thecylinder to eliminate knotty balls and being careful to place allthe fibers inside the c
38、ylinder. Insert or activate the fibercompression plunger. Turn on or activate the air and read thevalue to the nearest 0.1 unit reading.10.6 Test three specimens for each laboratory sampling unit.11. Calculations11.1 If the instrument readings are not in resistance toairflow readings, compute resist
39、ance to airflow readings frominstrument readings in accordance with manufacturers instruc-tions.11.2 Convert resistance to airflow readings into specificsurface index fineness values, using Eq 1:SSI 5 J13 R! 2 J2(1)where:SSI = specific surface index,R = resistance to airflow reading,J1= 0.899, andJ2
40、= 2.023.Factors determined by linear regression between resistanceto airflow readings and linear density values using 9 Interna-tional Flax Grades.11.3 Calculate the average for the three specimens test to thenearest 0.1 specific surface index reading for each laboratorysampling unit and for the lot
41、.OPTION 2: LINEAR DENSITY FINENESS12. Scope12.1 This option measures the fineness by determining thelinear density of flax fiber which is cut and weighed. Averagelinear density of single fibers in a bundle is calculated frommass and length measurements on the bundle and the numberof single fibers in
42、 the bundle. (See Note 2.)13. Test Specimens13.1 From each laboratory-sampling unit in a container,take three specimens at random.13.2 Select tufts or bundles of fibers containing a sufficientnumber of fibers to weigh between 0.5 and 7.5 mg when cut toa specified length.14. Preparation of Specimens1
43、4.1 The specimens chosen from staple fiber may requirecombing to align the fibers and remove short ends and obviouslarge pieces of nonfibrous materials.14.1.1 Grip the specimen at one end in suitable clamp ortweezers. Ease the specimen onto the stationary coarse combneedles 3 to 5 mm on the clamp si
44、de of the center of the tuft.Draw the specimen gently toward the center.14.1.2 Lift the specimen off the comb. Replace the speci-men on the needles 3 to 5 mm closer to the clamp than the lastposition. Draw the specimen gently to the center as before.14.1.3 Continue to comb the specimen until the cla
45、mp isreached and all unclamped fibers are drawn to the center.14.1.4 Reverse the specimen. Clamp in the combed segmentapproximately 3 to 5 mm from the uncombed segment near thecenter. Comb the other end of the specimen, progressing fromtip to center in 3 to 5 mm increments. Discard the combings.14.1
46、.5 Arrange fibers in parallel alignment.15. Procedure15.1 Test the specimens in the standard atmosphere fortesting textiles.15.2 Place the combed bundle of fibers in a cutting devicewith fibers in parallel alignment and cut to known length.15.3 Count 500 fibers in the combed bundle of fibers.5NOTE 4
47、Counting of fibers is facilitated by using some magnificationand shuffling the specimen on a short pile surface of contrasting color toseparate fibers. Small fiber bundles still attached are counted as a singlefiber.15.4 Weigh the 500 fibers from the specimen to the nearest0.005 mg.15.5 Test three s
48、pecimens for each laboratory sampling unit.16. Calculations16.1 Calculate the average fiber linear density for eachspecimen to the nearest 0.1 mg/m.16.2 Calculate the average for the three specimens test tothe nearest 0.1 mg/m fiber linear density reading, using Eq 2:LD 5 W/L 3 N! (2)where:LD = aver
49、age fiber linear density (mg/m),W = mass of bundle specimen (mg),4Built-in calibration devices and calibration plugs alone give only approximateresults.5It is complicated to obtain the linear density of a group or individual flax fibersbecause of fiber bundles being partially divided. Consequently, extra flax fibers mustbe counted, which results in fiber bundles that are still joined together being countedas a single fiber.D7025093L = length of bundle specimen (m), andN = number of fibers and attached fibers in the bundlespecimen (500 fibers).16.3 Calculate the mean o
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1